KEMET Ceramic Surface Mount Capacitors High Voltage (≥ 500Vdc), ArcShield, X7R, Product Family Qualification per Q-200 Rev. D Results Summary Test Performed Method Reference Test Conditions C1812V334MCRAC C2220W334MBRAC C1206V333MBRAC C1210V683MDRAC KEMET Part # C0603W392KCRAC C0805V123MBRAC 0118T011806 0123T012310 1059T105903FT 4300100T07FT 0118T011801 0110T01006 Lot ID# Sample Size Failure Sample Size Failure Sample Size Failure Sample Size Failure Sample Size Failure Sample Size Failure (per lot) Count (per lot) Count (per lot) Count (per lot) Count (per lot) Count (per lot) Count Reliability and Environmental Tests High Temperature Life MIL-STD-202, Method 108 Condition D, Steady State TA = 125°C, 1.2X Rated. Measurement at 24 hrs. +/- 2 hrs after test conclusion. 77 0 77 0 77 0 77 0 77 0 77 0 Storage Life MIL-STD-202, Method 108 Unpowered, 1000 hours @ T=150°C. Measurement at 24 hrs. +/- 2hrs after test conclusion. 77 0 77 0 77 0 77 0 77 0 77 0 MIL-STD-202, Method 103 Load Humidity: 1000 hours 85°C/85%RH and 200 Vdc Maximum. Add 100K ohm resistor. Measurement at 24 hrs. +/- 2 hrs after test conclusion. 77 0 77 0 77 0 77 0 77 0 77 0 Low Volt Humidity MIL-STD-202, Method 103 Low Volt Humidity: 1000 hours 85C°/85%RH and 1.5V. Add 100K ohm resistor. Measurement at 24 hrs. +/- 2 hrs after test conclusion. 77 0 77 0 77 0 77 0 77 0 77 0 Temperature Cycle JESD22, Method JA-104 1000 Cycles (-55°C to +125°C), Measurement at 24 hrs. +/- 2 hrs after test conclusion. 77 0 77 0 77 0 77 0 77 0 77 0 0 All 0 All 0 All 0 All 0 All 0 Load Humidity Physical, Mechanical, and Process Tests External Visual Physical Dimensions Destructive Physical Analysis (DPA) Board Flex Terminal Strength Beam Load Test Resistance to Solvents Solderability Resistance to Soldering Heat ESD Mechanical Shock and Vibration MIL-STD-883, Method 2009 JESD22 Method JB-100 EAI-469 JIS-C-6429 JIS-C-6429 AEC-Q200-003 MIL-STD-202, Method 215 ANSI /J-STD-002 MIL-STD-202, Method 210 AEC-Q200-002 MIL-STD-202, Methods 213, 204 Inspect device construction, marking and workmanship. Electrical Test not required All Verify physical dimensions to the applicable device specification. Note: KEMET product catalog. Electrical test not required. 30 0 30 0 30 0 30 0 30 0 30 0 Electrical Test not required. Appendix 2, Note: 3mm (min). Appendix 1, Note: Force of 1.8kg for 60 seconds. - Ceramic SMD Only 10 30 30 30 0 0 0 0 10 30 30 30 0 0 0 0 10 30 30 30 0 0 0 0 10 30 30 30 0 0 0 0 10 30 30 30 0 0 0 0 10 30 30 30 0 0 0 0 Add Aqueous wash chemical - OKEM Clean or equivalent. 5 0 5 0 5 0 5 0 5 0 5 0 Magnification 50X. Conditions: a) Method B, 4 hrs @ 155°C, dry heat @ 235°C b) Method B @ 215°C category 3 c) Method D, category 3 @ 260°C Do not use banned solvents. 15 0 15 0 15 0 15 0 15 0 15 0 30 0 30 0 30 0 30 0 30 0 30 0 15 0 15 0 15 0 15 0 15 0 15 0 Test Condition D. Pre-heat condition of 150°C, 60-120sec is allowed for ceramic components 30 0 30 0 30 0 30 0 30 0 30 0 Electrical Test not required. Magnification 50 X. Conditions:Human body model with 150 pF charge cap. One positive pulse, followed by discharge through 1 Mohm resistor, and then repeat cycle with negative pulse. Then perform electrical Figure 1 of Method 213, Condition F, Method 204: 12 cycles of 5 g for 20 minutes. 