Type ESRE Solid Polymer Aluminum SMT Capacitors Capacitance Tripled Type ESRE polymer aluminum capacitors are low voltage polarized electrolytic capacitors, with extremely low equivalent series resistance at high frequency. This yields capacitors with very low high frequency impedance and higher ripple current capability than aluminum electrolytic or tantalum capacitors. One type ESRE capacitor can replace three or more tantalum or aluminum electrolytic capacitors. The solid electrolyte of the polymer aluminum capacitor gives it a long life that is ignition free. Highlights Type ESRE capacitors triple the capacitance found in CDE’s type ESRD capacitors. Applications • Lowest ESR: <10 mΩ at 100 kHZ • 3.5 A ripple current at 100 kHz • “D” case footprint: 7.3 (l) x 4.3 (w) • Ignition Free Motherboard By-Pass Switching Supply Input/Output Filters Power Supply Decoupling High Frequency Noise Reduction Laptop LCD Displays Automotive Digital Equipment Portable Electronic Equipment Markings Polarity Stripe (Anode) + W.V. Code Capacitance (“R” = Decimal Point) D = 2.0V E = 2.5V G = 4.0V Lot Code J = 6.3V K = 8.0V Ordering Information ESRE 101 M 08 R Packaging Code CDE Type WVDC Code Capacitance Code Capacitance Tolerance 02 =2.0 Vdc 06 = 6.3 Vdc 101 = 100 µF M = ±20% 0E =2.5 Vdc 08 = 8.0 Vdc R = Tape & Reel 2000 pcs/reel 04 =4.0 Vdc CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde. com Type ESRE Solid Polymer Aluminum SMT Capacitors Surface Mount, High Capacitance Outline Drawing Ratings Capacitance (µF) Maximum Catalog E.S.R. Part Number 100 kHz/20 ºC (Ω) 2.0 Vdc Maximum Ripple Current 100 kHz/105 ºC (Amps) 270 ESRE271M02R 0.012 3.3 330 ESRE331M02R 0.012 3.3 390 ESRE391M02XR 0.010 3.5 2.5 Vdc 220 ESRE221M0ER 0.012 3.3 270 ESRE271M0ER 0.012 3.3 330 ESRE331M0EXR 0.010 3.5 4.0 Vdc 180 ESRE181M04R 0.012 3.3 220 ESRE221M04XR 0.010 3.5 6.3 Vdc 150 ESRE151M06R 0.012 3.3 180 ESRE181M06XR 0.010 3.5 0.012 3.3 8.0 Vdc 100 ESRE101M08R CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde. com Type ESRE Solid Polymer Aluminum SMT Capacitors Specifications Operating Temperature Range: –55 °C to +105 °C, at 100% rated voltage Surge Voltage: 125% of the rated working Vdc Capacitance Range: 100 µF to 390 µF Capacitance Tolerance: ±20% at 120 Hz and +20 °C DC Leakage Current (DCL): After a two minute application of the rated working voltage at +20 °C: 2V — 4V: I ≤0.06CV 6.3V — 8V: I ≤0.04CV or 3 µA (whichever greater) Dissipation Factor (DF): The ratio of the capacitor’s equivalent series resistance to its reactance at 120Hz and +20 ºC ESRE: DF is 0.10 Max. Resistance to Soldering Heat: Heat the capacitors at 235 ºC in an oven for 200 seconds. The capacitors will meet the following limits after stabilizing at 20 ºC: ∆C = ±10% of the initial measured value DF ≤ the initial specified value DCL ≤ the initial specified value Vibration: No abnormal change shall occur to capacitors that have been soldered (and attached) to a board when subjected to a vibration of 1.5 mm amplitude that is varied from 10 Hz to 2000 Hz in 20 min. cycles. The test duration is 2 hours for each right angle direction (total 6 hours). Capacitance is monitored during the last cycle of the test for stablilty. Moisture Resistance: After 500 hours storage at +60 ºC and 90% to 95% RH without load, the capacitor will meet the following limits: ∆C = +70%/–20% of the initial measured value (2.0 Vdc, 2.5 Vdc), +60%/–20% of the initial measured value (4.0 Vdc), +50%/–20% of the initial measured value (6.3 Vdc), +40%/–20% of the initial measured value (all other voltages) DF ≤ two times the initial specified value DCL ≤ the initial specified value Life Test: Apply rated DC working voltage at 105 ºC for 1000 hours, and then stabilize them to +20 ºC. Capacitors will meet the following limits: ∆C = ±10% of the initial measured value DF ≤ the initial specified value DCL ≤ the initial specified value Shelf Life Test: Shelf life is typically 5 to 10 years. Accelerated test: after 500 hours at 105 ºC, capacitors will meet the following limits after stabilization at 20 ºC: ∆C = ±10% of the initial measured value DF ≤ the initial specified value DCL ≤ the initial specified value Shear Test: No damage shall be visible after subjecting a mounted capacitor to a side force of 5 N for 10 seconds. For more information on this product please see the Solid Polymer Aluminum Capacitors Application Guide CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde. com Type ESRE Solid Polymer Aluminum SMT Capacitors Notice and Disclaimer: All product drawings, descriptions, specifications, statements, information and data (collectively, the “Information”) in this datasheet or other publication are subject to change. The customer is responsible for checking, confirming and verifying the extent to which the Information contained in this datasheet or other publication is applicable to an order at the time the order is placed. All Information given herein is believed to be accurate and reliable, but it is presented without any guarantee, warranty, representation or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based on the knowledge that the Cornell Dubilier company providing such statements (“Cornell Dubilier”) has of operating conditions that such Cornell Dubilier company regards as typical for such applications, but are not intended to constitute any guarantee, warranty or representation regarding any such matter – and Cornell Dubilier specifically and expressly disclaims any guarantee, warranty or representation concerning the suitability for a specific customer application, use, storage, transportation, or operating environment. The Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by Cornell Dubilier with reference to the use of any Cornell Dubilier products is given gratis (unless otherwise specified by Cornell Dubilier), and Cornell Dubilier assumes no obligation or liability for the advice given or results obtained. Although Cornell Dubilier strives to apply the most stringent quality and safety standards regarding the design and manufacturing of its products, in light of the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies or other appropriate protective measures) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product-related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicated in such warnings, cautions and notes, or that other safety measures may not be required. CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde. com