CLD-DS05 Rev 16D Product family data sheet Cree® XLamp® XR-E LED Product Description FEATURES Table of Contents The XLamp® XR-E LED is leading the LED • Available in white (2600 K to Characteristics.............................................2 lighting revolution with its unprecedented lighting-class brightness, efficacy, lifetime and quality of light. These lighting-class features enable the XLamp XR-E LED to replace many traditional light sources and save money with energyefficient light and long lifetimes. Cree XLamp LEDs bring 10,000 K CCT), blue, royal blue and Flux Characteristics - White.........................3 green Flux Characteristics - Color.........................4 • Maximum drive current: up to 1000 mA • Maximum junction temperature: 150 °C • Industry-leading JEDEC standard high performance and quality of light to a wide Relative Spectral Power Distribution..........5 Relative Flux vs. Junction Temperature......6 Electrical Characteristics.............................7 Relative Flux vs. Current..............................7 Typical Spatial Distribution..........................8 pre‑qualification testing Thermal design............................................8 • Reflow solderable – JEDEC Reflow Soldering Characteristics................9 J-STD-020C compatible Notes......................................................... 10 range of lighting applications, including • Electrically neutral thermal path Mechanical Dimensions........................... 12 color-changing lighting, portable and • RoHS- and REACh-compliant Tape and Reel............................................ 13 personal lighting, outdoor lighting, indoor • UL recognized component Packaging.................................................. 14 directional lighting, commercial lighting ® (E349212) www.cree.com/Xlamp and emergency-vehicle lighting. Copyright © 2006-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 1 XLamp ® XR-E LED Characteristics Characteristics Thermal Resistance, junction to solder point Unit Minimum Typical °C/W 8 Viewing Angle (FWHM) - white degrees 90 Viewing Angle (FWHM) - royal blue, blue, green degrees 100 mV/°C -4.0 Temperature Coefficient of Voltage - white, royal blue, blue, green ESD Classification (HBM per Mil-Std-883D) Maximum Class 2 DC Forward Current - white ≥ 5000 K, royal blue, blue mA 1000 DC Forward Current - white < 5000 K, green mA 700 DC Pulse Current (@ 1 kHz, 10% duty cycle) A 1.8 Reverse Voltage V 5 Forward Voltage (@ 350 mA) V 3.3 Forward Voltage (@ 700 mA) V 3.5 Forward Voltage (@ 1000 mA) - white ≥ 5000 K, royal blue, blue V 3.7 LED Junction Temperature °C 3.9 150 Copyright © 2006-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 2 XLamp ® XR-E LED Flux Characteristics - White (TJ = 25 °C) The following tables describe the available colors and flux for XR-E LEDs by listing the correlated color temperature or dominant wavelength range for the entire family and by providing several base order codes. It is important to note that the base order codes listed here are a subset of the total available order codes for the product family. For more order codes, as well as a complete description of the order-code nomenclature, please consult the XR Family Binning and Labeling document. Color Cool White Neutral White Warm White CCT Range Minimum 5000 K 3700 K 2600 K Maximum 10,000 K 5000 K 3700 K Minimum Luminous Flux Order Code Group Flux (lm) P4 80.6 XREWHT-L1-0000-00901 Q2 87.4 XREWHT-L1-0000-00A01 Q3 93.9 XREWHT-L1-0000-00B01 Q4 100 XREWHT-L1-0000-00C01 Q5 107 XREWHT-L1-0000-00D01 R2 114 XREWHT-L1-0000-00E01 P3 73.9 XREWHT-L1-0000-008E4 P4 80.6 XREWHT-L1-0000-009E4 Q2 87.4 XREWHT-L1-0000-00AE4 Q3 93.9 XREWHT-L1-0000-00BE4 Q4 100 XREWHT-L1-0000-00CE4 N3 56.8 XREWHT-L1-0000-005E7 N4 62.0 XREWHT-L1-0000-006E7 P2 67.2 XREWHT-L1-0000-007E7 P3 73.9 XREWHT-L1-0000-008E7 P4 80.6 XREWHT-L1-0000-009E7 Notes: • Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and ±2 on CRI measurements. See the Measurements section (page 10). • Typical CRI for Cool White & Neutral White (3700 K – 10,000 K CCT) is 75. • Typical CRI for Warm White (2600 K – 3700 K CCT) is 80. Copyright © 2006-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 3 XLamp ® XR-E LED Flux Characteristics - Color (TJ = 25 °C) The following tables describe the available colors and flux for XR-E LEDs by listing the correlated color temperature or dominant wavelength range for the entire family and by providing several base order codes. It is important to note that the base order codes listed here are a subset of the total available order codes for the product family. For more order codes, as well as a complete description of the order-code nomenclature, please consult the XR Family Binning and Labeling document. Dominant Wavelength Range Minimum Color DWL (nm) Group Royal Blue D3 450 Maximum Group DWL (nm) D5 465 Dominant Wavelength Range Minimum Color Maximum Group DWL (nm) Group DWL (nm) B3 465 B6 485 Blue Dominant Wavelength Range Minimum Color Group DWL (nm) G2 520 Green Maximum Minimum Radiant Flux (mW) Order Code Group Flux (mW) 13 300 XREROY-L1-0000-00801 14 350 XREROY-L1-0000-00901 15 425 XREROY-L1-0000-00A01 Minimum Luminous Flux (lm) Order Code Group Flux (lm) J 23.5 XREBLU-L1-0000-00J01 K 30.6 XREBLU-L1-0000-00K01 Minimum Luminous Flux (lm) Group DWL (nm) Group Flux (lm) G4 535 P 67.2 Order Code XREGRN-L1-0000-00P01 Note: Cree maintains a tolerance of ±7% on flux and power measurements and ±1 nm on dominant wavelength measurements. See the Measurements section (page 10). Copyright © 2006-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 4 XLamp ® XR-E LED Relative Spectral Power Relative Spectral Power Distribution Relative Radiant Power (%) 100 80 5000 K - 10000 K CCT 60 3700 K - 5000 K CCT 40 2600 K - 3700 K CCT 20 0 380 430 480 530 580 630 680 730 780 Wavelength (nm) Relative Radiant Power (%) 100 80 60 Royal Blue Blue 40 Green 20 0 380 430 480 530 580 630 680 730 780 Wavelength (nm) Copyright © 2006-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 5 XLamp ® XR-E LED Relative Flux Output vs. Junction Temperature Relative Flux vs. Junction Temperature (IF = 350 mA) 100% 90% Relative Luminous Flux 80% 70% 60% White 50% Blue 40% Green 30% 20% 10% 0% 25 50 75 100 125 150 Junction Temperature (°C) 100% 90% Relative Radiant Flux 80% 70% 60% Royal Blue 50% 40% 30% Electrical Characteristics (Tj = 25ºC) 20% 10% 0% 25 50 75 100 125 150 Junction Temperature (ºC) Copyright © 2006-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 6 XLamp ® XR-E LED Electrical Characteristics (TJ = 25 ˚C) 1000 Forward Current (mA) 900 800 700 600 500 400 Thermal Design 300 200 100 0 0.0 1.0 2.0 3.0 4.0 5.0 Forward Voltage (V) Relative Flux vs. Current (TJ = 25 ˚C) Relative Luminous Flux (%) 250 200 150 Green 100 White, Royal Blue & Blue Typical Spatial Radiation Pattern 50 0 0 200 400 600 800 1000 Forward Current (mA) Copyright © 2006-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 7 XLamp ® XR-E LED Typical Spatial Distribution Relative Luminous Intensity (%) 100 80 60 White 40 Royal Blue, Blue & Green 20 -90 -70 -50 -30 0 -10 10 30 50 70 90 Angle (°) Thermal design Thermal Design Cool White, Royal Blue & Blue Neutral White, Warm White & Green 800 1200 700 Maximum Current (mA) Maximum Current (mA) 1000 800 600 400 400 300 200 Rj-a = 15°C/W 200 500 Rj-a = 10°C/W Neutral White, Warm White, Blue, Royal Blue and Green Rj-a = 10°C/W Cool White 600 Rj-a = 15°C/W Rj-a = 25°C/W vs. Current (Tj = 25ºC) Relative Intensity 100 Rj-a = 20°C/W Rj-a = 35°C/W Rj-a = 25°C/W 0 0 20 40 60 80 100 120 Ambient Temperature (°C) White ≥ 5,000 K, Royal Blue, Blue 140 160 0 0 20 40 60 80 100 120 140 160 Ambient Temperature (°C) White < 5,000 K, Green Copyright © 2006-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 