User Guide AC/DC Mini Clamp Meter Model 380941 P Introduction Congratulations on your purchase of Extech’s AC/DC Clamp Meter. This professional meter, with proper care, will provide years of safe reliable service. Front Panel Description 6. One-touch DCA zero key 7. LCD Display 8. 40 segment bargraph display 1. Current sense jaw 2. Measurement Trigger 3. Function switch 4. Data Hold key 5. Max Min key 1 9. Positive input terminal for V, HZ and 10. COM termin 2 5 6 7 8 9 P 3 4 10 International Symbols ! Caution ! Refer to the explanation in this Manual Caution ! Risk of electric shock Earth (Ground) Safety This meter has been designed to be safe in use, but the operator must use caution in its operation. The rules listed below should be carefully followed for safe operation. 1. NEVER apply voltage or current to the meter that exceeds the specified maximum: 2. USE EXTREME CAUTION when working with high voltages. 3. DO NOT measure voltage if the voltage on the "COM" input jack exceeds 500V above earth ground. 4. NEVER connect the meter leads across a voltage source while the function switch is in the current, resistance or diode mode; doing so can damage the meter. 5. ALWAYS discharge filter capacitors in power supplies and disconnect the power when making resistance or diode tests. 6. ALWAYS turn off the power and disconnect the test leads before opening the back to replace the fuse or batteries. 7. NEVER operate the meter unless the back cover and the battery/fuse door are in place and fastened securely. 2 380941A-en-GB_V1.2 12/14 Operation AC Current Measurements WARNING: To avoid electric shock, disconnect the test leads from the meter before making current measurements. 1) 2) 3) Set the Function switch to the 40 or 200A AC range. Press the jaw trigger and clamp around, fully enclosing a single conductor. Do not allow a gap between the two halves of the jaw. Read the ACA value on the LCD. DC Current Measurements WARNING: To avoid electric shock, disconnect the test leads from the meter before making current measurements. 1) 2) 3) 4) 5) Set the Function switch to the 40 or 200A DC range. Press the DCA zero key to null the meter display. Press the Trigger to open the current sense Jaw. Fully enclose the conductor to be measured. Do not allow a gap between the two halves of the jaw. Read the DCA value on the LCD. AC Voltage Measurements WARNING: To avoid electric shock or damage to the meter, do not make any voltage measurements that exceed the maximum specified. 1) 2) 3) 4) Set the Function switch to the VAC position. Insert the test leads to the meter as follows: Red lead to “V,Hz,” terminal; Black lead to the COM input. With the pointed end of the test leads measure voltage. Remember that voltage measurements are made in parallel with the device or circuit under test. Read the ACV value on the LCD. DC Voltage Measurements WARNING: To avoid electric shock or damage to the meter, do not make any voltage measurements that exceed the maximum specified. 1) 2) 3) 4) Set the Function switch to the VDC position. Insert the test leads to the meter as follows: Red lead to “V,Hz,” terminal; Black lead to the COM input. With the pointed end of the test leads measure voltage. Remember that voltage measurements are made in parallel with the device or circuit under test. Read the DCV value on the LCD. 3 380941A-en-GB_V1.2 12/14 Resistance and Continuity Measurements WARNING: To avoid electric shock or damage to the meter, remove power to the circuit under test and discharge all capacitors. 