AZ9371 SENSITIVE SUBMINIATURE RELAY FEATURES • • • • • • • • Extremely small footprint Thin vertical profile only 0.275" (7 mm) wide High sensitivity, 113 mW pickup Dielectric strength 4000 Vrms 5 Amp switching capability (version “T” 10 Amp) Two different footprints available UL, CUR file E44211 VDE 40030746 GENERAL DATA CONTACTS Arrangement SPST (1 Form A) Ratings Resistive load: Max. switched power: (Version “T”: Max. switched current: (Version “T”: Max. switched voltage: Life Expectancy Mechanical 150 W or 1385 VA 300 W or 2770 VA) 5A 10 A) 30 VDC* or 277 VAC * Note: If switching voltage is greater than 30 VDC, special precautions must be taken. Please contact the factory. Rated Load UL/CSA 5 A at 277/250/125 VAC General Use [1][2] 5 A at 30 VDC General Use [1][2] B300 Pilot Duty 120/240 VAC, 125/250VAC [2] "T" Version 10 A at 277/250/125 VAC General Use [1][2] 10 A at 30 VDC General Use [1][2] Minimum operations 5 million operations Standard version Electrical 1 X 105 at 5 A, 250 VAC res. [1] 5 X 104 at 5 A, 250 VAC res. [2] High capacity version “T” Electrical 1 X 105 at 7 A, 250 VAC res. [1] 1 X 104 at 10 A, 250 VAC res. [1][2] 3 X 104 at 7 A, 250 VAC res. [2] Operate Time (typical) 10 ms at nominal coil voltage Release Time (typical) 10 ms at nominal coil voltage (with no coil suppression) Dielectric Strength (at sea level for 1 min.) 4000 Vrms coil to contact 1000 Vrms between open contacts Insulation Resistance 1000 megohms min. at 20°C, 500 VDC, 50% RH Dropout Greater than 5% of nominal coil voltage Ambient Temperature Operating Storage At nominal coil voltage -40°C (-40°F) to 85°C (185°F) -40°C (-40°F) to 105°C (221°F) Vibration 0.062" (1.5 mm) DA at 10–55 Hz Shock 10 g Enclosure P.B.T. polyester Terminals Tinned copper alloy, P.C. Max. Solder Temp. 270°C (518°F) Max. Solder Time 5 seconds 1. All values at 20°C (68°F). Max. Solvent Temp. 80°C (176°F) 2. Relay may pull in with less than “Must Operate” value. Max. Immersion Time 30 seconds 3. Specifications subject to change without notice. Weight 3 grams VDE 5 A at 250 VAC / 30 VDC [1][2] 10 A at 250VAC / 30 VDC (T version) Material Silver nickel [1], silver tin oxide [2], gold plating available Resistance < 100 milliohms initially (at 6 V, 1 A, voltage drop method) COIL Power At Pickup Voltage (typical) 113 mW Max. Continuous Dissipation 750 mW at 20°C (68°F) ambient Temperature Rise 26°C (47°F) at nominal coil voltage Temperature Max. 105°C (221°F) NOTES 9/10/10 AZ9371 RELAY ORDERING DATA COIL SPECIFICATIONS Nominal Coil VDC Must Operate VDC Max. Continuous VDC Coil Resistance Ohm ± 10% 3 2.25 3.9 45 AZ9371-1A-3D 5 3.75 6.5 125 AZ9371-1A-5D 6 4.50 7.8 180 AZ9371-1A-6D 9 6.75 11.7 405 AZ9371-1A-9D 12 9.00 15.6 720 AZ9371-1A-12D 18 13.50 23.4 1620 AZ9371-1A-18D 24 18.00 31.2 2880 ORDER NUMBER AZ9371-1A-24D *Add "T" after "AZ9371" for high capacity version. Add “E" after "1A" to indicate silver tin oxide contacts. Add suffix "E" for sealed version. Add suffix “K” for K version footprint. Add suffix “G” at the end of order number for gold plated contacts. 9/10/10 AZ9371 MECHANICAL DATA Standard Pinning Outline Dimensions Version"K" Pinning Outline Dimensions 0.3 + 0.15 - 0.1 0.3 + 0.15 - 0.1 + 0.2 0.8 Ø 0.4 - 0.05 11.5 7.0 15 .3 ± 0.3 3.4 ± 0.3 0.3 3.4 ± 0.3 0.3 15 .3 ± 0.3 7.2 max 20.5 max 7.2 max 20.5 max 0.3 + 0.15 - 0.1 0.3 4.7 3.5 PC BOARD LAYOUT + 0.15 - 0.1 + 0.2 0.8 Ø 0.4 - 0.05 15 4.7 PC BOARD LAYOUT 7 4.7 4 x ø 1.1 4.7 4 x ø 1.1 3.5 11.5 15 Viewed toward terminals Viewed toward terminals WIRING DIAGRAM WIRING DIAGRAM 13 7 5 1 Viewed toward terminals 5 7 13 1 Viewed toward terminals Attention! Grid is not 0.1” (2.54 mm)!! 9/10/10