15 0 15 0 15 0 15 0 15 0 15 0 30 0 30 0 30 0 30 0 30 0 30 0 30 0 30 0 30 0 30 0 30 0 30 0 685 0 685 0 685 0 Electrical Characterization Temperature Coefficient Characterization (TCC) KEMET Custom Test Parametrically test per lot and sample size requirements, summary to show Min, Max, Mean and Standard deviation at room as well as Min and Max operating temperatures. Qualification Status APPROVED 685 0 685 0 685 BUSINESS CONFIDENTIAL NO PORTION OF THIS REPORT MAY BE DISCLOSED TO ANY THIRD PARTY WITHOUT WRITTEN CONSENT OF KEMET ELECTRONICS CORPORATION 0 KEMET Ceramic Surface Mount Capacitors High Voltage (≥ 500Vdc), Arcshield, Flexible Termination, X7R, 3900pF, 500 Vdc, 0603 Case Size Qualification per Q-200 Rev. D and Results Summary - Lot Id. 4300100T07FT Initial Readings High Temperature Life 125°C, 1.2x Rated Voltage, Hours 1000 Storage Life 125°C, 0 Volts, 1000 Hours Load Humidity 85°C, 85% RH, 200 Vdc max., 1000 Hours Low Volt Humidity 85°C, 85% RH, 1.5 Volts, 1000 Hours Temperature Cycle -55°C to +125°C, 1000 Cycles Post Test Readings Capacitance, pF DF, 1kHz, % IR, 25°C, MOhm Delta Cap, % DF, 1kHz, % IR, 25°C, MOhm Limits AVG STD 3510 - 4290 4207.69 61.06 2.50 1.41 0.02 10000.00 3194000.00 1.04 ± 20 -12.999 0.633 3.00 1.45 0.03 1000.00 5262000.00 1.17 Max 4289.39 1.46 3674000.00 -12.054 1.51 7387000.00 Min 4070.75 1.34 2959000.00 -14.457 1.39 4249000.00 Limits 3510 - 4290 2.50 10000.00 ± 20 3.00 1000.00 AVG STD Max Min Limits AVG STD Max Min Limits AVG STD Max Min Limits AVG STD Max Min 4177.97 73.53 4282.81 3988.63 3510 - 4290 4169.27 72.66 4288.08 5015.0684 3510 - 4290 4158.37 70.09 4283.03 4003.36 3510 - 4290 4166.26 65.65 4285.83 4010.59 1.28 0.07 1.63 1.20 2.50 1.25 0.06 1.45 1.20 2.50 1.23 0.05 1.36 1.17 2.50 1.21 0.05 1.41 1.15 3312000.00 1.06 3680000.00 2706000.00 10000.00 3319000.00 1.05 3713000.00 2944000.00 10000.00 3309000.00 1.05 3675000.00 2911000.00 10000.00 3291000.00 1.06 3643000.00 2808000.00 -14.670 0.812 -13.035 -16.625 ± 20 -6.224 0.570 -4.723 -7.281 ± 20 -0.593 0.319 0.241 -1.283 n/a -3.489 1.770 -2.042 -13.929 1.29 0.06 1.45 1.23 3.00 1.42 0.10 1.65 1.31 3.00 1.22 0.03 1.39 1.18 2.50 1.13 0.14 1.96 1.05 2617000.00 1.98 5874000.00 230200.00 1000.00 3697000.00 1.33 4482000.00 418700.00 1000.00 5635000.00 2.12 15000000.00 1330000.00 10000.00 2757000.00 1.14 3151000.00 1205000.00 BUSINESS CONFIDENTIAL NO PORTION OF THIS REPORT MAY BE DISCLOSED TO ANY THIRD PARTY WITHOUT WRITTEN CONSENT OF KEMET ELECTRONICS CORPORATION KEMET Ceramic Surface Mount Capacitors High Voltage (≥ 500Vdc), Arcshield, Flexible Termination, X7R, 3900pF, 500 Vdc, 0603 Case Size Qualification per Q-200 Rev. D and Results Summary - Lot Id. 4300100T07FT Initial Readings Resistance to Soldering Heat Test Condition D. Pre-heat condition of 150°C, 60-120sec is allowed for ceramic components Mechanical Shock / Vibration Method 213: Figure 1, Condition F. Method 204: 12 cycles of 5 g for 20 minutes Limits AVG STD Max Min Limits AVG STD Max Min Capacitance, pF 3510 - 4290 4060.94 71.50 4177.97 3909.13 3510 - 4290 4213.53 50.78 4285.81 4131.69 DF, 1kHz, % 2.50 1.37 0.04 1.44 1.29 2.50 1.38 0.02 1.41 1.34 Post Test Readings IR, 25°C, MOhm 