8 XLamp ® XR-E LED Reflow Soldering Characteristics In testing, Cree has found XLamp XR-E LEDs to be compatible with JEDEC J-STD-020C, using the parameters listed below. As a general guideline, Cree recommends that users follow the recommended soldering profile provided by the manufacturer of the solder paste used. Note that this general guideline may not apply to all PCB designs and configurations of reflow soldering equipment. tP TP Critical Zone TL to TP Temperature Ramp-up TL tS Tsmax Tsmin Ramp-down ts Preheat 25 t 25˚C to Peak IPC/JEDEC J-STD-020C Time Profile Feature Average Ramp-Up Rate (Tsmax to Tp) Lead-Free Solder 1.2 °C/second Preheat: Temperature Min (Tsmin) 120 °C Preheat: Temperature Max (Tsmax) 170 °C Preheat: Time (tsmin to tsmax) Time Maintained Above: Temperature (TL) Time Maintained Above: Time (tL) Peak/Classification Temperature (Tp) 65-150 seconds 217 °C 45-90 seconds 235 - 245 °C Time Within 5 °C of Actual Peak Temperature (tp) 20-40 seconds Ramp-Down Rate 1 - 6 °C/second Time 25 °C to Peak Temperature 4 minutes max. Note: All temperatures refer to topside of the package, measured on the package body surface. Copyright © 2006-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 9 XLamp ® XR-E LED Notes Measurements The luminous flux, radiant power, chromaticity and CRI measurements in this document are binning specifications only and solely represent product measurements as of the date of shipment. These measurements will change over time based on a number of factors that are not within Cree’s control and are not intended or provided as operational specifications for the products. Calculated values are provided for informational purposes only and are not intended as specifications. Pre‑Release Qualification Testing Please read the LED Reliability Overview for details of the qualification process Cree applies to ensure long-term reliability for XLamp LEDs and details of Cree’s pre-release qualification testing for XLamp LEDs. Lumen Maintenance Cree now uses standardized IES LM-80-08 and TM-21-11 methods for collecting long-term data and extrapolating LED lumen maintenance. For information on the specific LM-80 data sets available for this LED, refer to the public LM-80 results document. Please read the Long-Term Lumen Maintenance application note for more details on Cree’s lumen maintenance testing and forecasting. Please read the Thermal Management application note for details on how thermal design, ambient temperature, and drive current affect the LED junction temperature. Moisture Sensitivity Cree recommends keeping XLamp XR-E LEDs in the provided, resealable moisture-barrier packaging (MBP) until immediately prior to soldering. Unopened MBPs that contain XLamp LEDs do not need special storage for moisture sensitivity. Once the MBP is opened, XLamp XR-E LEDs should be handled and stored as MSL 4 per JEDEC J-STD-033, meaning they have limited exposure time before damage to the LED may occur during the soldering operation. The table on the right specifies the maximum exposure time in days depending on temperature and humidity conditions. LEDs with Temp. Maximum Percent Relative Humidity 30% 40% 50% 60% 70% 80% 90% 30 ºC 9 5 4 3 1 1 1 25 ºC 12 7 5 4 2 1 1 20 ºC 17 9 7 6 2 2 1 exposure time longer than the specified maximums must be baked according to the baking conditions listed below. Baking Conditions It is not necessary to bake all XLamp LEDs. Only the LEDs that meet all of the following criteria must be baked: 1. LEDs that have been removed from the original MBP. 2. LEDs that have been exposed to a humid environment longer than listed in the Moisture Sensitivity section above. 