Power line chokes Ring core chokes with iron powder core 1 … 6 A, 0.7 … 20 mH, +40 °C Series/Type: B82615 Date: July 2012 a~í~=pÜÉÉí © EPCOS AG 2015. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. EPCOS AG is a TDK Group Company. Power line chokes B82615 Ring core chokes with iron powder core Rated voltage 250 V AC / 350 V DC Rated current 1 ... 6 A Rated inductance 0.7 ... 20 mH Construction ■ ■ ■ ■ ■ Ring core single choke Iron powder core with epoxy coating Polycarbonate case (UL 94 V-0) Polyurethane potting (UL 94 V-0) Multilayer winding Features ■ High suppression of differential-mode ■ ■ ■ ■ interferences at low frequencies High thermal stability due to complete potting Suitable for wave soldering Design complies with EN 60938-2 (VDE 0565-2) RoHS-compatible Applications ■ ■ ■ ■ Suppression of differential-mode interferences Filter circuits in switch-mode applications Power factor correction (PFC) Reduction of harmonics in consumer goods Terminals ■ ■ ■ ■ ■ Base material CuNi18Zn20 Layer composition Ni, Sn Hot-dipped Pins 1.0 1.0 (mm) Lead spacing 15 40 (mm) Marking Manufacturer, ordering code, rated current, rated inductance, rated voltage, date of manufacture (YYWWD.internal ID code) Delivery mode Blister tray in cardboard box Please read Cautions and warnings and Important notes at the end of this document. 2 07/12 Power line chokes B82615 Ring core chokes with iron powder core Dimensional drawing and pin configuration 2 4 3 1.0 15±0.2 1 4+1 30 _ 0.5 42.4 max. 3.5 _ 0.4 1 2 4 3 Tolerances to ISO 2768-C unless otherwise noted. Dimensions in mm. 40±0.2 44 max. IND0232-V Technical data and measuring conditions Rated voltage VR 250 V AC (50/60 Hz) / 350 V DC Rated temperature TR +40 C Rated current IR Referred to 50 Hz and rated temperature Rated inductance LR Defined at zero DC current bias Measured with Agilent 4284A at 0.1 mA, +20 C Measuring frequency: LR 1 mH = 100 kHz LR > 1 mH = 10 kHz Inductance tolerance 20% at +20 C Inductance at rated current Measured at DC magnetic bias with IR with Agilent 4284A at 0.1 mA, +20 C, typical values Measuring frequency: LR 1 mH = 100 kHz LR > 1 mH = 10 kHz DC resistance Rtyp Measured at +20 C, typical values Solderability (lead-free) Sn96.5Ag3.0Cu0.5: +(245 5) °C, (3 0.3) s Wetting of soldering area 95% (to IEC 60068-2-20, test Ta) Resistance to soldering heat (wave soldering) +(260 5) °C, (10 1) s (to IEC 60068-2-20, test Tb) Climatic category 40/125/56 (to IEC 60068-1) Storage conditions (packaged) –25 °C … +40 °C, 75% RH Weight Approx. 115 g Please read Cautions and warnings and Important notes at the end of this document. 3 07/12 Power line chokes B82615 Ring core chokes with iron powder core Characteristics and ordering codes LR L at IR, typ. Rtyp A mH mH 1 20 11 IR Ordering code 3.0 B82615B2102M001 2 5.0 2.3 0.90 B82615B2202M001 3 2.5 1.3 0.40 B82615B2302M001 4 1.5 0.76 0.22 B82615B2402M001 5 1.0 0.41 0.15 B82615B2502M001 6 0.7 0.28 0.10 B82615B2602M001 Please read Cautions and warnings and Important notes at the end of this document. 4 07/12 Power line chokes B82615 Ring core chokes with iron powder core Impedance |Z| versus frequency f measured at +20 °C, typical values Relative inductance Lop/LR versus relative current Iop/IR measured at +20 °C, typical values IND0869-B 10 6 B82615 Ω IND0870-D 110 L op % B82615 LR |Z | 10 5 90 10 4 80 70 10 3 60 B2102M001 B2202M001 B2302M001 B2402M001 B2502M001 B2602M001 10 2 10 1 4 10 10 5 10 6 B2102M001 B2202M001 B2302M001 B2402M001 B2502M001 B2602M001 50 40 30 Hz 10 7 f 20 0 Current derating Iop/IR versus ambient temperature TA 5 07/12 0.2 0.4 0.6 0.8 1 I op IR 1.4 Cautions and warnings Current-compensated ring core double chokes ■ Please note the recommendations in our Inductors data book (latest edition) and in the data sheets. – Particular attention should be paid to the derating curves given there. Derating must be applied in case the ambient temperature in the application exceeds the rated temperature of the component. – Ensure the operation temperature (which is the sum of the ambient temperature and the temperature rise caused by losses / self-heating) of the component in the application does not exceed the maximum value specified in the climatic category. – The soldering conditions should also be observed. Temperatures quoted in relation to wave soldering refer to the pin, not the housing. ■ If the components are to be washed varnished it is necessary to check whether the washing varnish agent that is used has a negative effect on the wire insulation, any plastics that are used, or on glued joints. In particular, it is possible for washing varnish agent residues to have a negative effect in the long-term on wire insulation. Washing processes may damage the product due to the possible static or cyclic mechanical loads (e.g. ultrasonic cleaning). They may cause cracks to develop on the product and its parts, which might lead to reduced reliability or lifetime. ■ The following points must be observed if the components are potted in customer applications: – Many potting materials shrink as they harden. They therefore exert a pressure on the plastic housing or core. This pressure can have a deleterious effect on electrical properties, and in extreme cases can damage the core or plastic housing mechanically. – It is necessary to check whether the potting material used attacks or destroys the wire insulation, plastics or glue. – The effect of the potting material can change the high-frequency behaviour of the components. ■ Ferrites are sensitive to direct impact. This can cause the core material to flake, or lead to breakage of the core. ■ Even for customer-specific products, conclusive validation of the component in the circuit can only be carried out by the customer. Please read Cautions and warnings and Important notes at the end of this document. 6 07/12 Important notes Current-compensated ring core double chokes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. The aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products. 6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms of Delivery for Products and Services in the Electrical Industry” published by the German Electrical and Electronics Industry Association (ZVEI). 7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CeraLink, CSMP, CSSP, CTVS, DeltaCap, DigiSiMic, DSSP, FilterCap, FormFit, MiniBlue, MiniCell, MKD, MKK, MLSC, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.epcos.com/trademarks. 7 07/12