ROHM BA2903YFE2

Comparator series
Automotive
Ground Sense Comparators
BA2903Yxxx-C, BA2901Yxx-C
●Key Specifications
 Wide operating supply voltage
single supply :
split supply :
 Very low supply current
BA2903Yxxx-C
BA2901Yxx-C
 Low input bias current :
 Low input offset current :
 Operating temperature range :
●General Description
BA2903Yxxx-C/BA2901Yxx-C, integrate two or four
independent high gain voltage comparator.
Some features are the wide operating voltage that is 2
V to 36V and low supply current. BA2903Yxxx-C,
BA2901Yxx-C are manufactured for automotive
requirements of engine control unit, electric power
steering, antilock brake system, etc.
●Features
 AEC-Q100 Qualified
 Single or dual supply operation
 Wide operating supply voltage
 Standard comparator Pin-assignments
 Common-mode Input Voltage Range includes ground
level, allowing direct ground sensing
 Internal ESD protection circuit
 Wide temperature range
●Packages
SOP8
SOP14
SSOP-B8
SSOP-B14
MSOP8
+2.0V to +36V
±1.0V to ±18V
0.6mA(Typ.)
0.8mA(Typ.)
50nA(Typ.)
5nA(Typ.)
-40℃ to +125℃
W(Typ.) x D(Typ.) x H(Max.)
5.00mm x 6.20mm x 1.71mm
8.70mm x 6.20mm x 1.71mm
3.00mm x 6.40mm x 1.35mm
5.00mm x 6.40mm x 1.35mm
2.90mm x 4.00mm x 0.90mm
●Application
 Engine Control Unit
 Electric Power Steering (EPS)
 Anti-Lock Braking System (ABS)
 Automotive electronics
●Selection Guide
Maximum Operating Temperature
+125℃
Supply Current
Automotive
Dual
0.6mA
Quad
0.8mA
BA2903YF-C
BA2903YFV-C
BA2903YFVM-C
BA2901YF-C
BA2901YFV-C
●Simplified schematic
VCC
OUT
+IN
-IN
VEE
Figure 1. Simplified schematic (one channel only)
○Product structure：Silicon monolithic integrated circuit
○This product is not designed protection against radioactive rays.
www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111･14･001
1/29
TSZ02201-0RFR1G200120-1-2
11.Mar.2013 Rev.003
Datasheet
BA2903Yxxx-C, BA2901Yxx-C
●Pin Configuration
BA2903YF-C : SOP8
BA2903YFV-C : SSOP-B8
BA2903YFVM-C : MSOP8
(Top View)
OUT1
- IN1
+IN1
VEE
1
2
3
7
5
4
1
OUT1
2
-IN1
3
+IN1
4
VEE
5
+IN2
OUT2
- IN2
6
CH2
Symbol
VCC
8
CH1
Pin No.
6
-IN2
7
OUT2
8
VCC
Pin No.
Symbol
1
OUT2
2
OUT1
3
VCC
+ IN2
BA2901YF-C : SOP14
BA2901YFV-C : SSOP-B14
(Top View)
1
14
OUT3
OUT1 2
13
OUT4
VCC
3
12
VEE
- IN1
4
+IN1
5
OUT2
- IN2
6
+IN2
7
CH1
CH2
CH4
CH3
11
+IN4
10
- IN4
9
+IN3
8
- IN3
4
-IN1
5
+IN1
6
-IN2
7
+IN2
8
-IN3
9
+IN3
10
-IN4
11
+IN4
12
VEE
13
OUT4
14
OUT3
Package
SOP8
SSOP-B8
MSOP8
SOP14
SSOP-B14
BA2903YF-C
BA2903YFV-C
BA2903YFVM-C
BA2901YF-C
BA2901YFV-C
www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
2/29
TSZ02201-0RFR1G200120-1-2
11.Mar.2013 Rev.003
Datasheet
BA2903Yxxx-C, BA2901Yxx-C
●Ordering Information
B
A
2
9
0
x
Y
x
x
x
-
C
Package
F
: SOP8
SOP14
FV : SSOP-B8
: SSOP-B14
FVM : MSOP8
Part Number
BA2903Yxxx
BA2901Yxx
x
x
Packaging and forming specification
C: Automotive (engine control unit,
electric power steering, antilock
braking system, etc.)
E2: Embossed tape and reel
(SOP8/SOP14/SSOP-B8/
SSOP-B14)
TR: Embossed tape and reel
(MSOP8)
●Line-up
Operating
Supply
Voltage
Topr
Dual/Quad
Dual
-40℃ to +125℃
+2.0V ~ +36V
Orderable
Part Number
Package
SOP8
Reel of 2500
BA2903YF-CE2
SSOP-B8
Reel of 2500
BA2903YFV-CE2
MSOP8
Reel of 3000
BA2903YFVM-CTR
SOP14
Reel of 2500
BA2901YF-CE2
SSOP-B14
Reel of 2500
BA2901YFV-CE2
Quad
●Absolute Maximum Ratings (Ta=25℃)
Parameter
Symbol
Supply Voltage
VCC-VEE
Power dissipation
Differential Input Voltage
Pd
*7
Input Common-mode Voltage Range
Input Current
*8
Ratings
Unit
+36
V
SOP8
775*1*6
SSOP-B8
625
MSOP8
600
SOP14
560*4*6
SSOP-B14
870*5*6
*2*6
*3*6
mW
Vid
+36
V
Vicm
(VEE-0.3) to (VEE+36)
V
Ii
-10
mA
Operating Temperature Range
Topr
-40 to +125
℃
Storage Temperature Range
Tstg
-55 to +150
℃
Tjmax
+150
℃
Maximum junction Temperature
Note : Absolute maximum rating item indicates the condition which must not be exceeded.
Application if voltage in excess of absolute maximum rating or use out of absolute maximum rated temperature environment may cause
deterioration of characteristics.
*1 To use at temperature above Ta＝25℃ reduce 6.2mW/℃.
*2 To use at temperature above Ta＝25℃ reduce 5.5mW/℃.
*3 To use at temperature above Ta＝25℃ reduce 4.8mW/℃.
*4 To use at temperature above Ta＝25℃ reduce 4.9mW/℃.
*5 To use at temperature above Ta＝25℃ reduce 7.0mW/℃.