10000.00 3302000.00 1.08 3724000.00 2838000.00 10000.00 3921000.00 1.22 4945000.00 2426000.00 Delta Cap, % n/a 6.192 0.453 7.050 5.189 n/a -0.678 1.121 0.988 -4.179 DF, 1kHz, % 2.50 1.53 0.04 1.59 1.46 2.50 1.39 0.03 1.43 1.32 IR, 25°C, MOhm 10000.00 2432000.00 1.05 2682000.00 2141000.00 10000.00 2655000.00 1.07 3096000.00 2377000.00 Electrical Characterization Temperature Coefficient Characterization (TCC) KEMET Custom Test: Parametrically test, show statistics at room, min, and max operating temperatures. -55°C Delta Cap (%) Reference Capacitance @ 25°C, pF +125°C Delta Cap (%) IR, 125°C MOhm Limits ± 15 3510 - 4290 ± 15 1000.00 AVG STD Max Min -8.25 0.26 -8.51 -7.86 4127.00 0.09 4009.00 4239.00 -9.86 0.23 -10.13 -9.72 16166.00 0.53 16839.00 15628.00 Dimensions, mm Other Mechanical / Performance Results ESD, per AEC-Q200-002 Beam Load, per AEC-Q200-003, MPascal, MPa Class AVG STD Max Min 4 2251 304 2656 1768 Limits AVG STD Max Min Length Width Thickness 1.43 - 1.77 1.67 0.01 1.69 1.66 0.65 - 0.95 0.79 0.02 0.82 0.77 0.73 - 0.87 0.79 0.00 0.85 0.75 BUSINESS CONFIDENTIAL NO PORTION OF THIS REPORT MAY BE DISCLOSED TO ANY THIRD PARTY WITHOUT WRITTEN CONSENT OF KEMET ELECTRONICS CORPORATION KEMET Ceramic Surface Mount Capacitors High Voltage (≥ 500Vdc), ArcShield, X7R, 12nF, 630 Vdc, 0805 Case Size Qualification per Q-200 Rev. D and Results Summary - Lot Id. 0118T011801 Initial Readings High Temperature Life 125°C, 1.2x Rated Voltage, Hours 1000 Storage Life 125°C, 0 Volts, 1000 Hours Load Humidity 85°C, 85% RH, 200 Vdc max., 1000 Hours Low Volt Humidity 85°C, 85% RH, 1.5 Volts, 1000 Hours Temperature Cycle -55°C to +125°C, 1000 Cycles Post Test Readings Capacitance, nF DF, 1kHz, % IR, 25°C, MOhm Delta Cap, % DF, 1kHz, % IR, 25°C, MOhm Limits AVG STD 9.6 - 14.4 13.20 0.16 2.50 1.14 0.04 8333.00 169000.00 1.20 ± 20 -10.85 0.55 3.00 1.26 0.04 833.30 12000.00 1.12 Max 13.55 1.21 726000.00 -9.98 1.36 15400.00 Min 12.84 1.06 150000.00 -11.82 1.16 10300.00 Limits 9.6 - 14.4 2.50 8333.00 ± 20 3.00 833.30 AVG STD Max Min Limits AVG STD Max Min Limits AVG STD Max Min Limits AVG STD Max Min 13.08 0.17 13.47 12.62 9.6 - 14.4 13.06 0.21 13.66 12.5930 9.6 - 14.4 13.00 0.18 13.40 12.6000 9.6 - 14.4 13.14 0.14 13.56 12.77 1.05 0.02 1.10 1.02 2.50 1.04 0.02 1.13 1.02 2.50 1.00 0.03 1.08 0.95 2.50 1.06 0.02 1.13 1.04 171000.00 1.06 191000.00 134000.00 8333.00 171000.00 1.05 186000.00 157000.00 8333.00 164000.00 1.07 182000.00 117000.00 8333.00 168000.00 1.06 184000.00 134000.00 -13.17 0.57 -12.21 -14.47 ± 20 -5.45 0.53 -3.18 -6.152 ± 20 0.90 0.27 1.46 0.168 n/a -2.64 0.18 -2.21 -3.33 1.20 0.07 1.26 1.05 3.00 1.17 0.11 1.37 0.96 3.00 1.09 0.04 1.20 1.03 2.50 0.95 0.02 1.01 0.09 16800.00 1.97 31700.00 17000.00 833.30 13200.00 2.01 30600.00 10000.00 833.30 64100.00 2.44 15000.00 30800.00 8333.00 135000.00 1.09 211000.00 113000.00 BUSINESS CONFIDENTIAL NO PORTION OF THIS REPORT MAY BE DISCLOSED TO ANY THIRD PARTY WITHOUT WRITTEN CONSENT OF KEMET ELECTRONICS CORPORATION KEMET Ceramic Surface Mount Capacitors High Voltage (≥ 500Vdc), ArcShield, X7R, 12nF, 630 Vdc, 0805 Case Size Qualification per Q-200 Rev. D and Results Summary - Lot Id. 0118T011801 Initial Readings Resistance to Soldering