Digital J/K Type Thermometer

User's Guide
Digital J/K Type Thermometer
Model TM100
Introduction
Congratulations on your purchase of the Extech TM100 Digital Thermometer with single K/J-type
input. This device is shipped fully tested and calibrated and, with proper use, will provide years of
reliable service. Please visit our website (www.extech.com) to check for the latest version of this
User Guide, Product Updates, and Customer Support.
Safety
To prevent personal injury or meter damage, use the meter only as specified in this guide
WARNING
To avoid electrical shock or personal injury, do not apply more than
20Vrms between the thermocouple inputs or between the thermocouple
and earth ground
Description
Meter
1.
2.
3.
4.
5.
Thermocouple input connector
Function buttons (Power, Enter, C-F-K)
Function buttons (Hold, MAX/MIN, Set)
LCD display
Battery compartment
Display
1.
2.
3.
4.
5.
6.
7.
Setup
Offset option
Hold mode
Auto power off
Upper display T1 reading
Temperature units
Lower display (max, min,
avg, offset value of T1)
8. Max, Min and Average
9. Time display
10. K/J type thermocouple
11. Low Battery
2
TM100-EU-EN v1.3 12/13
Operation
Connecting thermocouples
1.
This meter accepts a K/J-type thermocouple with spade lugs (sub-miniature type with one
spade wider than the other).
2.
Plug the thermocouple into the meter's thermocouple input jack.
Measuring
1.
Press the
button to switch ON the thermometer on. After 1 second the thermometer will
display the first temperature reading (upper display).
2.
Press the C-F-K button to select the desired temperature unit of measure. A display icon will
reflect the selection.
3.
Touch the object to be measured with the probe. Read the measured temperature on the
display.
Note: If the display indicates “OL” the temperature is outside the measurement range. The
display shows "- - - -" when a thermocouple is not connected.
MAX/MIN/AVG mode
Press MAX/MIN to capture and step through the maximum (MAX), minimum (MIN) and average
(AVG) temperature values. These values will be shown in the lower display with an elapsed time
reference below (hrs:mins, mins:secs).
1.
Press MAX/MIN to enter this mode.
2.
Press MAX/MIN to step through maximum, minimum and average readings.
3.
Press and hold MAX/MIN for 3 seconds to return to normal mode.
Data Hold
Press the HOLD button to freeze the reading in the display. HOLD will appear at the top right of
the display. Press the HOLD button again to return to normal operation mode.
Backlight
Press the SETUP button to switch the backlight OFF/ON.
3
TM100-EU-EN v1.3 12/13
Setup option
The setup option is used to select the thermocouple type that matches the type that will be
connected to the meter, to switch the sleep mode OFF/ON, and to adjust the thermocouple offset.
Note: In the setup mode, the upper display shows the menu items and the lower display shows
the selection for a given menu item.
Press and hold the SET button for 3 seconds to enter or exit the Setup mode. When the
thermometer is in Setup mode, the display shows the SETUP display icon.
Set Type J or K thermocouple
1.
Press ▲ or ▼to scroll to the “TYPE” setting (shown on the bottom left of the display).
2.
Press ENTER to choose the option.
3.
Press ▼ to toggle between J and K.
4.
Press and hold the SET button for 3 seconds to save the setting and return to normal mode.
Set Sleep/Non-sleep mode
The thermometer enters sleep mode by default. The meter will automatically shut off after 20
minutes of inactivity (no buttons pressed). When the thermometer is in Setup mode, the display
shows the SETUP display icon.
1.
Press ▲ or ▼to scroll to the SLP setting.
2.
Press ENTER to choose the option; On or OFF will appear in the display.
3.
Use the arrow key ▼ to select ON or OFF.
4.
Press ENTER to store the new setting.
5.
Press and hold the SET button for 3 seconds to return to normal mode.
Set Offset
Use the offset option in Setup (T1 menu item) to adjust the thermometer’s readings to
compensate for known temperature offset at a specific temperature. The adjustment range is ±
5.0°C or ± 9.0 °F.
1.
Plug the thermocouple into the input connector.
2.
Place the thermocouple into the known, stable temperature environment (such as an ice
bath or dry well calibrator). Allow the reading to stabilize.
3.
Use the arrow keys ▲ ▼ to scroll to the “T1” option and then press ENTER.
4.
Change the offset temperature reading (upper display) by pressing ▼until the desired
temperature is reached.
5.
Press and hold the SET button for 3 seconds to return to normal mode.
4
TM100-EU-EN v1.3 12/13
Replacing the Batteries
1.
Switch OFF the thermometer.
2.
Loosen the battery compartment screw and remove the compartment door.
3.
Replace the AAA batteries.
4.
Replace the battery door and tighten the screw.
Never dispose of used batteries or rechargeable batteries in household waste.
As consumers, users are legally required to take used batteries to appropriate
collection sites, the retail store where the batteries were purchased, or wherever
batteries are sold.
Disposal: Do not dispose of this instrument in household waste. The user is obligated to take end-oflife devices to a designated collection point for the disposal of electrical and electronic equipment.
Other Battery Safety Reminders
o Never dispose of batteries in a fire. Batteries may explode or leak.
o Never mix battery types. Always install new batteries of the same type.
Specifications
Temperature Range:
K type thermocouples
-200°C to 1372°C (-328°F to 2501°F)
J type thermocouples
-210°C to 1100°C (-346°F to 2012°F)
Note that thermocouple wire may be insulated with materials that cannot withstand temperatures
in the ranges listed above. Check that the thermocouples used are rated for the temperature
measurements to be made.
Temperature accuracy:
T1 Above –100 °C (-148 °F)
T1 Below –100 °C (-148 °F)
± [0.15%rgd+1°C (1.8°F)]
± [0.5%rgd+2°C (3.6°F)]
Display Resolution:
0.1°C /°F /°K <1000, 1°C /°F /°K >1000
Power supply:
Three (3) AAA 1.5V batteries
Operating Temperature:
0°C to 50°C (40°F to 122°F)
Storage Temperature:
10°C to 50°C (14°F to 122°F)
Dimensions:
220 x 63 x 28mm (8.7 x 2.5 x 1.1”)
Weight:
200g (7oz)
Copyright © 2013 FLIR Systems, Inc. All rights reserved including the right of reproduction in whole or in part in any form www.extech.com 5
TM100-EU-EN v1.3 12/13