*6 Mounted on a FR4 glass epoxy PCB(70mm×70mm×1.6mm).
*7 The voltage difference between inverting input and non-inverting input is the differential input voltage.
Then input terminal voltage is set to more than VEE.
*8 Excessive input current will flow if a differential input voltage in excess of approximately 0.6V is applied between
the input unless some limiting resistance is used.
www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
3/29
TSZ02201-0RFR1G200120-1-2
11.Mar.2013 Rev.003
Datasheet
BA2903Yxxx-C, BA2901Yxx-C
Electrical Characteristics
○BA2903Yxxx-C (Unless otherwise specified VCC=+5V, VEE=0V)
Limits
Temperature
Parameter
Symbol
range
Min.
Typ.
25℃
2
*9
Input Offset Voltage
Vio
Full range
25℃
5
*9
Input Offset Current
Iio
Full range
25℃
50
*9
Input Bias Current
Ib
Full range
25℃
0
Input Common-mode
Vicm
Voltage Range
Full range
0
25℃
88
100
Large Signal Voltage Gain
Av
Full range
74
25℃
0.6
Supply Current
ICC
Full range
*10
Output Sink Current
Isink
25℃
6
16
25℃
150
Output Saturation Voltage
VOL
(Low level output voltage)
Full range
25℃
0.1
Output Leakage Current
Ileak
(High level output current)
Full range
Response Time
Operable Frequency
Tre
Fopr
Max.
4
5
40
50
250
275
VCC-1.5
VCC-2.0
1
2.5
400
700
1
-
1.3
-
-
0.4
-
100
-
-
Conditions
mV
OUT=1.4V
VCC=5～36V,OUT=1.4V
nA
OUT=1.4V
nA
OUT=1.4V
V
dB
mA
mA
mV
μA
μs
25℃
25℃
Unit
kHz
VCC=15V, OUT=1.4～11.4V
RL=15kΩ, VRL=15V
OUT=open
OUT=open, VCC=36V
VIN+=0V, VIN-=1V, VOL=1.5V
VIN+=0V, VIN-=1V,
Isink=4mA
VIN+=1V, VIN-=0V, VOH=5V
VIN+=1V, VIN-=0V, VOH=36V
RL=5.1kΩ, VRL=5V
VIN=100mVP-P, overdrive=5mV
RL=5.1kΩ, VRL=5V, VIN=TTL
Logic Swing, VREF=1.4V
VCC=5V, RL=2kΩ, VIN+=1.5V,VIN-=5Vp-p
(Duty 50% Rectangular Pulse)
*9 Absolute value
*10 Under high temperatures, please consider the power dissipation when selecting the output current.
When the output terminal is continuously shorted the output current reduces the internal temperature by flushing.
○BA2901Yxx-C (Unless otherwise specified VCC=+5V, VEE=0V)
Limits
Temperature
Parameter
Symbol
range
Min.
Typ.
25℃
2
*11
Input Offset Voltage
Vio
Full range
25℃
5
*11
Input Offset Current
Iio
Full range
25℃
50
*11
Input Bias Current
Ib
Full range
25℃
0
Input Common-mode
Vicm
Voltage Range
Full range
0
25℃
88
100
Large Signal Voltage Gain
Av
Full range
74
25℃
0.8
Supply Current
ICC
Full range
*12
Output Sink Current
Isink
25℃
6
16
25℃
150
Output Saturation Voltage
VOL
(Low level output voltage)
Full range
25℃
0.1
Output Leakage Current
Ileak
(High level output current)
Full range
Response Time
Operable Frequency
Tre
Fopr
Max.
4
5
40
50
250
275
VCC-1.5
VCC-2.0
2
2.5
400
700
1
-
1.3
-
-
0.4
-
100
-
-
Conditions
mV
OUT=1.4V
VCC=5～36V,OUT=1.4V
nA
OUT=1.4V
nA
OUT=1.4V
V
dB
mA
mA
mV
μA
μs
25℃
25℃
Unit
kHz
VCC=15V, OUT=1.4～11.4V
RL=15kΩ, VRL=15V
OUT=open
OUT=open, VCC=36V
VIN+=0V, VIN-=1V, VOL=1.5V
VIN+=0V, VIN-=1V,
Isink=4mA
VIN+=1V, VIN-=0V, VOH=5V
VIN+=1V, VIN-=0V, VOH=36V
RL=5.1kΩ, VRL=5V
VIN=100mVP-P, overdrive=5mV
RL=5.1kΩ, VRL=5V, VIN=TTL
Logic Swing, VREF=1.4V
VCC=5V, RL=2kΩ, VIN+=1.5V,VIN-=5Vp-p
(Duty 50% Rectangular Pulse)
*11 Absolute value
*12 Under high temperatures, please consider the power dissipation when selecting the output current.
When the output terminal is continuously shorted the output current reduces the internal temperature by flushing.
www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
4/29
TSZ02201-0RFR1G200120-1-2
11.Mar.2013 Rev.003
Datasheet
BA2903Yxxx-C, BA2901Yxx-C
Description of Electrical Characteristics
Described below are descriptions of the relevant electrical terms used in this datasheet. Items and symbols used are also
shown. Note that item name and symbol and their meaning may differ from those on another manufacturer’s document or
general document.
1. Absolute maximum ratings
Absolute maximum rating items indicate the condition which must not be exceeded. Application of voltage in excess of absolute
maximum rating or use out of absolute maximum rated temperature environment may cause deterioration of characteristics.
1.1 Power supply voltage (VCC-VEE)
Indicates the maximum voltage that can be applied between the positive power supply terminal and negative power
supply terminal without deterioration or destruction of characteristics of internal circuit.
1.2 Differential input voltage (Vid)
Indicates the maximum voltage that can be applied between non-inverting and inverting terminals without damaging
the IC.
1.3 Input common-mode voltage range (Vicm)
Indicates the maximum voltage that can be applied to the non-inverting and inverting terminals without deterioration
or destruction of electrical characteristics. Input common-mode voltage range of the maximum ratings does not assure
normal operation of IC. For normal operation, use the IC within the input common-mode voltage range characteristics.
1.4 Operating and storage temperature ranges (Topr,Tstg)
The operating temperature range indicates the temperature range within which the IC can operate. The higher the
ambient temperature, the lower the power consumption of the IC. The storage temperature range denotes the range
of temperatures the IC can be stored under without causing excessive deterioration of the electrical characteristics.