Heat Test Condition D. Pre-heat condition of 150°C, 60-120sec is allowed for ceramic components Mechanical Shock / Vibration Method 213: Figure 1, Condition F. Method 204: 12 cycles of 5 g for 20 minutes Limits AVG STD Max Min Limits AVG STD Max Min Capacitance, nF 9.6 - 14.4 13.24 0.14 13.47 13.01 9.6 - 14.4 13.22 0.17 13.45 12.92 DF, 1kHz, % 2.50 1.25 0.03 1.30 1.13 2.50 1.25 0.03 1.31 1.18 Post Test Readings IR, 25°C, MOhm 8333.00 195000.00 1.04 212000.00 178000.00 8333.00 137000.00 1.06 148000.00 119000.00 Delta Cap, % n/a -3.61 1.48 -1.09 -5.80 n/a -4.96 0.79 -3.40 -6.26 DF, 1kHz, % 2.50 1.21 0.03 1.28 1.13 2.50 1.29 0.04 1.38 1.17 IR, 25°C, MOhm 8333.00 128000.00 1.16 185000.00 105000.00 8333.00 145000.00 1.07 158000.00 123000.00 Electrical Characterization Temperature Coefficient Characterization (TCC) KEMET Custom Test: Parametrically test, show statistics at room, min, and max operating temperatures. -55°C Delta Cap (%) Reference Capacitance @ 25°C, nF +125°C Delta Cap (%) IR, 125°C MOhm Limits ± 15 9.6 - 14.4 ± 15 833.30 AVG STD Max Min -8.91 0.40 -8.03 -9.76 12.90 0.16 13.15 12.52 -12.53 0.84 -11.38 -14.90 14500.80 1.25 20000.00 9810.00 Dimensions, mm Other Mechanical / Performance Results ESD, per AEC-Q200-002 Beam Load, per AEC-Q200-003, MPascal, MPa Class AVG STD Max Min 4 122 19 161 96 Limits AVG STD Max Min Length Width Thickness 1.8 - 2.4 2.13 0.02 2.16 2.09 1.05 - 1.45 1.33 0.01 1.35 1.30 1.10 - 1.40 1.18 0.02 1.20 1.13 BUSINESS CONFIDENTIAL NO PORTION OF THIS REPORT MAY BE DISCLOSED TO ANY THIRD PARTY WITHOUT WRITTEN CONSENT OF KEMET ELECTRONICS CORPORATION KEMET Ceramic Surface Mount Capacitors High Voltage (≥ 500Vdc), ArcShield, X7R, 33nF, 630 Vdc, 1206 Case Size Qualification per Q-200 Rev. D and Results Summary - Lot Id. 0110T01006 Initial Readings High Temperature Life 125°C, 1.2x Rated Voltage, Hours 1000 Storage Life 125°C, 0 Volts, 1000 Hours Load Humidity 85°C, 85% RH, 200 Vdc max., 1000 Hours Low Volt Humidity 85°C, 85% RH, 1.5 Volts, 1000 Hours Temperature Cycle -55°C to +125°C, 1000 Cycles Post Test Readings Capacitance, nF DF, 120 Hz, % IR, 25°C, MOhm Delta Cap, % DF, 120 Hz, % IR, 25°C, MOhm Limits AVG STD 26.4 - 39.6 36.76 0.02 2.50 1.09 0.03 3030.00 121000.00 1.18 ± 20 -5.256 1.211 3.00 1.21 0.04 303.00 103000.00 1.45 Max 37.20 1.17 156000.00 -1.840 1.34 157000.00 Min 35.20 1.02 65900.00 -7.950 1.07 51200.00 Limits 26.4 - 39.6 2.50 3030.00 ± 20 3.00 303.00 AVG STD Max Min Limits AVG STD Max Min Limits AVG STD Max Min Limits AVG STD Max Min 36.20 0.02 36.70 35.90 26.4 - 39.6 36.30 0.02 36.80 36.00 26.4 - 39.6 36.40 0.02 37.00 36.10 26.4 - 39.6 36.30 0.02 36.90 35.90 0.82 0.01 0.86 0.79 2.50 0.83 0.01 0.85 0.81 2.50 0.86 0.01 0.88 0.83 2.50 0.85 0.01 0.87 0.83 183000.00 1.11 227000.00 9870.00 3030.00 208000.00 1.03 2301000.00 188000.00 3030.00 141000.00 1.03 151000.00 131000.00 3030.00 217000.00 1.07 257000.00 193000.00 -5.708 0.595 -4.952 -7.065 ± 20 -1.354 0.194 -1.015 -2.033 ± 20 1.422 0.279 1.120 1.016 n/a 0.036 0.000 0.035 0.001 1.10 0.11 1.21 0.84 3.00 1.23 0.02 1.25 1.11 3.00 0.99 0.04 1.09 0.93 2.50 0.82 0.01 0.86 0.81 99900.00 1.46 143000.00 16200.00 303.00 98600.00 1.07 110000.00 85700.00 303.00 378000.00 2.20 1500000.00 