MNR02 Resistors Chip resistor networks MNR02 (1005 × 2 size) zFeatures 1) Extremely small and light Area ratio is 60% smaller than that of chip 1616 (MNR12), while weight ratio has been cut 75%. 2) High-density mounting Can be mounted even more densely than two 1005 chips (MCR01). Also, the cost of mounting has been reduced. 3) Compatible with a wide range of mounting equipment. Squared corners make it excellent for mounting using image recognition devices. 4) Convex electrodes Easy to check the fillet after soldering is finished. 5) ROHM resistors have obtained ISO-9001 certification. Design and specifications are subject to change without notice. Carefully check the specification sheet before using or ordering it. zRatings Item Rated power Conditions Specifications Power must be derated according to the power derating curve in Figure 1 when ambient temperature exceeds 70°C. 0.063W (1 / 16W) at 70°C 100 POWER LOAD (%) 80 60 40 20 0 −55 0 70 100 125 155 AMBIENT TEMPERATURE (°C) Fig.1 Rated voltage The voltage rating is calculated by the following equation. If the value obtained exceeds the limiting element voltage, the voltage rating is equal to the maximum operating voltage. E: Rated voltage (V) E= P×R P: Rated power (W) R: Nominal resistance (Ω) Nominal resistance Operating temperature Limiting element voltage 25V See Table 1. −55°C to +125°C Rev.A 1/5 MNR02 Resistors Table 1 Resistance tolerance J (±5%) Resistance range (Ω) 10≤R≤1M Resistance temperature coefficient (ppm / °C) ±300 (E24) •Before using components in circuits where they will be exposed to transients such as pulse loads (short-duration, high-level loads), be certain to evaluate the component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that is greater than its rated voltage. zCharacteristics Items Resistance Variation of resistance with temperature Overload Solderability Resistance to soldering heat Rapid change of temperature Guaranteed value Resistor type J : ±5% See Table.1 ± (2.0%+0.1Ω) A new uniform coating of minimum of 95% of the surface being immersed and no soldering damage. ± (1.0%+0.05Ω) No remarkable abnormality on the appearance. JIS C 5201-1 4.5 JIS C 5201-1 4.8 Measurement : −55 / +25 / +125°C JIS C 5201-1 4.13 Rated voltage (current) ×2.5, 2s. Limiting Element Voltage×2 : 50V JIS C 5201-1 4.17 Rosin·Ethanol (25%WT) Soldering condition : 235±5°C Duration of immersion : 2.0±0.5s. JIS C 5201-1 4.18 Soldering condition : 260±5°C Duration of immersion : 10±1s. ± (1.0%+0.05Ω) JIS C 5201-1 4.19 Test temp. : −55°C to +125°C 5cyc ± (3.0%+0.1Ω) JIS C 5201-1 4.24 40°C, 93%RH Test time : 1,000h to 1,048h ± (3.0%+0.1Ω) JIS C 5201-1 4.25.1 Rated voltage (current), 70°C 1.5h : ON − 0.5h : OFF Test time : 1,000h to 1,048h ± (3.0%+0.1Ω) JIS C 5201-1 4.25.3 125°C Test time : 1,000h to 1,048h ± (1.0%+0.05Ω) JIS C 5201-1 4.29 23±5°C, Immersion cleaning, 5±0.5min. Solvent : 2-propanol Damp heat, steady state Endurance at 70°C Endurance Resistance to solvent