1.5 Power dissipation (Pd)
Indicates the power that can be consumed by the IC when mounted on a specific board at the ambient temperature 25℃
(normal temperature). As for package product, Pd is determined by the temperature that can be permitted by the IC in
the package (maximum junction temperature) and the thermal resistance of the package.
2.Electrical characteristics
2.1 Input offset voltage (Vio)
Indicates the voltage difference between non-inverting terminal and inverting terminals. It can be translated into the
input voltage difference required for setting the output voltage at 0 V.
2.2 Input offset current (Iio)
Indicates the difference of input bias current between the non-inverting and inverting terminals.
2.3 Input bias current (Ib)
Indicates the current that flows into or out of the input terminal. It is defined by the average of input bias currents at
the non-inverting and inverting terminals.
2.4 Input common-mode voltage range (Vicm)
Indicates the input voltage range where IC normally operates.
2.5 Large signal voltage gain (Av)
Indicates the amplifying rate (gain) of output voltage against the voltage difference between non-inverting terminal
and inverting terminal. It is normally the amplifying rate (gain) with reference to DC voltage.
Av = (Output voltage) / (Differential input voltage)
2.6 Circuit current (ICC)
Indicates the current that flows within the IC under specified no-load conditions.
2.7 Output sink current (Isink)
Indicates the current flowing into the IC under specific output conditions.
2.8 Output saturation voltage ( Low level output voltage) (VOL)
Indicates the lower limit of output voltage under specific input and output conditions.
2.9 Output leakage current( High level output current) (Ileak)
Indicates the current that flows into the IC under specific input and output conditions.
2.11 Response Time (Tre)
Indicates the time interval between the application of input and output conditions.
2.10 Operable Frequency (Fopr)
Indicates minimum frequency that IC moves under specific conditions..
www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
5/29
TSZ02201-0RFR1G200120-1-2
11.Mar.2013 Rev.003
Datasheet
BA2903Yxxx-C, BA2901Yxx-C
●Typical Performance Curves
○BA2903Yxxx-C
1. 6
.
1000
SUPPLY CURRENT [mA]
POWER DISSIPATION [mW]
BA2903YF-C
800
BA2903YFV-C
600
BA2903YFVM-C
400
200
0
1. 4
1. 2
1. 0
-40℃
0. 8
0. 6
25℃
0. 4
125℃
0. 2
0. 0
0
25
50
75
100
125
150
0
AMBIENT TEMPERATURE [℃]
MAXIMUM OUTPUT VOLTAGE [mV]
SUPPLY CURRENT [mA]
1.4
1.2
1.0
36V
2V
0.6
0.4
0.2
0.0
-50
-25
0
25
50
30
40
Figure 3.
Supply Current – Supply Voltage
1.6
5V
20
SUPPLY VOLTAGE [V]
Figure 2.
Derating Curve
0.8
10
75
100 125 150
200
150
125℃
100
25℃
50
-40℃
0
0
AMBIENT TEMPERATURE [℃]
10
20
30
40
SUPPLY VOLTAGE [V]
Figure 5.
Maximum Output Voltage – Supply Voltage
(Isink=4mA)
Figure 4.
Supply Current – Ambient
Temperature
(*)The data above is measurement value of typical sample, it is not guaranteed.
www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
6/29
TSZ02201-0RFR1G200120-1-2
11.Mar.2013 Rev.003
Datasheet
BA2903Yxxx-C, BA2901Yxx-C
200
2
1.8
2V
OUTPUT VOLTAGE [V]
MAXIMUM OUTPUT VOLTAGE [mV]
○BA2903Yxxx-C
150
100
5V
36V
50
1.6
1.4
125℃
1.2
1
25℃
0.8
0.6
0.4
-40℃
0.2
0
0
-50 -25
0
25
50
75
0
100 125 150
2
AMBIENT TEMPERATURE [℃]
6
8
10
12
14
16
18
20
OUTPUT SINK CURRENT [mA]
Figure 7.
Output Voltage – Output Sink Current
(VCC=5V)
Figure 6.
Maximum Output Voltage – Ambient Temperature
(Isink=4mA)
8
30
5V
INPUT OFFSET VOLTAGE [mV]
40
OUTPUT SINK CURRENT [mA]
4
36V
20
2V
10
6
4
-40℃
2
0
25℃
125℃
-2
-4
-6
-8
0
-50
-25
0
25
50
75
100 125 150
0
AMBIENT TEMPERATURE [℃]
10
20
30
40
SUPPLY VOLTAGE [V]
Figure 8.
Output Sink Current – Ambient Temperature
(OUT=1.5V)
Figure 9.
Input Offset Voltage – Supply Voltage
(*)The data above is measurement value of typical sample, it is not guaranteed.
www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
7/29
TSZ02201-0RFR1G200120-1-2
11.Mar.2013 Rev.003
Datasheet
BA2903Yxxx-C, BA2901Yxx-C
8
160
6
140
4
5V
INPUT BIAS CURRENT [nA]
INPUT OFFSET VOLTAGE [mV]
○BA2903Yxxx-C
36V
2
0
2V
-2
-4
-6
120
-40℃
100
80
60
25℃
40
125℃
20
0
-8
-50
-25
0
25
50
75
0
100 125 150
5
AMBIENT TEMPERATURE [℃]
20
25
30
35
Figure 11.
Input Bias Current – Supply Voltage
160
50
140
40
INPUT OFFSET CURRENT[nA]
INPUT BIAS CURRENT [nA]
15
SUPPLY VOLTAGE [V]
Figure 10.
Input Offset Voltage – Ambient
Temperature
120
100
36V
80
60
40
5V
2V
20
10
30
20
-40℃
10
0
-10
125℃
25℃
-20
-30
-40
-50
0
-50
-25
0
25
50
75
100 125 150
0
10
20
30
40
SUPPLY VOLTAGE [V]
AMBIENT TEMPERATURE [℃]
Figure 13.
Input Offset Current – Supply Voltage
Figure 12.