102000.00 3030.00 72900.00 1.09 85100.00 61400.00 BUSINESS CONFIDENTIAL NO PORTION OF THIS REPORT MAY BE DISCLOSED TO ANY THIRD PARTY WITHOUT WRITTEN CONSENT OF KEMET ELECTRONICS CORPORATION KEMET Ceramic Surface Mount Capacitors High Voltage (≥ 500Vdc), ArcShield, X7R, 33nF, 630 Vdc, 1206 Case Size Qualification per Q-200 Rev. D and Results Summary - Lot Id. 0110T01006 Initial Readings Resistance to Soldering Heat Test Condition D. Pre-heat condition of 150°C, 60-120sec is allowed for ceramic components Mechanical Shock / Vibration Method 213: Figure 1, Condition F. Method 204: 12 cycles of 5 g for 20 minutes Limits AVG STD Max Min Limits AVG STD Max Min Capacitance, nF 26.4 - 39.6 36.80 0.05 37.40 34.40 26.4 - 39.6 36.90 0.02 37.30 36.60 DF, 120 Hz, % 2.50 1.15 0.02 1.17 1.06 2.50 1.14 0.02 1.18 1.09 Post Test Readings IR, 25°C, MOhm 3030.00 112000.00 1.31 133000.00 30.40 3030.00 123000.00 1.07 134000.00 104000.00 Delta Cap, % n/a -3.338 1.534 2.367 -5.732 n/a -0.104 0.200 0.319 -0.509 DF, 120 Hz, % 2.50 1.08 0.03 1.13 0.99 2.50 1.11 0.03 1.16 1.03 IR, 25°C, MOhm 3030.00 74900.00 1.19 89600.00 39600.00 3030.00 61600.00 1.05 66600.00 55700.00 Electrical Characterization Temperature Coefficient Characterization (TCC) KEMET Custom Test: Parametrically test, show statistics at room, min, and max operating temperatures. -55°C Delta Cap (%) Reference Capacitance @ 25°C, nF +125°C Delta Cap (%) IR, 125°C MOhm Limits ± 15 26.4 - 39.6 ± 15 303.00 AVG STD Max Min -8.99 0.43 -7.99 -9.75 36.70 0.03 37.10 36.70 -11.41 0.90 -10.23 -13.49 6087.91 1.14 7220.00 5020.00 Dimensions, mm Other Mechanical / Performance Results ESD, per AEC-Q200-002 Beam Load, per AEC-Q200-003, MPascal, MPa Class AVG STD Max Min 4 157 15 189 131 Limits AVG STD Max Min Length Width Thickness 3.0 - 3.4 3.32 0.02 3.36 3.28 1.4 - 1.8 1.69 0.04 1.77 1.62 1.5 - 1.9 1.59 0.03 1.66 1.53 BUSINESS CONFIDENTIAL NO PORTION OF THIS REPORT MAY BE DISCLOSED TO ANY THIRD PARTY WITHOUT WRITTEN CONSENT OF KEMET ELECTRONICS CORPORATION KEMET Ceramic Surface Mount Capacitors High Voltage (≥ 500Vdc), ArcShield, X7R, 68nF, 1000 Vdc, 1210 Case Size Qualification per Q-200 Rev. D and Results Summary - Lot Id. 0118T011806 Initial Readings High Temperature Life 125°C, 1.2x Rated Voltage, Hours 1000 Storage Life 125°C, 0 Volts, 1000 Hours Load Humidity 85°C, 85% RH, 200 Vdc max., 1000 Hours Low Volt Humidity 85°C, 85% RH, 1.5 Volts, 1000 Hours Temperature Cycle -55°C to +125°C, 1000 Cycles Post Test Readings Capacitance, nF DF, 120 Hz, % IR, 25°C, MOhm Delta Cap, % DF, 120 Hz, % IR, 25°C, MOhm Limits AVG STD 54.4 - 81.6 75.50 0.03 2.50 0.99 0.04 1471.00 16000.00 1.14 ± 20 -4.565 1.374 3.00 1.13 0.03 147.10 94000.00 1.71 Max 76.76 1.06 24000.00 -2.551 1.22 470000.00 Min 74.90 0.90 84800.00 -7.991 1.01 38800.00 Limits 54.4 - 81.6 2.50 1471.00 ± 20 3.00 147.10 AVG STD Max Min Limits AVG STD Max Min Limits AVG STD Max Min Limits AVG STD Max Min 74.40 0.03 75.20 73.70 54.4 - 81.6 74.90 0.05 75.90 72.30 54.4 - 81.6 74.80 0.04 75.70 73.80 54.4 - 81.6 74.90 0.03 75.80 74.30 0.78 0.01 0.82 0.77 2.50 0.85 0.02 0.89 0.81 2.50 0.85 0.01 0.87 0.82 2.50 0.85 0.02 0.89 0.82 181000.00 1.18 364000.00 105000.00 1471.00 164000.00 1.07 217000.00 136000.00 