Frequently Asked Questions Rev C For Series: EC26 1. What is this oscillator series? This series of devices are oscillators where the output frequency is primarily controlled by an internal quartz bulk acoustic wave (BAW) crystal resonator and an integrated complementary metal-oxide semiconductor logic (CMOS) circuit. Utilizing a proprietary crystal resonator design and exclusive oscillator design techniques, this series of oscillators is calibrated to a specified frequency prior to shipment to the customer. 2. What are the typical customer circuit applications for this oscillator series? This oscillator series can be used in any of the following applications: 3. • Clock Recovery • Phase-Locked Loop and Frequency Synthesis • Synthesizer or System Reference • Clock Distribution • Clock Translation and Multiplexing What are the typical applications and end item products for this series? Here is a list of the common applications and products: • PCI Express • Gigabit Ethernet • Fiber Channel • SATA/SAS • FBDIMM, DDR, SONET, ATM, SDH • Routers, Servers, Hubs, and Network Switches • High Resolution Video, and Set-top Boxes • Scanners, Printers, Modems • LCD Displays and HDTV • Interface Controllers • Medical Equipment • PDAs and Portable Media Players • Digital Cameras and Gaming Products • Notebook Computers EC26 TEN10-005-002 Rev C Page 1 of 7 Ecliptek Frequently Asked Questions 4. • Video Cameras and Video Recorders • Portable Devices • Computer Peripherals and Networking Products What technical benefits does this product series offer? This series of crystal oscillator offers: • Improved frequency stability through the use of a bulk acoustic wave (BAW) quartz crystal resonator • Use of a fundamental and third overtone mode oscillator application specific integrated circuit (ASIC) design • Tight duty cycle option • Superior rms phase jitter and phase noise performance • Tri-state high impedance output • Low stand-by current • High speed complementary metal oxide semiconductor (CMOS) output with controlled rise and fall times • Industry standard ceramic four pad moisture sensitivity level 1 (MSL1) rated SMD packages • RoHS Compliant (Pb-free) with high temperature 260°C reflow capability 5. What are the construction characteristics of this product series? This product series consists of a single CMOS ASIC and a fundamental or third overtone mode BAW quartz crystal packaged inside a hermetically sealed ceramic leadless SMD package. The leadless SMD package has four gold plated contact I/O pads. The package has a seam sealed metal cover that is case grounded for improved EMI performance. 6. What is the input supply voltage for this product series? The nominal supply voltage and tolerance is provided on the datasheet. 7. What are the input current specifications for this product series? The input current specification is listed in milliamps as a maximum value and is provided on the datasheet. 8. What are the frequency stability and operating temperature range options for this product series? The available operating temperature range and frequency stability options can be found on the datasheet. 9. Does this series offer a tri-state output function? This product series offers a tri-state output function to facilitate the customer's use of in-process assembly testing or for the use of multiple clocks on the same node. It features a tri-state output control on pad one (1) where the output is three-stated (tri-state condition) when the voltage at the control pad is set to a logic low state. In this condition (see the figure below), the oscillator output buffer circuitry within the oscillator is shut down and the output pad is placed into a high impedance state. If the voltage at the control pad is set to no connect or a logic high state, the output is enabled (clocking). EC26 TEN10-005-002 Rev C Page 2 of 7 Ecliptek Frequently Asked Questions Note: The oscillator has an internal pull up resistor on the control pad. The series datasheet provides the VIH and VIL thresholds for control of the tri-state function. Figure: Tri-State Timing Diagram When entering the tri-state mode, the time from when the oscillator pad one input control reaches VIL and the oscillator output pad becomes high impedance is shown as tPLZ. When exiting the tri-state mode, the time from when the oscillator pad one input control reaches VOH and the oscillator output begins clocking is shown as tPZL. For this series, characterization test data indicates that tPLZ is typically 50nS and tPZL is typically less than 5mS. 10. Does this series offer a stand-by function? This oscillator series contains a stand-by function for power management. All active circuitry within the oscillator is shut down when the voltage at the control pad is set to a logic low state. In this condition, the output signal is three-stated (tri-state). The oscillator output gate becomes high impedance and the oscillator input current on the power supply line is negligible. The maximum stand-by current is listed on the datasheet. 11. Can I obtain a non-tri-state function for this product series? This product series only offers a tri-state option on pad one of the oscillators. The customer can use this oscillator series as a non-tri-state oscillator by setting the voltage on tri-state control (pad one) to either no connect or logic high. The oscillator has an internal pull up resistor on tri-state control (pad one). The datasheet provides the VIH and VIL thresholds for control of the tri-state function. 12. How do I specify the overall frequency stability for this product series? Ecliptek defines the frequency stability performance of the device inclusive of specific oscillator operating conditions. This is often called the "Inclusive Method". Ecliptek specifies the following parameters for this series of product: Calibration Frequency Tolerance at 25°C Frequency Stability over Operating Temperature Range Supply Voltage Output Load EC26 TEN10-005-002 Rev C Page 3 of 7 Ecliptek Frequently Asked Questions First Year Aging at 25°C 260°C Reflow Shock and Vibration 13. What is oscillator aging and what are the aging specifications for this product series? Aging is the systematic change in frequency with time due to internal changes in the crystal and/or oscillator. Aging is often expressed as a maximum value in parts per million per year [ppm/year]. The rate of aging is logarithmic in nature. The following factors effect oscillator aging: adsorption and desorption of contamination on the surfaces of the quartz, stress relief of the mounting and bonding structures, material outgassing, and seal integrity. The oscillator aging specification is listed on the datasheet. 