Input Bias Current – Ambient Temperature
(*)The data above is measurement value of typical sample, it is not guaranteed.
www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
8/29
TSZ02201-0RFR1G200120-1-2
11.Mar.2013 Rev.003
Datasheet
BA2903Yxxx-C, BA2901Yxx-C
○BA2903Yxxx-C
LARGE SINGAL VOLTAGE GAIN [dB]
INPUT OFFSET CURRENT [nA]
50
40
30
20
2V
10
5V
0
-10
36V
-20
-30
-40
-50
-50
-25
0
25
50
75
140
130
125℃
25℃
120
110
100
-40℃
90
80
70
60
100 125 150
0
10
AMBIENT TEMPERATURE [℃]
COMMON MODE REJECTION RATIO [dB]
LARGE SINGAL VOLTAGE GAIN [dB]
130
36V
110
15V
5V
90
80
70
60
-50
-25
0
25
50
75
40
Figure 15.
Large Signal Voltage Gain
– Supply Voltage
140
100
30
SUPPLY VOLTAGE [V]
Figure 14.
Input Offset Current
– Ambient Temperature
120
20
100 125 150
160
140
120
125℃
100
80
-40℃
25℃
60
40
0
AMBIENT TEMPERATURE [℃]
10
20
30
40
SUPPLY VOLTAGE [V]
Figure 16.
Large Signal Voltage Gain
– Ambient Temperature
Figure 17.
Common Mode Rejection Ratio
– Supply Voltage
(*)The data above is measurement value of typical sample, it is not guaranteed.
www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
9/29
TSZ02201-0RFR1G200120-1-2
11.Mar.2013 Rev.003
Datasheet
BA2903Yxxx-C, BA2901Yxx-C
6
150
INPUT OFFSET VOLTAGE [mV]
COMMON MODE REJECTION RATIO [dB]
○BA2903Yxxx-C
125
36V
100
75
5V
2V
50
25
-40℃
4
25℃
125℃
2
0
-2
-4
-6
0
-50
-25
0
25
50
75
-1
100 125 150
1
2
3
4
5
INPUT VOLTAGE [V]
AMBIENT TEMPERATURE [℃]
Figure 18.
Common Mode Rejection Ratio
– Ambient Temperature
Figure 19.
Input Offset Voltage – Input Voltage
(VCC=5V)
200
5
RESPONSE TIME (LOW TO HIGH)[us]
POWER SUPPLY REJECTION RATIO [dB]
0
180
160
140
120
100
80
60
-50
-25
0
25
50
75
100 125 150
4
3
2
125℃
25℃
-40℃
1
0
-100
-80
-60
-40
-20
0
OVER DRIVE VOLTAGE [mV]
AMBIENT TEMPERATURE [℃]
Figure 21.
Response Time (Low to High) – Over Drive Voltage
(VCC=5V, VRL=5V, RL=5.1kΩ)
Figure 20.
Power Supply Rejection Ratio
– Ambient Temperature
(*)The data above is measurement value of typical sample, it is not guaranteed.
www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
10/29
TSZ02201-0RFR1G200120-1-2
11.Mar.2013 Rev.003
Datasheet
BA2903Yxxx-C, BA2901Yxx-C
○BA2903Yxxx-C
10
RESPONSE TIME (HIGH TO LOW)[us]
RESPONSE TIME (LOW TO HIGH)[us]
5
4
3
5mV
overdrive
20mV
overdrive
100mV
2
overdrive
1
0
8
6
4
125℃
25℃
-40℃
2
0
-50
-25
0
25
50
75
100 125 150
0
20
40
60
80
100
OVER DRIVE VOLTAGE [mV]
AMBIENT TEMPERATURE [℃]
Figure 22.
Response Time (Low to High)
– Ambient Temperature (VCC=5V, VRL=5V,
RL=5.1kΩ)
Figure 23.
Response Time (High to Low)
– Over Drive Voltage
(VCC=5V, VRL=5V, RL=5.1kΩ)
RESPONSE TIME (HIGH TO LOW)[us]
10
8
6
5mV
overdrive
20mV
4
overdrive
100mV
overdrive
2
0
-50
-25
0
25
50
75
100 125 150
AMBIENT TEMPERATURE [℃]
Figure 24.
Response Time (High to Low)
– Ambient Temperature
(VCC=5V, VRL=5V, RL=5.1kΩ)
(*)The data above is measurement value of typical sample, it is not guaranteed.
www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
11/29
TSZ02201-0RFR1G200120-1-2
11.Mar.2013 Rev.003
Datasheet
BA2903Yxxx-C, BA2901Yxx-C
○BA2901Yxx-C
2.0
SUPPLY CURRENT [mA]
POWER DISSIPATION [mW]
1000
800
BA2901YFV-C
600
BA2901YF-C
400
200
0
0
25
50
75
100
125
-40℃
1.5
1.0
25℃
0.5
125℃
0.0
150
0
10
AMBIENT TEMPERATURE [℃]
36V
5V
2V
0.5
0.0
0
25
50
75
100 125 150
MAXIMUM OUTPUT VOLTAGE [mV]
SUPPLY CURRENT [mA]
1.5
-25
40
Figure 26.
Supply Current – Supply Voltage
2.0
-50
30
SUPPLY VOLTAGE [V]
Figure 25.
Derating Curve
1.0
20
200
150
125℃
100
25℃
50
-40℃
0
0
10
AMBIENT TEMPERATURE [℃]
20
30
40
SUPPLY VOLTAGE [V]
Figure 27.
Supply Current – Ambient Temperature
Figure 28.
Maximum Output Voltage – Supply Voltage
(Isink=4mA)
(*)The data above is measurement value of typical sample, it is not guaranteed.
www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
12/29
TSZ02201-0RFR1G200120-1-2
11.Mar.2013 Rev.003
Datasheet
BA2903Yxxx-C, BA2901Yxx-C
200
2
1.8
2V
OUTPUT VOLTAGE [V]
MAXIMUM OUTPUT VOLTAGE [mV]
○BA2901Yxx-C
150
100
5V
36V
50
1.6
1.4
125℃
1.2
1
25℃
0.8
0.6
0.4
-40℃
0.2
0
0
-50 -25
0
25
50
75
0
100 125 150
2
AMBIENT TEMPERATURE [℃]
6
8
10
12
14
16
18
20
OUTPUT SINK CURRENT [mA]
Figure 30.
Output Voltage – Output Sink Current
(VCC=5V)
Figure 29.