1471.00 161000.00 1.16 213000.00 56.10 1471.00 169000.00 1.07 192000.00 152000.00 -1.870 0.381 -1.563 -3.950 ± 20 -0.531 0.402 2.372 -1.264 ± 20 1.108 0.351 1.701 0.616 n/a -1.144 0.130 -0.882 -1.626 1.18 0.06 1.22 0.80 3.00 1.27 0.02 1.31 1.18 3.00 0.93 0.05 1.01 0.83 2.50 0.77 0.01 0.80 0.76 81500.00 1.14 95200.00 31200.00 147.10 67800.00 1.09 79700.00 59500.00 147.10 226000.00 2.57 1500000.00 62500.00 1471.00 545000.00 1.12 62200.00 44100.00 BUSINESS CONFIDENTIAL NO PORTION OF THIS REPORT MAY BE DISCLOSED TO ANY THIRD PARTY WITHOUT WRITTEN CONSENT OF KEMET ELECTRONICS CORPORATION KEMET Ceramic Surface Mount Capacitors High Voltage (≥ 500Vdc), ArcShield, X7R, 68nF, 1000 Vdc, 1210 Case Size Qualification per Q-200 Rev. D and Results Summary - Lot Id. 0118T011806 Initial Readings Resistance to Soldering Heat Test Condition D. Pre-heat condition of 150°C, 60-120sec is allowed for ceramic components Mechanical Shock / Vibration Method 213: Figure 1, Condition F. Method 204: 12 cycles of 5 g for 20 minutes Limits AVG STD Max Min Limits AVG STD Max Min Capacitance, nF 54.4 - 81.6 75.30 0.05 76.30 74.27 54.4 - 81.6 75.50 0.03 76.40 75.00 DF, 120 Hz, % 2.50 1.00 0.02 1.05 0.95 2.50 1.06 0.02 1.09 1.01 Post Test Readings IR, 25°C, MOhm 1471.00 54300.00 1.32 63900.00 20000.00 1471.00 56000.00 1.12 62000.00 42000.00 Delta Cap, % n/a -0.960 0.346 -0.405 -1.703 n/a -0.153 0.484 0.997 -1.115 DF, 120 Hz, % 2.50 1.06 0.04 1.12 0.90 2.50 0.98 0.06 1.10 0.89 IR, 25°C, MOhm 1471.00 61400.00 1.44 78300.00 1.59 1471.00 54900.00 1.09 61500.00 44500.00 Electrical Characterization Temperature Coefficient Characterization (TCC) KEMET Custom Test: Parametrically test, show statistics at room, min, and max operating temperatures. -55°C Delta Cap (%) Reference Capacitance @ 25°C, nF +125°C Delta Cap (%) IR, 125°C MOhm Limits ± 15 54.4 - 81.6 ± 15 147.10 AVG STD Max Min -9.65 0.50 -8.69 -11.44 73.80 0.03 74.50 73.30 -9.79 0.83 -8.35 -11.89 2971.97 1.06 3290.00 2670.00 Dimensions, mm Other Mechanical / Performance Results ESD, per AEC-Q200-002 Beam Load, per AEC-Q200-003, MPascal, MPa Class AVG STD Max Min 4 73 17 98 50 Limits AVG STD Max Min Length Width Thickness 2.9 - 3.7 3.30 0.06 3.34 3.03 2.3 - 2.7 2.57 0.03 2.64 2.51 2.05 - 2.45 2.33 0.03 2.38 2.27 BUSINESS CONFIDENTIAL NO PORTION OF THIS REPORT MAY BE DISCLOSED TO ANY THIRD PARTY WITHOUT WRITTEN CONSENT OF KEMET ELECTRONICS CORPORATION KEMET Ceramic Surface Mount Capacitors High Voltage (≥ 500Vdc), ArcShield, X7R, 0.33µF, 1000 Vdc, 1812 Case Size Qualification per Q-200 Rev. D and Results Summary - Lot Id. 0123T012310 Initial Readings High Temperature Life 125°C, 1.2x Rated Voltage, Hours 1000 Storage Life 125°C, 0 Volts, 1000 Hours Load Humidity 85°C, 85% RH, 200 Vdc max., 1000 Hours Low Volt Humidity 85°C, 85% RH, 1.5 Volts, 1000 Hours Temperature Cycle -55°C to +125°C, 1000 Cycles Post Test Readings Capacitance, µF DF, 120 Hz, % IR, 25°C, MOhm Delta Cap, % DF, 120 Hz, % IR, 25°C, MOhm Limits AVG STD 0.264 - 0.396 0.343 0.0012 2.50 1.20 0.02 303.00 5790.00 1.08 ± 20 -9.089 0.485 3.00 1.26 0.02 30.30 4570.00 1.12 Max 0.346 1.24 6360.00 -8.346 1.30 5550.00 Min 0.341 1.15 4370.00 -10.234 1.18 3840.00 Limits 0.264 - 0.396 2.50 303.00 ± 20 