14. What are the rms phase jitter and phase noise characteristics for this product series? RMS Period Jitter is a time domain measurement and is specified in picoseconds (pSec) as a maximum value. Phase noise is a measure in the frequency domain and is specified in decibels at various offset points from the carrier (-dBc/Hz). Phase jitter, (often called offset jitter) is derived from the phase noise measurement of the spectral density over a given offset bandwidth. Ecliptek uses a proprietary design, exclusive processing methods and a unique ASIC output driver circuit enabling this product series to have exceptionally low phase jitter and phase noise. The rms phase jitter parameter can be found on the datasheet. 15. What is duty cycle and what is the duty cycle specification for this product series? Duty cycle is the measure of output waveform uniformity. This term, also referred to as symmetry, is a measurement of the time that the output waveform is in a logic high state, expressed as a percentage (%) of the clock period. This parameter is measured at a specified voltage threshold or at a percentage of the output waveform amplitude. See the datasheet for measurement thresholds and load conditions. 16. What are the output and output load characteristics for this product series? Ecliptek offers this product series with a low voltage high speed CMOS driver that enables the output signal to swing from ground to VDD. The oscillator output topology is designed so as to optimize circuit load matching and signal performance. Signal integrity is optimized when the low impedance output of the oscillator is driving a high impedance-low capacitance input. The output load specification is listed on the datasheet. 17. Is start-up time specified for this product series? As shown in the figure below, start-up time is defined as the time (t0) from when the power supply reaches its specified VIH value to the time (t1) the oscillator output signal amplitude reaches its steady state VOH output logic high level and the output is within the specified frequency tolerance. EC26 TEN10-005-002 Rev C Page 4 of 7 Ecliptek Frequently Asked Questions Figure: Oscillator Start-up Timing Diagram In order to ensure proper start-up, the power supply start-up should have an exponential curve typical of a capacitive charge of a linear voltage ramp. The maximum start-up time specification can be found on the datasheet. 18. How do I electrically test this product series at my facility? The recommended electrical test fixture can be found on the datasheet. 19. Is this product series compatible with my existing assembly process equipment? If the part number is specified with the TR packaging option, oscillator products are delivered to the customer in EIA481 compliant tape and reel packaging. Without the TR option, products are delivered to the customer in bulk packaging as specified on the datasheet. 20. Is this product series compatible with my existing reflow processes? This product series is capable of withstanding industry standard high temperature (260°C, 10 seconds) convection reflow processes and is rated MSL1 per J-STD-020. The suggested solder reflow diagram is provided on the datasheet. 21. Is this product series RoHS compliant and Pb-free? This product is RoHS compliant and Pb-free as defined in the Ecliptek RoHS Compliant (Pb-free) Roadmap. 22. How can I obtain a RoHS compliant (Pb-free) certification for this product series? A RoHS and Pb-free product certification letter can be obtained directly from our website by using the Ecliptek RoHS/Pb-Free Certification Letter Generator. 23. Is an IPC-1752 material declaration available for customer review? Ecliptek can provide a Material Declaration in compliance with IPC-1752 to assist customers with their material compliance requirements. EC26 TEN10-005-002 Rev C Page 5 of 7 Ecliptek Frequently Asked Questions 24. How do I layout my printed circuit board for this product series? A suggested solder pad layout is provided on the datasheet. The customer should layout their PCB to include proper connections for the tri-state control input function. 25. Who do I contact if I have additional technical questions about the use of this product series? The Global Customer Support team at Ecliptek can provide applications engineering support or answer customer technical questions. 26. How do I order an oscillator that has custom requirements not specified on the standard oscillator series specification sheet? Please contact the Ecliptek Global Customer Support team for additional support or questions regarding your oscillator requirements. 27. What are the environmental and mechanical specifications for this product series? The environmental and mechanical specifications for this product series are listed on the datasheet. 28. What reliability information is available for this product series? Failure in Time (FIT) and Mean Time to Failure (MTTF) reliability data is available for this product series within the product series qualification and reliability report found on the series home page. 29. Is thermal resistance information available for this product series? θJA and θJC values are available for this product series and can be found on the Environmental / Mechanical section of the series homepage. 30. Are IBIS models available for this product series? Input/Output Buffer Information Specification (IBIS) modeling information, if available, can be found on the series home page. 31. What is the marking scheme for this product series? This series of product has a pad one (1) locator dot and alpha numeric marking content on the top of the part. The marking includes an Ecliptek manufacturing identifier. This identifier is used internally at Ecliptek for manufacturing lot traceability. This identifier may change at any time and provides no indication of part number or date code or output frequency. The datasheet provides the marking. 32. Can I identify the Ecliptek part number or specification based upon the markings on top of the part? In order to protect our customer’s intellectual property, the Ecliptek part marking does not identify the Ecliptek part number or specifications. EC26 TEN10-005-002 Rev C Page 6 of 7 Ecliptek Frequently Asked Questions 33. Where can I get the information regarding discontinued or End of Life (EOL) products? Any Ecliptek part number currently under an End of Life statement will be identified as EOL on an Ecliptek quotation, along with a link to the EOL statement. This information can also be found on the End of Life Statements for Discontinued and Obsolete Products section of our website. 34. Is Ecliptek ISO 9000 Certified? Yes, Ecliptek is certified to ISO 9001. 35. How can I obtain a REACH compliance statement for this product series? A Registration, Evaluation, Authorization, and Restriction of Chemicals (REACH) compliance statement can be obtained directly from our website by using the Ecliptek REACH Compliance Resources page of our website. EC26 TEN10-005-002 Rev C Page 7 of 7