Maximum Output Voltage – Ambient Temperature
(Isink=4mA)
8
30
5V
INPUT OFFSET VOLTAGE [mV]
40
OUTPUT SINK CURRENT [mA]
4
36V
20
2V
10
6
4
-40℃
2
0
25℃
125℃
-2
-4
-6
-8
0
-50
-25
0
25
50
75
100 125 150
0
AMBIENT TEMPERATURE [℃]
10
20
30
40
SUPPLY VOLTAGE [V]
Figure 31.
Output Sink Current – Ambient Temperature
(OUT=1.5V)
Figure 32.
Input Offset Voltage – Supply Voltage
(*)The data above is measurement value of typical sample, it is not guaranteed.
www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
13/29
TSZ02201-0RFR1G200120-1-2
11.Mar.2013 Rev.003
Datasheet
BA2903Yxxx-C, BA2901Yxx-C
8
160
6
140
4
5V
INPUT BIAS CURRENT [nA]
INPUT OFFSET VOLTAGE [mV]
○BA2901Yxx-C
36V
2
0
2V
-2
-4
-6
120
-40℃
100
80
60
25℃
40
125℃
20
0
-8
-50
-25
0
25
50
75
0
100 125 150
5
AMBIENT TEMPERATURE [℃]
20
25
30
35
Figure 34.
Input Bias Current – Supply Voltage
160
50
140
40
INPUT OFFSET CURRENT[nA]
INPUT BIAS CURRENT [nA]
15
SUPPLY VOLTAGE [V]
Figure 33.
Input Offset Voltage – Ambient
Temperature
120
100
36V
80
60
40
5V
2V
20
10
30
20
-40℃
10
0
-10
125℃
25℃
-20
-30
-40
-50
0
-50
-25
0
25
50
75
100 125 150
0
10
20
30
40
SUPPLY VOLTAGE [V]
AMBIENT TEMPERATURE [ ℃]
Figure 36.
Input Offset Current – Supply Voltage
Figure 35.
Input Bias Current – Ambient Temperature
(*)The data above is measurement value of typical sample, it is not guaranteed.
www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
14/29
TSZ02201-0RFR1G200120-1-2
11.Mar.2013 Rev.003
Datasheet
BA2903Yxxx-C, BA2901Yxx-C
○BA2901Yxx-C
LARGE SINGAL VOLTAGE GAIN [dB]
INPUT OFFSET CURRENT [nA]
50
40
30
20
2V
10
5V
0
-10
36V
-20
-30
-40
-50
-50
-25
0
25
50
75
140
130
125℃
25℃
120
110
100
-40℃
90
80
70
60
100 125 150
0
10
AMBIENT TEMPERATURE [ ℃]
COMMON MODE REJECTION RATIO [dB]
LARGE SINGAL VOLTAGE GAIN [dB]
130
36V
110
15V
5V
90
80
70
60
-50
-25
0
25
50
75
40
Figure 38.
Large Signal Voltage Gain
– Supply Voltage
140
100
30
SUPPLY VOLTAGE [V]
Figure 37.
Input Offset Current
– Ambient Temperature
120
20
100 125 150
160
140
120
125℃
100
80
-40℃
25℃
60
40
0
AMBIENT TEMPERATURE [℃]
10
20
30
40
SUPPLY VOLTAGE [V]
Figure 39.
Large Signal Voltage Gain
– Ambient Temperature
Figure 40.
Common Mode Rejection Ratio
– Supply Voltage
(*)The data above is measurement value of typical sample, it is not guaranteed.
www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
15/29
TSZ02201-0RFR1G200120-1-2
11.Mar.2013 Rev.003
Datasheet
BA2903Yxxx-C, BA2901Yxx-C
6
150
INPUT OFFSET VOLTAGE [mV]
COMMON MODE REJECTION RATIO [dB]
○BA2901Yxx-C
125
36V
100
75
5V
2V
50
25
-40℃
4
25℃
125℃
2
0
-2
-4
-6
0
-50
-25
0
25
50
75
-1
100 125 150
0
2
3
4
5
INPUT VOLTAGE [V]
AMBIENT TEMPERATURE [℃]
Figure 41.
Common Mode Rejection Ratio
– Ambient Temperature
Figure 42.
Input Offset Voltage – Input Voltage
(VCC=5V)
200
5
RESPONSE TIME (LOW TO HIGH)[us]
POWER SUPPLY REJECTION RATIO [dB]
1
180
160
140
120
100
80
60
-50
-25
0
25
50
75
100 125 150
4
3
2
25℃
-40℃
125℃
1
0
-100
-80
-60
-40
-20
0
OVER DRIVE VOLTAGE [mV]
AMBIENT TEMPERATURE [ ℃]
Figure 44.
Response Time (Low to High) – Over Drive Voltage
(VCC=5V, VRL=5V, RL=5.1kΩ)
Figure 43.
Power Supply Rejection Ratio
– Ambient Temperature
(*)The data above is measurement value of typical sample, it is not guaranteed.
www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
16/29
TSZ02201-0RFR1G200120-1-2
11.Mar.2013 Rev.003
Datasheet
BA2903Yxxx-C, BA2901Yxx-C
○BA2901Yxx-C
10
RESPONSE TIME (HIGH TO LOW)[us]
RESPONSE TIME (LOW TO HIGH)[us]
5
4
3
5mV
overdrive
20mV
overdrive
100mV
2
overdrive
1
0
-50
-25
0
25
50
75
8
6
4
125℃
25℃
-40℃
2
0
100 125 150
0
20
40
60
80
100
OVER DRIVE VOLTAGE [mV]
AMBIENT TEMPERATURE [℃]
Figure 45.
Response Time (Low to High)
– Ambient Temperature (VCC=5V, VRL=5V,
RL=5.1kΩ)
Figure 46.
Response Time (High to Low)
– Over Drive Voltage
(VCC=5V, VRL=5V, RL=5.1kΩ)
RESPONSE TIME (HIGH TO LOW)[us]
10
8
6
5mV
overdrive
20mV
4
overdrive
100mV
overdrive
2
0
-50
-25
0
25
50
75
100 125 150
AMBIENT TEMPERATURE [℃]
Figure 47.