1) 2) 3) 4) 5) Set the Function switch to the position. Insert the test leads to the meter as follows: Red lead to “V,Hz,” terminal; Black lead to the COM input. With the pointed end of the test leads measure resistance. Remember that resistance measurements are made in parallel with the device or circuit under test. Read the resistance value on the LCD. If the resistance is less than 40, the continuity beeper will sound. Frequency Measurements 1) 2) 3) 4) 5) Ensure that at least 0.1A AC is detectable with an ACA measurement before measuring Frequency. Set the Function switch to the Hz position. Insert the test leads to the meter as follows: Red lead to “V,Hz,” terminal; Black lead to the COM input. With the pointed end of the test leads measure frequency Read the Frequency measurement on the LCD in Hz. Additional Features Relative Measurements 1) 2) 3) 4) 5) 6) 7) Press the Zero key and the present measurement will Zero. All subsequent measurements are displayed with respect to the zeroed reading. For example, if a 20A reading is zeroed and a 30A reading is subsequently measured, the LCD will display 10A. To return to normal operation, press the zero key one more time. Note that Relative mode is not available if the MIN/MAX mode is enabled. Relative mode is not available in continuity or Hz mode. Note that the Zero button is disabled if ohm and continuity or Hz functions are selected. LCD displays relative numerical value without bargraph. Data Hold To freeze a reading on the LCD, press the Data Hold key. The HOLD icon will appear and the measurement will be held on the meter’s LCD. To release the Data Hold function and return the meter to normal operation, press the Data Hold key again. Data Hold is disabled if ohm and continuity function are selected. MIN/MAX Reading Mode Pressing the MIN/MAX key allows the meter to display ONLY the highest and the lowest readings encountered. Press the MIN/MAX key once to view the minimum reading, press it again to view the maximum reading. The LCD will toggle between the MIN and MAX values. Press and hold MIN/MAX button for more than 2 seconds to return to normal operating mode. Zero function will be disabled when MIN/MAX is enabled. MIN/MAX is not available in continuity or Hz mode. 4 380941A-en-GB_V1.2 12/14 Specifications General Specifications Display 3-3/4 (4032 count) Digit LCD with 40 segment bargraph Functions ACA, DCA, ACV, DCV, Resistance, Frequency, Continuity Polarity “-“ indicates negative polarity Current sensor Hall effect sensor type Overload indication OL DCA zero adjust One touch zero key Display rate 3 readings/second (30 readings/second for bargraph) Battery Two 1.5V AA batteries Operating temperature -10 C to 50 C (4 F to 122 F) Operating humidity < 85% RH Power consumption Approximately 17mA DC Sampling time 3 times/sec (display); 30 times/sec (bargraph) o o o o Weight 225g (8 oz.) including battery Dimensions 183 x 63.6 x 35.6mm (7.2 x 2.5 x 1.4”) (HWD) Jaw opening 23mm (0.9”) Standards IEC 1010 Category III 300V, Category II 600V Range Specifications Function DC Current Range Resolution. Overload protect 40A 10mA ±(1.0% +2dgts) 400A DC 0 to 150A 100mA ±(1.0% +2dgts) 400A DC 150 to 200A 100mA ±(2.2% +2dgts) 400A DC AC Current DC Voltage Accuracy 50/60Hz 40 to 400Hz 40A 10mA ±(1.0% +3dgts) ±(1.5% +4dgts) 400A AC 0 to 150A 100mA ±(1.0% +3dgts) ±(1.5% +4dgts) 400A AC 150 to 200A 100mA ±(2.2% +3dgts) ±(2.5% ±4dgts) 400A AC 400V 0.1V ±(1.0% +2dgts) AC Voltage 50/60Hz 40 to 400Hz 1000VDC 400V 0.1V ±(1.5% +2dgts) ±(2.0% +4dgts) 800V AC Resistance 40 to 400 0.1 ±(1.0% +2dgts) Beeper <approx 38 600V AC Frequency 1 to 100k 0.001-100 ±0.5% ±2dgts Sensitivity; 600V AC 10VAC 5 380941A-en-GB_V1.2 12/14 Maintenance Battery Replacement 1) 2) 3) 4) When the low battery symbol appears on the LCD the batteries must be replaced. Turn the meter off and remove the rear battery compartment screw. Remove the battery compartment cover and replace the two 1.5V AA cells. Replace the compartment cover and secure the screw. You, as the end user, are legally bound (Battery ordinance) to return all used batteries and accumulators; disposal in the household garbage is prohibited! You can hand over your used batteries / accumulators at collection points in your community or wherever batteries / accumulators are sold! Disposal: Follow the valid legal stipulations in respect of the disposal of the device at the end of its lifecycle Cleaning Caution: Use only a dry cloth to clean the plastic case. Copyright © 2014 FLIR Systems, Inc. All rights reserved including the right of reproduction in whole or in part in any form www.extech.com 6 380941A-en-GB_V1.2 12/14