For more information, please visit the product page. date 08/22/2013 page 1 of 3 MODEL: PJ-033B │ DESCRIPTION: DC POWER JACK FEATURES • • • • 2.5 mm center pin snap-in tabs through hole mount, vertical orientation 2 conductors, 1 internal switch RoHS SPECIFICATIONS parameter conditions/description min rated input voltage typ rated input current contact resistance1 between terminal and mating plug between terminal in a closed circuit insulation resistance at 500 Vdc voltage withstand at 50/60Hz for 1 minute any direction for 10 seconds -25 life A 50 30 mΩ mΩ 500 Vac 3 kg 500 g 85 °C 5,000 flammability rating UL94V-0 RoHS 2011/65/EU Note: 2.5 MΩ 0.3 operating temperature units Vdc 100 insertion/withdrawal force terminal strength max 16 cycles 1. When measured at a current of less than 100 mA / 1 kHz SOLDERABILITY parameter conditions/description wave soldering cui.com min typ max units 255 260 265 °C For more information, please visit the product page. CUI Inc │ MODEL: PJ-033B │ DESCRIPTION: DC POWER JACK date 08/22/2013│ page 2 of 3 MECHANICAL DRAWING units: mm[inches] tolerance: X.X ±0.2mm X.XX ±0.1mm X.XXX ±0.05mm MATERIAL PLATING center pin copper nickel terminal 1 brass tin terminal 2 copper alloy tin terminal 3 brass tin plastic PBT insulator resin laminate or PBT 15.5 0.610 12.0 0.472 6.0 0.236 0.3 (3 PLCS) 14.0 0.551 2.50 0.098 1.45 0.057 (2 PLCS) 2 13.0 0.512 5.00 0.197 (2 PLCS) 11.0 0.433 1 12.2 0.480 3 5.50 0.217 2.00 0.079 (3 PLCS) 0.80 0.031 7.00 0.276 6.10 0.240 11.20 0.441 6.60 0.260 3.2 0.126 3.2 0.126 3.60 0.142 0.90 0.035 2 1 2.4 0.094 3.9 0.154 3 8.20 0.323 11.00 0.433 2.10 0.083 1.20X3.00 (3 PLCS) PCB LAYOUT TOP VIEW 5.20 0.205 PANEL CUT OUT BACK VIEW 1 3 2 SCHEMATIC MATING PLUG Jack Insertion Depth: 8.2 mm Note: Model PJ-033B Center Pin ø2.5 mm 1. All specifications measured at 10~35°C, humidity at 45~85%, under standard atmospheric pressure, unless otherwise noted. cui.com 8.0 0.315 For more information, please visit the product page. CUI Inc │ MODEL: PJ-033B │ DESCRIPTION: DC POWER JACK date 08/22/2013│ page 3 of 3 REVISION HISTORY rev. description date 1.0 initial release 07/30/2007 1.01 changed insulator material to PBT, applied new spec template 08/22/2013 The revision history provided is for informational purposes only and is believed to be accurate. Headquarters 20050 SW 112th Ave. Tualatin, OR 97062 800.275.4899 Fax 503.612.2383 cui.com [email protected] CUI offers a one (1) year limited warranty. Complete warranty information is listed on our website. CUI reserves the right to make changes to the product at any time without notice. Information provided by CUI is believed to be accurate and reliable. However, no responsibility is assumed by CUI for its use, nor for any infringements of patents or other rights of third parties which may result from its use. CUI products are not authorized or warranted for use as critical components in equipment that requires an extremely high level of reliability. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.