3. LEDs that have not been soldered. LEDs should be baked at 80 ºC for 24 hours. LEDs may be baked on the original reels. Remove LEDs from the MBP before baking. Do not bake parts at temperatures higher than 80 ºC. This baking operation resets the exposure time as defined in the Moisture Sensitivity section above. Copyright © 2006-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 10 XLamp ® XR-E LED Notes - Continued Storage Conditions XLamp LEDs that have been removed from the original MBP but not soldered yet should be stored in a room or cabinet that will maintain an atmosphere of 25 ± 5 ºC and no greater than 10% RH (relative humidity). For LEDs stored in these conditions, storage time does not add to exposure time as defined in the Moisture Sensitivity section above. RoHS Compliance The levels of RoHS restricted materials in this product are below the maximum concentration values (also referred to as the threshold limits) permitted for such substances, or are used in an exempted application, in accordance with EU Directive 2011/65/EC (RoHS2), as implemented January 2, 2013. RoHS Declarations for this product can be obtained from your Cree representative or from the Product Documentation sections of www.cree.com. REACh Compliance REACh substances of very high concern (SVHCs) information is available for this product. Since the European Chemical Agency (ECHA) has published notice of their intent to frequently revise the SVHC listing for the foreseeable future, please contact a Cree representative to insure you get the most up-to-date REACh SVHC Declaration. REACh banned substance information (REACh Article 67) is also available upon request. UL® Recognized Component Level 4 enclosure consideration. The LED package or a portion thereof has been investigated as a fire and electrical enclosure per ANSI/ UL 8750. Vision Advisory WARNING: Do not look at an exposed lamp in operation. Eye injury can result. For more information about LEDs and eye safety, please refer to the LED Eye Safety application note. Copyright © 2006-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 11 XLamp ® XR-E LED Mechanical Dimensions (TA = 25 °C) All measurements are ±.1 mm unless otherwise indicated. Lens Substrate Reflector Reflector Anode Lens Substrate 6.8 mm 4.4 ± .2 mm Side View 9.0 mm 8.4 mm 5.6 mm 0.7 mm 6.46 mm 7.0 mm Anode Bottom View Top View 8.4 mm 7.0 mm 8.4 mm 8.30 5.6 mm 0.70 mm 7.0 mm 7.10 6.46 mm 5.50 0.70 mm 6.36 5.6 mm 6.46 mm Recommended solder pad PC for Board XLampSolder XR family Recommended Pad LEDs 0.60 0.80 0.80 0.60 RECOMMENDED STENCIL PATTERN 7090 Recommended stencil pattern for XLamp XR family LEDs (HATCHED AREA IS OPENING) Recommended PC (hatched Board Solder Pad area is opening) Copyright © 2006-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 12 XLamp ® XR-E LED Tape and Reel 1.5 ± .1 4.0±.1 All Cree carrier tapes1.75±.10 conform to EIA-481D, Automated Component Handling Systems Standard. 12.0±.1 CATHODE SIDE All dimensions in mm. 16.0 +.3 -.0 1.5 ± .1 4.0±.1 13.5 (MIN) 1.75±.10 12.0±.1 +.3 SIDE ANODE 16.0 -.0 CATHODE SIDE 5.5±.1 13.5 (MIN) ANODE SIDE 5.5±.1 START USER FEED DIRECTION LOADED POCKETS 50 EMPTY POCKETS WITH TAPE LOADED POCKETS 60 (MIN) EMPTY POCKETS WITH TAPE USER FEED DIRECTION 5-10 EMPTY POCKTES WITH UNSEALED COVER TAPE 60 (MIN) EMPTY POCKETS WITH TAPE START 50 EMPTY POCKETS WITH TAPE 5-10 EMPTY POCKTES WITH UNSEALED COVER TAPE + 330.2 mm Copyright © 2006-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 13 XLamp ® XR-E LED Humidity Indicator Card (inside bag) Packaging Dessicant (inside bag) Unpackaged Reel Label with Cree Bin Code, Quantity, Reel ID Packaged Reel Dessicant (inside bag) Label with Cree Bin Code, Qty, Lot # Vacuum-Sealed Moisture Barrier Bag Label with Cree Order Code, Quantity, Reel ID, PO # Humidity Indicator Card (inside bag) Label with Cree Bin Code, Quantity, Reel ID Label with Custo Code, Qty, Reel I Boxed Reel Label with Cree Order Code, Quantity, Reel ID, PO # Patent Label Label with Cree Bin Code, Quantity, Reel ID Patent Label Copyright © 2006-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 14