3.00 30.30 AVG STD Max Min Limits AVG STD Max Min Limits AVG STD Max Min Limits AVG STD Max Min 0.339 0.0013 0.343 0.337 0.264 - 0.396 0.339 0.0013 0.342 0.336 0.264 - 0.396 0.340 0.0012 0.344 0.338 0.264 - 0.396 0.340 0.0012 0.343 0.337 1.00 0.01 1.06 0.98 2.50 0.98 0.02 1.04 0.95 2.50 1.02 0.01 1.06 1.00 2.50 1.00 0.01 1.03 0.97 7350.00 1.05 8000.00 6700.00 303.00 6500.00 1.06 7080.00 4730.00 303.00 7380.00 1.21 10500.00 5930.00 303.00 6450.00 1.03 6800.00 6050.00 -9.384 0.772 -8.487 -10.552 ± 20 -7.597 1.120 -5.386 -11.190 ± 20 -0.007 0.228 0.282 -0.863 n/a -2.479 0.115 -2.220 -2.751 1.26 0.02 1.29 1.23 3.00 1.29 0.06 1.34 1.08 3.00 1.15 0.19 1.49 1.02 2.50 0.92 0.01 0.96 0.89 9410.00 1.20 12600.00 7140.00 30.30 6870.00 1.15 7590.00 2120.00 30.30 53100.00 2.92 789000.00 8870.00 303.00 5780.00 1.05 6260.00 5280.00 BUSINESS CONFIDENTIAL NO PORTION OF THIS REPORT MAY BE DISCLOSED TO ANY THIRD PARTY WITHOUT WRITTEN CONSENT OF KEMET ELECTRONICS CORPORATION KEMET Ceramic Surface Mount Capacitors High Voltage (≥ 500Vdc), ArcShield, X7R, 0.33µF, 1000 Vdc, 1812 Case Size Qualification per Q-200 Rev. D and Results Summary - Lot Id. 0123T012310 Initial Readings Resistance to Soldering Heat Test Condition D. Pre-heat condition of 150°C, 60-120sec is allowed for ceramic components Mechanical Shock / Vibration Method 213: Figure 1, Condition F. Method 204: 12 cycles of 5 g for 20 minutes Limits AVG STD Max Min Limits AVG STD Max Min Capacitance, µF 0.264 - 0.396 0.338 0.0011 0.340 0.336 0.264 - 0.396 0.339 0.0016 0.342 0.336 DF, 120 Hz, % 2.50 1.07 0.02 1.11 1.04 2.50 1.09 0.02 1.16 1.05 Post Test Readings IR, 25°C, MOhm 303.00 5320.00 1.05 5770.00 4880.00 303.00 5400.00 1.05 5850.00 4850.00 Delta Cap, % n/a -2.790 0.765 -0.620 -3.694 n/a 0.265 0.362 0.860 -0.590 DF, 120 Hz, % 2.50 1.20 0.02 1.24 1.13 2.50 1.12 0.05 1.20 0.99 IR, 25°C, MOhm 303.00 5670.00 1.06 6280.00 5040.00 303.00 4390.00 1.04 4720.00 4030.00 Electrical Characterization Temperature Coefficient Characterization (TCC) KEMET Custom Test: Parametrically test, show statistics at room, min, and max operating temperatures. -55°C Delta Cap (%) Reference Capacitance @ 25°C, µF +125°C Delta Cap (%) IR, 125°C MOhm Limits ± 15 0.264 - 0.396 ± 15 30.30 AVG STD Max Min -9.08 0.35 -8.10 -9.54 0.335 0.0014 0.338 0.332 -12.43 0.98 -11.01 -14.46 513.52 1.10 586.00 421.00 Dimensions, mm Other Mechanical / Performance Results ESD, per AEC-Q200-002 Beam Load, per AEC-Q200-003, MPascal, MPa Class AVG STD Max Min 4 181 22 226 150 Limits AVG STD Max Min Length Width Thickness 4.2 - 4.8 4.57 0.02 4.63 4.53 2.9 - 3.5 3.14 0.02 3.19 3.10 1.9 - 2.3 2.05 0.02 2.09 2.02 BUSINESS CONFIDENTIAL NO PORTION OF THIS REPORT MAY BE DISCLOSED TO ANY THIRD PARTY WITHOUT WRITTEN CONSENT OF KEMET ELECTRONICS CORPORATION KEMET Ceramic Surface Mount Capacitors High Voltage (≥ 500Vdc), ArcShield, Flexible Termination, X7R, 0.33µF, 630 Vdc, 2220 Case Size Qualification per Q-200 Rev. D and Results Summary - Lot Id. 1059T105903FT Initial Readings High Temperature Life 125°C, 1.2x Rated Voltage, Hours 1000 Storage Life 125°C, 0 Volts, 1000 Hours Load Humidity 85°C, 85% RH, 200 Vdc max., 1000 Hours Low Volt Humidity 85°C, 85% RH, 1.5 Volts, 1000 Hours