Response Time (High to Low)
– Ambient Temperature
(VCC=5V, VRL=5V, RL=5.1kΩ)
(*)The data above is measurement value of typical sample, it is not guaranteed.
www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
17/29
TSZ02201-0RFR1G200120-1-2
11.Mar.2013 Rev.003
Datasheet
BA2903Yxxx-C, BA2901Yxx-C
●Power Dissipation
Power dissipation (total loss) indicates the power that the IC can consume at Ta=25°C (normal temperature). As the IC
consumes power, it heats up, causing its temperature to be higher than the ambient temperature. The allowable
temperature that the IC can accept is limited. This depends on the circuit configuration, manufacturing process, and
consumable power.
Power dissipation is determined by the allowable temperature within the IC (maximum junction temperature) and the
thermal resistance of the package used (heat dissipation capability). Maximum junction temperature is typically equal to the
maximum storage temperature. The heat generated through the consumption of power by the IC radiates from the mold
resin or lead frame of the package. Thermal resistance, represented by the symbol θja°C/W, indicates this heat dissipation
capability. Similarly, the temperature of an IC inside its package can be estimated by thermal resistance.
Figure 50. (a) shows the model of the thermal resistance of the package. The equation below shows how to compute for the
Thermal resistance (θja), given the ambient temperature (Ta), junction temperature (Tj), and power dissipation (Pd).
θja = (Tjmax-Ta) / Pd
℃/W
・・・・・
(Ⅰ)
The Derating curve in Figure 48. (b) indicates the power that the IC can consume with reference to ambient temperature.
Power consumption of the IC begins to attenuate at certain temperatures. This gradient is determined by Thermal
resistance (θja), which depends on the chip size, power consumption, package, ambient temperature, package condition,
wind velocity, etc. This may also vary even when the same of package is used. Thermal reduction curve indicates a
reference value measured at a specified condition. Figure 49. (c),(d) shows an example of the derating curve for
BA2903Yxxx-C, BA2901Yxx-C.
LSIの 消 費
力 [W]
Power dissipation
of 電
LSI
Pd (max)
θja=(Tjmax-Ta)/Pd ℃/W
θja2 < θja1
P2
周囲温度 Ta [℃]
Ambient temperature
θ' ja2
P1
θ ja2
Tj ' (max) Tj (max)
θ' ja1
θ ja1
Chip surfaceチップ
temperature
表面温度 Tj [℃]
0
消費電力Pd
P [W]
Power dissipation
[W]
25
50
75
100
125
150
Ambient temperature
周 囲 温 度 Ta [℃ ]
(a) Thermal resistance
(b) Derating curve
Figure 48. Thermal resistance and derating
1000
1000
POWER DISSIPATION [mW]
POWER DISSIPATION [mW]
BA2903YF-C(*13)
800
BA2903YFV-C(*14)
600
BA2903YFVM-C(*15)
400
200
0
0
25
50
75
100
125
BA2901YFV-C(*16)
800
600
BA2901YF-C(*17)
400
200
0
150
0
AMBIENT TEMPERATURE [℃]
25
50
75
100
125
150
AMBIENT TEMPERATURE [℃]
(c) BA2903Y
(d) BA2901Y
(*13)
(*14)
(*15)
(*16)
(*17)
UNIT
6.2
5.0
4.8
7.0
4.5
mW/℃
When using the unit above Ta=25℃, subtract the value above per degree℃.
Permissible dissipation is the value when FR4 glass epoxy board 70mm×70mm×1.6mm(cooper foil area below 3%) is mounted.
Figure 49. Derating curve
www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
18/29
TSZ02201-0RFR1G200120-1-2
11.Mar.2013 Rev.003
Datasheet
BA2903Yxxx-C, BA2901Yxx-C
●Application Information
NULL method condition for Test circuit1
VCC,VEE,EK,Vicm Unit：V
Parameter
VF
S1
S2
S3
Vcc
VEE
EK
Vicm
Calculation
Input Offset Voltage
VF1
ON
ON
ON
5～36
0
-1.4
0
1
Input Offset Current
VF2
OFF
OFF
ON
5
0
-1.4
0
2
VF3
OFF
ON
VF4
ON
OFF
ON
ON
Input Bias Current
VF5
Large Signal Voltage Gain
VF6
ON
ON
5
0
-1.4
0
5
0
-1.4
0
15
0
-1.4
0
15
0
-11.4
0
3
4
- Calculation 1. Input Offset Voltage (Vio)
Vio 
VF1
1+ RF / RS
[V]
2. Input Offset Current (Iio)
Iio 
VF2 - VF1
Ri × (1 + RF / RS)
[A]
3. Input Bias Current (Ib)
Ib 
VF4 - VF3
2 × Ri × (1 + RF / RS)
[A]
4. Large Signal Voltage Gain (Av)
Av  20 × Log
ΔEK × (1+ RF/RS)
VF5 - VF6
[dB]
RF=50kΩ
500kΩ
VCC
SW1
0.1μF
EK
+15V
RS=50Ω
Ri=10kΩ
Ri=10kΩ
500kΩ
DUT
NULL
SW3
RS=50Ω
Vicm
1000pF
V
RL
SW2
50kΩ
VF
VEE
-15V
Figure 50. Test circuit1 (one channel only)
www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
19/29
TSZ02201-0RFR1G200120-1-2
11.Mar.2013 Rev.003
Datasheet
BA2903Yxxx-C, BA2901Yxx-C
Switch Condition for Test Circuit 2
SW No.
Supply Current
SW
1
SW
2
SW
3
SW
4
SW
5
SW
6
SW
7
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Output Sink Current
VOL=1.5V
OFF
ON
ON
OFF
OFF
OFF
ON
Output Saturation Voltage
Isink=4mA
OFF
ON
ON
OFF
ON
ON
OFF
Output Leakage Current
VOH=36V
OFF
ON
ON
OFF
OFF
OFF
ON
Response Time
RL=5.1kΩ, VRL=5V
ON
OFF
ON
ON
OFF
OFF
OFF
VCC
A
－
＋
SW1
SW2
SW4
SW3
VEE
VIN-
SW5
SW6
RL
SW7
V
A
VRL
VIN+
VOL/VOH
Figure 51. Test Circuit 2 (one channel only)
Input wave
VIN
Input wave
入力電圧波形
VIN
入力電圧波形
+100mV
0V
overdrive voltage
overdrive voltage
0V
VOUT
-100mV
Output wave
VOUT
出力電圧波形
VCC
Output wave
出力電圧波形
VCC
VCC/2
VCC/2
0V
0V
Tre (LOW to HIGH)
Tre (HIGH to LOW)
Figure 52. Response Time
www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
20/29
TSZ02201-0RFR1G200120-1-2
11.Mar.2013 Rev.003
Datasheet
BA2903Yxxx-C, BA2901Yxx-C
Example of circuit
○Reference voltage is VinVoltage
電圧
Pull Up
VCC
Reference voltage
基準電圧
+
Vin
Time
時間
Vref
Reference Voltage
VEE
Voltage
Input voltage wave
入力電圧波形
電圧
High
While the input voltage is higher that the reference
voltage, the output voltage remains high. In case
the input voltage becomes lower than the reference
voltage, the output voltage will turn low.
