For more information, please visit the product page. date 06/28/2011 page 1 of 3 SERIES: SJ-3502-SMT │ DESCRIPTION: MID MOUNT POWER JACK FEATURES •mid mount for low profile applications •shielded •no internal switches RoHS SPECIFICATIONS parameter conditions/description min rated input voltage typ rated input current contact resistance between after life between after life insulation resistance at 500 Vdc at 500 Vdc, after environmental tests voltage withstand at 50/60Hz for 1 minute insertion/withdrawl force terminal strength terminal and mating plug test, between terminal and mating plug terminal in a closed circuit1 test, between terminal in a closed circuit1 after life test units Vdc 1 A 50 100 30 60 mΩ mΩ mΩ mΩ 100 50 MΩ MΩ 0.3 0.2 any direction for 10 seconds operating temperature Notes: max 12 -25 500 Vac 3 2 kg kg 500 g 85 °C 1. When measured at a current of less than 100 mA / 1 kHz TESTING parameter conditions/description min typ max units solderability 95% solder coverage on lead, neutral flux, 2 sec. 250 255 260 °C reflow soldering see graph life at 24 insertion/withdrawl cycles per minute heat the relative test before and after testing should comply with the Insulation Resistance section 83 cold the relative test before and after testing should comply with the Insulation Resistance section 33 humidity the relative test before and after testing should comply with the Insulation Resistance section 38 Notes: 5,000 85 87 50 °C %RH hours 35 96 37 °C hours 40 96 42 °C hours %RH 96 90 cycles 95 All measurements and test shall be made at a temperature 10°C to 35°C with a relative humidity of 45% RH to 85% RH under the standard atmospheric pressure unless otherwise specified. cui.com For more information, please visit the product page. CUI Inc │ SERIES: SJ-3502-SMT │ DESCRIPTION: MID MOUNT POWER JACK date 06/28/2011 │ page 2 of 3 REFLOW SOLDERING 270 260 250 240 217 180 120 120 60 50 °C 70 60 140 120 250 180 340 240 300 380 360 430 420 480 Time (second) MECHANICAL DRAWING units: mm[inches] 9.9 0.390 MATERIAL PLATING terminal 1 stainless steel silver terminal 2 copper alloy silver terminal 3 copper alloy silver plastic PA6T 0.3 3.600 0.142 7.1 0.280 4.50 0.177 6.2 0.244 A 0.50 0.020 (6 PLCS) COPLANARITY 0.1 4.15 0.163 - 2.00 0.079 MODEL NO. 0.95 0.037 (4 PLCS) +0.2 -0.1 SJ-3502-SMT 1 3 SCHEMATIC 2.95 0.116 5.90 0.232 2 8.45 0.333 + DETAIL A SCALE 12 : 1 0.3 12.7 0.500 2.00 0.079 3.20X1.30 (4 PLCS) 5.6 0.220 12.5 0.492 2.40X0.50 (4 PLCS) 1 4.20 0.165 2 1 3.40 0.134 6.10 0.240 9.0 0.354 (2 PLCS) 5.6 0.220 (2 PLCS) 1 2 1 3.40 0.134 4.20 0.165 2.2 0.087 (2 PLCS) 1 2.2 0.087 (2 PLCS) TOLERANCE: X.X ±0.2mm X.XX ±0.1mm X.XXX ±0.05mm 3 9.0 0.354 (2 PLCS) 1 2.50X2.10 (2 PLCS) PCB LAYOUT TOP VIEW C, 0.55 1 3 0.45 0.018 (4 PLCS) 1 2.00 0.079 (6 PLCS) cui.com For more information, please visit the product page. CUI Inc │ SERIES: SJ-3502-SMT │ DESCRIPTION: MID MOUNT POWER JACK date 06/28/2011 │ page 3 of 3 REVISION HISTORY rev. 1.0 description date initial release 06/28/2011 The revision history provided is for informational purposes only and is believed to be accurate. Headquarters 20050 SW 112th Ave. Tualatin, OR 97062 800.275.4899 Fax 503.612.2383 cui.com [email protected] CUI offers a one (1) year limited warranty. Complete warranty information is listed on our website. CUI reserves the right to make changes to the product at any time without notice. Information provided by CUI is believed to be accurate and reliable. However, no responsibility is assumed by CUI for its use, nor for any infringements of patents or other rights of third parties which may result from its use. CUI products are not authorized or warranted for use as critical components in equipment that requires an extremely high level of reliability. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.