Bussmann® Power Distribution Blocks 163 Series up to 420 Amps, 600 Volts ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ 163 Series Power Distribution Blocks (Replaces Bussmann 164 Series) Ratings: up to 420A, 600V Construction: Thermoset plastic with UL rating 160¡C; ASTM rating to 260¡C. UL 94 VO. Tin-plated aluminum connectors; contact factory for copper connector options. Agency Information: UL Recognized: UL E221592 General Industrial Class per UL1059 CSA Certified: CSA File 53787, Class 6228-01 Termination Options: See page 2. 1-pole 1.96" 2-pole 3.58" Available in 1, 2 or 3 pole versions Smaller package...requires 40% less panel space than the 164 series. Touch-safe design. Extended barriers and optional cover to guard against accidental contact when live. Thermoset material to withstand high heat applications. Wide range of input/output terminations (see page 2 for details). Optional cover is clear with write-on surface for field termination identification (Order part number CPDB series). For industrial controls, HVAC and other control automation panel applications. Mounting slots allow greater flexibility to fit predrilled panel holes. Optional Covers: #4 Thread-cutting screws assembled 12345678 4.14" Textured surface for marking 12345678 CPDB-1 (single pole) 2.10" CPDB-2 (two pole) 3.72" CPDB-3 (three pole) 5.34" (Covers ordered and shipped separately.) 3-pole 5.20" .31" 3.37" 4.00" .97" 1.62" 3.25" 3.32" Mtg. hole .21X.41, c'bore .42X.62X.12 deep 6-25-03 J02104 Form No. 163 Series Page 1 of 2 Data Sheet: 1148 Bussmann® Power Distribution Blocks 163 Series up to 420 Amps, 600 Volts Cross Reference/ Replacement Guide INPUT/OUTPUT TERMINATION OPTIONS Basic Part No. Wire Size Line Side Load Side 16301 250kcmil-#6 CU Only 250kcmil-#6 CU Only 255 16303 350kcmil-#6 CU-AL 350kcmil-#6 CU-AL 310 16306 500kcmil-#6 CU-AL 500kcmil-#6 CU-AL 380 16321 2/0-#14CU, 2/0-#8AL #4-#14CU, #4-#8AL 175 16323 350kcmil-#6CU-AL #4-#14CU, #4-#12AL 310 16325 2/0-#14CU, 2/0-#8AL #4-#14CU, #4-#8AL 350 16330 500kcmil-#6CU-AL #2-#14CU, #2-#12AL 380 16332 350kcmil-#6CU-AL (3) #2-#14CU, #2-#8AL (2) 1/0-#14CU, 1/0-#8AL 310 (3) #2-#14CU, #2-#8AL (2) 1/0-#14CU, 1/0-#8AL 380 16335 500kcmil-#6CU-AL Amps/ Pole LINE / LOAD 16370 350kcmil-#6CU-AL #4-#14CU, #4-#12AL 310 16371 350kcmil-#6CU-AL (6) #2-#14CU, #2-#8AL (3) 1/0-#14CU, 1/0-#8AL 310 16372 350kcmil-#6CU-AL (21) #10-#14CU, #10AL 310 16373 350kcmil-#6CU-AL (14) #10-#14CU, #10AL (3) 1/0-#14CU-AL 310 16375 600kcmil-#2CU-AL #4-#14CU, #4-#12AL 420 16376 600kcmil-#2CU-AL (6) #2-#14CU, #2-#8AL (3) 1/0-#14CU, 1/0-#8AL 420 Stud Size (2) 1/4-20X1 380 Stud Size 3/8-16X1-1/8 Stud Size 3/8-16X1-1/8 250 Stud Size 1/2-13X1-1/16 Stud Size 1/2-13X1-1/16 400 Stud Size 3/8-16X1-7/16 Stud Size (2) 1/4-20X9/16 310 16378 16390 16394 16395 500kcmil-#6CU-AL NEW Buss Part No. 16303 16306 16321 16323 16370 16371 Replaces these part numbers. Old Connectron Marathon Gould ILSCO Buss No. Series Series Series 16302 16401, 16305 143 66 PDB 16320 144 67 16322 145 68 350CCC 69 16420, 16421 16423, 16535 350BBA 16375 16521 600CCC 16376 16425, 16431, 16520 600BBA 16378 16481 16382 16380, 16480 16390 16391 16394 16493, 16593 16395 16490 Note: Bussmann 164 Series was discontinued and replaced by the new Bussmann 163 Series in 1996. Contact Bussmann for a direct cross on a specific part number. Ordering Information: 163 Series blocks are available in 1, 2 or 3 poles. To order: Basic Part No. + Number of poles Examples: 16301-1 = (one-pole block) 16303-3 = (three-pole block) The only controlled copy of this Data Sheet is the electronic read-only version located on the Bussmann Network Drive. All other copies of this BIF document are by definition uncontrolled. This bulletin is intended to clearly present comprehensive product data and provide technical information that will help the end user with design applications. Bussmann reserves the right, without notice, to change design or construction of any products and to discontinue or limit distribution of any products. Bussmann also reserves the right to change or update, without notice, any technical information contained in this bulletin. Once a product has been selected, it should be tested by the user in all possible applications. 6-25-03 J02104 Form No. 163 Series Page 2 of 2 Data Sheet: 1148