Low
Time
Output voltage wave
出力電圧波形
○Reference voltage is Vin+
Voltage
電圧
VCC
Pull Up
Reference voltage
基準電圧
+
-
Vref
Reference Voltage
Vin
Time
時間
VEE
Voltage
Input voltage wave
入力電圧波形
High
While the input voltage is smaller that the reference
voltage, the output voltage remains high. In case
the input voltage becomes higher than the
reference voltage, the output voltage will turn low.
Low
Time
Output voltage wave
www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
21/29
TSZ02201-0RFR1G200120-1-2
11.Mar.2013 Rev.003
Datasheet
BA2903Yxxx-C, BA2901Yxx-C
●Operational Notes
1) Unused circuits
When there are unused comparators, it is recommended that they are
connected as in Figure 53. , setting the non-inverting input terminal to a
potential within the in-phase input voltage range (Vicm).
VCC
Vicm
Please keep this potential in Vicm
VCC-1.5V＞Vicm＞VEE
2) Input voltage
Applying VEE +36V to the input terminal is possible without causing
deterioration of the electrical characteristics or destruction, regardless of
the supply voltage. However, this does not ensure normal circuit operation.
Please note that the circuit operates normally only when the input voltage is
within the common mode input voltage range of the electric characteristics.
+
-
OPEN
VEE
Figure 53. Disable circuit example
3) Power supply (single / dual)
The comparator operates when the voltage supplied is between VCC and VEE. Therefore, the signal supply comparator
can be used as a dual supply comparator as well.
4) Power dissipation Pd
Using the unit in excess of the rated power dissipation may cause deterioration in electrical characteristics including
reduced current capability due to the rise of chip temperature. Therefore, please take into consideration the power
dissipation (Pd) under actual operating conditions and apply a sufficient margin in thermal design. Refer to the thermal
derating curves for more information.
5) Short-circuit between pins and erroneous mounting
Be careful when mounting the IC on printed circuit boards. The IC may be damaged if it is mounted in a wrong orientation
or if pins are shorted together. Short circuit may be caused by conductive particles caught between the pins.
6) Terminal short-circuits
When the output and VCC terminals are shorted, excessive output current may flow, resulting in undue heat generation
and, subsequently, destruction.
7) Operation in a strong electromagnetic field
Operating the IC in the presence of a strong electromagnetic field may cause the IC to malfunction.
8) Radioactive rays
This IC is not designed protection against radioactive rays.
9) IC handling
Applying mechanical stress to the IC by deflecting or bending the board may cause fluctuations in the electrical
characteristics due to piezo resistance effects.
10) Board inspection
Connecting a capacitor to a pin with low impedance may stress the IC. Therefore, discharging the capacitor after every
process is recommended. In addition, when attaching and detaching the jig during the inspection phase, ensure that the
power is turned OFF before inspection and removal. Furthermore, please take measures against ESD in the assembly
process as well as during transportation and storage.
www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
22/29
TSZ02201-0RFR1G200120-1-2
11.Mar.2013 Rev.003
Datasheet
BA2903Yxxx-C, BA2901Yxx-C
●Marking Diagrams
SOP8(TOP VIEW)
SSOP-B8(TOP VIEW)
Part Number Marking
Part Number Marking
LOT Number
LOT Number
1PIN MARK
1PIN MARK
MSOP8(TOP VIEW)
SOP14(TOP VIEW)
Part Number Marking
Part Number Marking
LOT Number
LOT Number
1PIN MARK
1PIN MARK
SSOP-B14(TOP VIEW)
Part Number Marking
LOT Number
1PIN MARK
Product Name
BA2903Y
Marking
F-C
SOP8
2903Y
FV-C
SSOP-B8
MSOP8
03Y
FVM-C
BA2901Y
Package Type
2903Y
F-C
SOP14
BA2901YF
FV-C
SSOP-B14
2901Y
www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
23/29
TSZ02201-0RFR1G200120-1-2
11.Mar.2013 Rev.003
Datasheet
BA2903Yxxx-C, BA2901Yxx-C
●Physical Dimension, Tape and Reel Information
Package Name
SOP8
(Max 5.35 (include.BURR))
(UNIT : mm)
PKG : SOP8
Drawing No. : EX112-5001-1
<Tape and Reel information>
Tape
Embossed carrier tape
Quantity
2500pcs
Direction
of feed
E2
The direction is the 1pin of product is at the upper left when you hold
( reel on the left hand and you pull out the tape on the right hand
Direction of feed
1pin
Reel
∗ Order quantity needs to be multiple of the minimum quantity.
www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
)
24/29
TSZ02201-0RFR1G200120-1-2
11.Mar.2013 Rev.003
Datasheet
BA2903Yxxx-C, BA2901Yxx-C
●Physical Dimension, Tape and Reel Information
Package Name
SOP14
(Max 9.05 (include.BURR))
(UNIT : mm)
PKG : SOP14
Drawing No. : EX113-5001
<Tape and Reel information>
Tape
Embossed carrier tape
Quantity
2500pcs
Direction
of feed
E2
The direction is the 1pin of product is at the upper left when you hold
( reel on the left hand and you pull out the tape on the right hand
Direction of feed
1pin
Reel
∗ Order quantity needs to be multiple of the minimum quantity.