Temperature Cycle -55°C to +125°C, 1000 Cycles Post Test Readings Capacitance, µF DF, 120 Hz, % IR, 25°C, MOhm Delta Cap, % DF, 120 Hz, % IR, 25°C, MOhm Limits AVG STD 0.264 - 0.396 0.338 0.001 2.50 1.18 0.01 303.00 20900.00 1.05 ± 20 -6.721 1.480 3.00 1.14 0.07 30.30 13200.00 1.26 Max 0.342 1.19 23400.00 -4.748 1.26 19800.00 Min 0.335 1.15 15900.00 -9.456 1.05 7190.00 Limits 0.264 - 0.396 2.50 303.00 ± 20 3.00 30.30 AVG STD Max Min Limits AVG STD Max Min Limits AVG STD Max Min Limits AVG STD Max Min 0.340 0.003 0.346 0.334 0.264 - 0.396 0.339 0.003 0.347 0.335 0.264 - 0.396 0.341 0.003 0.349 0.334 0.264 - 0.396 0.339 0.003 0.346 0.334 1.02 0.03 1.08 0.96 2.50 1.02 0.16 2.31 0.92 2.50 1.03 0.05 1.14 0.95 2.50 0.98 0.03 1.06 0.95 10800.00 1.06 11800.00 7140.00 303.00 11000.00 1.05 12300.00 8690.00 303.00 12400.00 1.03 13700.00 11500.00 303.00 12100.00 1.22 16900.00 3230.00 -4.218 0.497 -3.347 -5.270 ± 20 1.066 0.326 1.520 0.238 ± 20 0.112 0.315 0.780 -0.549 n/a -2.525 0.199 -2.179 -3.169 1.29 0.01 1.30 1.27 3.00 1.06 0.15 2.36 0.99 3.00 1.03 0.06 1.14 0.90 2.50 0.89 0.04 1.13 0.86 13100.00 1.43 23600.00 8500.00 30.30 5940.00 1.04 6570.00 4890.00 30.30 76400.00 5.40 1260000.00 352.00 303.00 6220.00 1.04 6700.00 5690.00 BUSINESS CONFIDENTIAL NO PORTION OF THIS REPORT MAY BE DISCLOSED TO ANY THIRD PARTY WITHOUT WRITTEN CONSENT OF KEMET ELECTRONICS CORPORATION KEMET Ceramic Surface Mount Capacitors High Voltage (≥ 500Vdc), ArcShield, Flexible Termination, X7R, 0.33µF, 630 Vdc, 2220 Case Size Qualification per Q-200 Rev. D and Results Summary - Lot Id. 1059T105903FT Initial Readings Resistance to Soldering Heat Test Condition D. Pre-heat condition of 150°C, 60-120sec is allowed for ceramic components Mechanical Shock / Vibration Method 213: Figure 1, Condition F. Method 204: 12 cycles of 5 g for 20 minutes Limits AVG STD Max Min Limits AVG STD Max Min Capacitance, µF 0.264 - 0.396 0.325 0.001 0.328 0.324 0.264 - 0.396 0.336 0.104 0.338 0.333 DF, 120 Hz, % 2.50 0.83 0.05 0.97 0.82 2.50 1.12 0.04 1.16 1.01 Post Test Readings IR, 25°C, MOhm 303.00 17000.00 1.51 34500.00 9700.00 303.00 14500.00 1.08 17700.00 12900.00 Delta Cap, % n/a 3.833 0.414 4.422 2.172 n/a -0.907 0.318 -0.390 -1.581 DF, 120 Hz, % 2.50 1.04 0.03 1.11 1.00 2.50 1.10 0.09 1.29 1.01 IR, 25°C, MOhm 303.00 8460.00 1.17 16800.00 5620.00 303.00 9740.00 1.09 11900.00 8480.00 Electrical Characterization Temperature Coefficient Characterization (TCC) KEMET Custom Test: Parametrically test, show statistics at room, min, and max operating temperatures. -55°C Delta Cap (%) Reference Capacitance @ 25°C, µF +125°C Delta Cap (%) IR, 125°C MOhm Limits ± 15 0.264 - 0.396 ± 15 30.30 AVG STD Max Min -8.51 0.60 -7.14 -9.55 0.326 0.002 0.329 0.323 -10.46 0.65 -9.74 -13.05 8530.00 0.00 1260.00 593.00 Dimensions, mm Other Mechanical / Performance Results ESD, per AEC-Q200-002 Beam Load, per AEC-Q200-003, MPascal, MPa Class AVG STD Max Min 4 1960 200 2283 1593 Limits AVG STD Max Min Length Width Thickness 5.15 - 6.65 5.85 0.01 5.86 5.84 4.60 - 5.40 4.94 0.02 4.98 4.93 2.30 - 2.70 2.53 0.01 2.54 2.51 BUSINESS CONFIDENTIAL NO PORTION OF THIS REPORT MAY BE DISCLOSED TO ANY THIRD PARTY WITHOUT WRITTEN CONSENT OF KEMET ELECTRONICS CORPORATION