Bend strength of the end face plating Test conditions (JIS C 5201-1) ± (1.0%+0.05Ω) Without mechanical damage such as breaks. JIS C 5201-1 4.33 Rev.A 2/5 MNR02 Resistors zExternal dimensions (Unit: mm) 1.0±0.1 0.25±0.1 0.2±0.1 1.0±0.1 A Cross section A-A' 1 6 5 2 B' 0.35±0.1 +0.05 0.34 −0.1 Material No. 5 Cross section B-B' A' +0.1 0.33 −0.05 1 6 B 3 4 1 Thick dielectric glaze of oxide metal 2 Thick film of silver for electrode 3 Nickel-coated electrode 4 Sn electrode 5 Alumina substrate 6 Overcoating 0.68 zEquivalent circuit R1 R2 R1 = R2 Rev.A 3/5 MNR02 Resistors zPackaging Reel Taping P0 0 φD P2 E F W 02 04 06 08 06 D 04 B 02 A 08 B0 A0 P1 Heat crimp cover / Tape Thick paper (Underside paper tape) mount Chip network resistors Square punchout hole T2 C Label (Unit: mm) EIAJ ET-7200B compliant W F E A0 B0 8.0±0.3 3.5±0.05 1.75±0.1 1.17±0.1 1.17±0.1 D0 P0 P1 P2 T2 4.0±0.1 2.0±0.1 2.0±0.05 Max. 0.5 (Unit: mm) A φ180 B 0 −1.5 φ60 +1 0 C 9 +1.0 0 D φ13±0.2 φ1.5 +0.1 0 zProduct designation P Part No. Resistance tolerance Nominal resistance J ±5% J is also used for jumper. Resistance code, 3 digits, 000 denotes Jumper type. Packaging Specifications Code Part No. Code MNR02 M0AP Resistance tolerance J(±5%) Packaging specifications Reel Basic ordering unit (pcs) Paper tape (2mmPitch) φ180mm (7in). 10,000 Reel (φ180mm) : Compatible with JEITA standard "EIAJ ET-7200B" : Standard product Rev.A 4/5 MNR02 Resistors JIS C 5201-1 4.5 SAMPLE SIZE : n=40pcs 20°C 65%RH 5.0 3.0 2.0 1.0 0 −1.0 −2.0 −3.0 −4.0 −5.0 −6.0 10 100 1k 10k 100k 1M 300 2.0 100 0 −100 0 −2.0 −200 −4.0 −300 −400 10 100 1k 10k 100k −6.0 1M 10k 100k Fig.2 Resistance Fig.3 Variation resistance with temperature Fig.4 Overload JIS C 5201-1 4.19 SAMPLE SIZE : n=20pcs −55°C / 125°C 5cyc 2.0 2.0 ∆R/R (%) 0 0 −1.0 −1.0 −2.0 −2.0 −2.0 −4.0 1k 10k 100k 1M JIS C 5201-1 4.24 SAMPLE SIZE : n=20pcs 40°C 93%RH WITH NO LOAD 1,000h 4.0 1.0 100 1M 6.0 3.0 0 −6.0 −3.0 10 100 1k 10k 100k 1M 10 100 1k 10k 100k 1M RESISTANCE (Ω) RESISTANCE (Ω) RESISTANCE (Ω) Fig.5 Resistance to soldering heat Fig.6 Rapid change of temperature Fig.7 Damp heat, steady state 6.0 6.0 JIS C 5201-1 4.25.1 SAMPLE SIZE : n=20pcs 70°C 1,000h OVERLOAD : THE RATED VOLTAGE 4.0 JIS C 5201-1 4.25.3 SAMPLE SIZE : n=20pcs 125°C WITH NO LOAD 1,000h 4.0 2.0 ∆R/R (%) 2.0 ∆R/R (%) 1k RESISTANCE (Ω) 1.0 0 0 −2.0 −2.0 −4.0 −4.0 −6.0 100 RESISTANCE (Ω) JIS C 5201-1 4.18 SAMPLE SIZE : n=20pcs SOLDERING CONDITION : 260°C 10s 10 10 RESISTANCE (Ω) 2.0 −3.0 JIS C 5201-1 4.13 SAMPLE SIZE : n=20pcs RATED VOLTAGE×2.5TIMES 2s LIMITING ELEMENT VOLTAGE×2 : 100V 4.0 200 3.0 ∆R/R (%) JIS C 5201-1 4.8 SAMPLE SIZE : n=20pcs 25°C / −55°C 25°C / 125°C ∆R/R (%) DC RESISTANCE (%) 4.0 6.0 400 ∆R/R (%) 6.0 TEMPERATURE COEFFICIENT (ppm / °C) zElectrical characteristics 10 100 1k 10k 100k 1M −6.0 10 100 1k 10k 100k RESISTANCE (Ω) RESISTANCE (Ω) Fig.8 Endurance at 70°C Fig.9 Endurance 1M Rev.A 5/5 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.1