www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
)
25/29
TSZ02201-0RFR1G200120-1-2
11.Mar.2013 Rev.003
Datasheet
BA2903Yxxx-C, BA2901Yxx-C
●Physical Dimension, Tape and Reel Information
Package Name
SSOP-B8
<Tape and Reel information>
Tape
Embossed carrier tape
Quantity
2500pcs
Direction
of feed
E2
The direction is the 1pin of product is at the upper left when you hold
( reel on the left hand and you pull out the tape on the right hand
Direction of feed
1pin
Reel
∗ Order quantity needs to be multiple of the minimum quantity.
www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
)
26/29
TSZ02201-0RFR1G200120-1-2
11.Mar.2013 Rev.003
Datasheet
BA2903Yxxx-C, BA2901Yxx-C
●Physical Dimension, Tape and Reel Information
Package Name
SSOP-B14
<Tape and Reel information>
Tape
Embossed carrier tape
Quantity
2500pcs
Direction
of feed
E2
The direction is the 1pin of product is at the upper left when you hold
( reel on the left hand and you pull out the tape on the right hand
Direction of feed
1pin
Reel
∗ Order quantity needs to be multiple of the minimum quantity.
www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
)
27/29
TSZ02201-0RFR1G200120-1-2
11.Mar.2013 Rev.003
Datasheet
BA2903Yxxx-C, BA2901Yxx-C
●Physical Dimension, Tape and Reel Information
Package Name
MSOP8
<Tape and Reel information>
Tape
Embossed carrier tape
Quantity
3000pcs
Direction
of feed
TR
The direction is the 1pin of product is at the upper right when you hold
( reel on the left hand and you pull out the tape on the right hand
)
1pin
Direction of feed
Reel
∗ Order quantity needs to be multiple of the minimum quantity.
www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
28/29
TSZ02201-0RFR1G200120-1-2
11.Mar.2013 Rev.003
Datasheet
BA2903Yxxx-C, BA2901Yxx-C
●Land pattern data
MIE
b2
e
SOP8, SSOP-B8, MSOP8
SOP14, SSOP-B14
ℓ2
All dimensions in mm
Package
Land pitch
e
Land space
MIE
Land length
≧ℓ 2
Land width
b2
1.27
4.60
1.10
0.76
0.65
4.60
1.20
0.35
0.65
2.62
0.99
0.35
SOP8
SOP14
SSOP-B8
SSOP-B14
MSOP8
●Revision History
Date
Revision
Changes
11.Apr.2012
001
New Release
21.Jan.2013
002
Land pattern data inserted.
11.Mar.2013
003
Input offset voltage, Input offset current limit (Temp=25℃) changed.
Description of Physical Dimension, Tape and Reel Information changed.
www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
29/29
TSZ02201-0RFR1G200120-1-2
11.Mar.2013 Rev.003
Datasheet
Notice
General Precaution
1. Before you use our Products, you are requested to carefully read this document and fully understand its contents.
ROHM shall not be in any way responsible or liable for failure, malfunction or accident arising from the use of any
ROHM’s Products against warning, caution or note contained in this document.
2. All information contained in this document is current as of the issuing date and subject to change without any prior
notice. Before purchasing or using ROHM’s Products, please confirm the latest information with a ROHM sales
representative.
Precaution on using ROHM Products
1.
If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment,
aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life,
bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales
representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any
ROHM’s Products for Specific Applications.
2.
ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3.
Our Products are not designed under any special or extraordinary environments or conditions, as exemplified below.
Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the
use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our
Products under any special or extraordinary environments or conditions (as exemplified below), your independent
verification and confirmation of product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of
flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning
residue after soldering
[h] Use of the Products in places subject to dew condensation
4.
The Products are not subject to radiation-proof design.
5.
Please verify and confirm characteristics of the final or mounted products in using the Products.
6.
In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7.
De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual
ambient temperature.
8.
Confirm that operation temperature is within the specified range described in the product specification.
9.
ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Notice - Rev.004
© 2013 ROHM Co., Ltd. All rights reserved.
Datasheet
Precaution for Mounting / Circuit board design
1.
When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2.
In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the
ROHM representative in advance.
For details, please refer to ROHM Mounting specification
Precautions Regarding Application Examples and External Circuits
1.
If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the
characteristics of the Products and external components, including transient characteristics, as well as static
characteristics.
2.
You agree that application notes, reference designs, and associated data and information contained in this document
are presented only as guidance for Products use. Therefore, in case you use such information, you are solely
responsible for it and you must exercise your own independent verification and judgment in the use of such information
contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses
incurred by you or third parties arising from the use of such information.
Precaution for Electrostatic
This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper
caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be
applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,
isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).
Precaution for Storage / Transportation
1.
Product performance and soldered connections may deteriorate if the Products are stored in the places where:
[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2
[b] the temperature or humidity exceeds those recommended by ROHM
[c] the Products are exposed to direct sunshine or condensation
[d] the Products are exposed to high Electrostatic
2.
Even under ROHM recommended storage condition, solderability of products out of recommended storage time period
may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is
exceeding the recommended storage time period.
3.
Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads
may occur due to excessive stress applied when dropping of a carton.
4.
Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of
which storage time is exceeding the recommended storage time period.
Precaution for Product Label
QR code printed on ROHM Products label is for ROHM’s internal use only.
Precaution for Disposition
When disposing Products please dispose them properly using an authorized industry waste company.
Precaution for Foreign Exchange and Foreign Trade act
Since our Products might fall under controlled goods prescribed by the applicable foreign exchange and foreign trade act,
please consult with ROHM representative in case of export.
Precaution Regarding Intellectual Property Rights
1.
All information and data including but not limited to application example contained in this document is for reference
only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any
other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable
for infringement of any intellectual property rights or other damages arising from use of such information or data.:
2.
No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any
third parties with respect to the information contained in this document.
Notice - Rev.004
© 2013 ROHM Co., Ltd. All rights reserved.
Datasheet
Other Precaution
1.
The information contained in this document is provided on an “as is” basis and ROHM does not warrant that all
information contained in this document is accurate and/or error-free. ROHM shall not be in any way responsible or
liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or
concerning such information.
2.
This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.
3.
The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written
consent of ROHM.
4.
In no event shall you use in any way whatsoever the Products and the related technical information contained in the
Products or this document for any military purposes, including but not limited to, the development of mass-destruction
weapons.
5.
The proper names of companies or products described in this document are trademarks or registered trademarks of
ROHM, its affiliated companies or third parties.
Notice - Rev.004
© 2013 ROHM Co., Ltd. All rights reserved.