US07A THRU US07M M US07A THRU US07 US07M 1.0 AMP. SURFACE MOUNT GENERAL PURPOSE ULTRA FAST RECTIFIERS SOD-123FL FEATURES ·Glass passivated device ·Ideal for surface mouted applications ·Low reverse leakage ·Metallurgically bonded construction ·Superfast recovery time for high efficiency ·High temperature soldering guaranteed: 250℃/10 seconds at terminals. MECHANICAL DATA ·Case: JEDEC SOD-123FL,molded plastic over passivated chip ·Terminals:Solder Plated, solderable per MIL-STD-750, Method 2026 ·Polarity: Color band denotes cathode end ·Weight: 0.006 ounces, 0.02 gram ·Mounting position: Any Dimensions in millimeters MAXIMUM RATINGS AND ELECTRONICAL CHARACTERISTICS Ratings at 25℃ ambient temperature unless otherwise specified. Single phase, half wave, 60Hz,resistive or inductive load. For capacitive load, derate current by 20%. SYM B US07 D US07 G US07A US07 S07B S07D S07G US07 S07JJ BOL Type Number UA UB UD UG UJ marking Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward rectified Current at TA =65°C (Note 1) VRRM VRMS VDC K US07 S07K M US07 S07M UK UM units 50 100 200 400 600 800 1000 V 35 70 140 280 420 560 700 V 50 100 200 400 600 800 1000 V IF(AV) 1.0 A IFSM 25 A Peak Forward Surge Current 8.3ms single half sine-wave superimposed on rate load (JEDEC method) Maximum Instantaneous forward Voltage at 0.7A DC Maximum DC Reverse Current @TA =25°C at rated DC blocking voltage @TA =125°C Maximum Reverse Recovery Time (Note 2) Typical Junction Capacitance (Note 3) Typical thermal resistance (Note 4) Storage Temperature Range Operation Temperature Range VF 1.0 1.3 1.7 5.0 IR µA 100.0 trr CJ R(JA) TSTG TJ 50 75 nS 20 15 pF Note: 1. Averaged over any 20 ms period. 2.Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A 3. Measured at 1MHz and applied reverse voltage of 4.0 volts d.c. 4. Measured on P.C.Board with 0.2×0.2”(5.0×5.0mm)Copper Pad Areas 1 V 180 °C /W -55 to +150 °C -55 to +150 °C US07A THRU US07M RATING AND CHARACTERISTIC CURVES (US07A THRU US07M S07M)) FIG.1-TYPICAL FORWARD CURRENT DERATING CURVE FIG.2-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 0.5 Single Phase Half Wave 60Hz Resistive or inductive Load 0 0 50 150 100 1.0 40 0V 0V 00 1 0V 60 TJ=25℃ Pulse Width=300μs 1% Duty Cycle .1 .01 200 50 V20 0V 1.0 INSTANEOUS FORWARD CURRENT,(A) AVERGE FORWARD RECTIFIED CURRENT,(A) 10 1.0 .6 1.4 2.2 1.8 AMBIENT TEMPERTURE,(℃) INSTANEOUS FORWARD VOLTAGE,(V) FIG.3-MAXIMUN NON-REPETITIVE FORWARD SURGE CURRENT FIG.4-TYPICAL REVERSE CHARACTERISTICS 40 INSTANEOUS REVERSE CURRENT,(μA) PEAK FORWARD SURGE CURRENT,(A) 10 8.3ms Single Half Sine-Wave (JEDEC Method) 30 20 10 1.0 TJ=25℃ .1 .01 0 0 100 10 0 20 40 60 FIG.5-TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERSITIC (+) 25Vdc (approx) (-) 100 120 PERCENT OF RATED PEAK REVERSE VOLTAGE,(%) NUMBER OF CYCLES AT 60Hz 50 Ω NONINDUCTIVE 80 trr 10 Ω NONINDUCTIVE +0.5A 0 (+) PULSE GENERATOR -0.25A (NOTE 2) 1Ω (NOTE 1) NON- OSCILOSCOPE INDUCTIVE (-) -1.0A NOTES: NOTES:1. Rise Time=7ns max, Input Impedance= 1 megohm.22pF. 2. Rise Time=10ns max, Souce Impedance= 50 ohms. 2 140 US07A THRU US07M 3