HMC565


Design Assistance

Customised Pack Sizes / Qtys

Assembly Assistance

Support for all industry recognised
supply formats:

Die handling consultancy

Hi-Rel die qualification

Hot & Cold die probing

Electrical test & trimming
o Waffle Pack
o Gel Pak
o Tape & Reel

Onsite storage, stockholding &
scheduling

100% Visual Inspection
o MIL-STD 883 Condition A
o MIL-STD 883 Condition A

On-site failure analysis

Bespoke 24 Hour monitored
storage systems for secure long
term product support

On-site failure analysis
Contact
[email protected]
For price, delivery and to place orders
HMC565
www.analog.com
www.micross.com
Analog Devices Welcomes
Hittite Microwave Corporation
NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
www.analog.com
www.hittite.com
THIS PAGE INTENTIONALLY LEFT BLANK
HMC565
v02.0209
GaAs PHEMT MMIC LOW NOISE
AMPLIFIER, 6 - 20 GHz
LOW NOISE AMPLIFIERS - CHIP
1
Typical Applications
Features
The HMC565 is ideal for use as a LNA or driver amplifier for:
Noise Figure: 2.3 dB
• Point-to-Point Radios
OIP3: 20 dBm
• Point-to-Multi-Point Radios & VSAT
Single Supply: +3V @ 53 mA
• Test Equipment and Sensors
50 Ohm Matched Input/Output
• Military & Space
Small size: 2.53 x 0.98 x 0.10 mm
Functional Diagram
General Description
Gain: 22 dB
The HMC565 is a high dynamic range GaAs PHEMT
MMIC Low Noise Amplifier (LNA) chip which operates
from 6 to 20 GHz. The HMC565 features 22 dB of small
signal gain, 2.3 dB of noise figure and has a consistent
IP3 of 20 dBm across the operating band. This selfbiased LNA is ideal for hybrid and MCM assemblies
due to its compact size, wideband performance, single
+3V supply operation, and DC blocked RF I/O’s. All
data is measured with the chip in a 50 Ohm test
fixture connected via two 0.025 mm (1 mil) diameter
bondwires of minimal length 0.31 mm (12 mil).
Electrical Specifi cations, TA = +25° C, Vdd 1, 2, 3 = +3V
Parameter
Min.
Frequency Range
Gain
20
Gain Variation Over Temperature
Max.
Min.
Typ.
Max.
12 - 20
23
17
Units
GHz
21
dB
0.025
0.035
0.025
0.035
dB/ °C
Noise Figure
2.3
2.8
2.5
3.0
dB
Input Return Loss
15
12
Output Return Loss
15
10
dB
10
dBm
12
dBm
20
dBm
53
mA
Output Power for 1 dB Compression (P1dB)
7
Saturated Output Power (Psat)
Output Third Order Intercept (IP3)
Supply Current (Idd)(Vdd = +3V)
1 - 84
Typ.
6 - 12
10
7
12
17
20
53
17
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
dB
HMC565
v02.0209
GaAs PHEMT MMIC LOW NOISE
AMPLIFIER, 6 - 20 GHz
30
20
25
S21
S11
S22
0
20
15
-10
10
-20
5
-30
+25C
+85C
-55C
0
4
6
8
10
12
14
16
18
20
22
4
6
8
FREQUENCY (GHz)
14
16
18
20
22
Output Return Loss vs. Temperature
0
0
RETURN LOSS (dB)
+25C
+85C
-55C
-5
RETURN LOSS (dB)
12
FREQUENCY (GHz)
Input Return Loss vs. Temperature
-10
-15
-20
-25
+25C
+85C
-55C
-5
-10
-15
-20
4
6
8
10
12
14
16
18
20
4
22
6
8
FREQUENCY (GHz)
12
14
16
18
20
22
20
22
Reverse Isolation vs. Temperature
0
8
-10
ISOLATION (dB)
10
+25C
+85C
-55C
6
10
FREQUENCY (GHz)
Noise Figure vs. Temperature
NOISE FIGURE (dB)
10
LOW NOISE AMPLIFIERS - CHIP
30
10
1
Gain vs. Temperature
GAIN (dB)
RESPONSE (dB)
Broadband Gain & Return Loss
4
2
+25C
+85C
-55C
-20
-30
-40
-50
0
-60
4
6
8
10
12
14
16
FREQUENCY (GHz)
18
20
22
4
6
8
10
12
14
16
18
FREQUENCY (GHz)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
1 - 85
HMC565
v02.0209
Psat vs. Temperature
20
20
16
16
Psat (dBm)
P1dB (dBm)
P1dB vs. Temperature
12
8
+25C
+85C
-55C
4
12
8
+25C
+85C
-55C
4
0
0
4
6
8
10
12
14
16
18
20
22
4
6
8
10
FREQUENCY (GHz)
12
14
16
18
22
Power Compression @ 13 GHz
30
Pout (dBm), GAIN (dB), PAE(%)
25
25
20
15
+25C
+85C
-55C
10
5
4
6
8
10
12
14
16
18
20
20
10
5
0
-5
-25
22
Pout
Gain
PAE
15
-20
FREQUENCY (GHz)
-15
-10
INPUT POWER (dBm)
Gain, Noise Figure & Power vs.
Supply Voltage @ 13 GHz
10
25
8
20
Gain
7
6
15
P1dB
5
4
10
3
2
5
Noise Figure
1
0
0
2.5
NOISE FIGURE (dB)
GAIN (dB), P1dB (dBm)
9
3
3.5
Vdd (Vdc)
1 - 86
20
FREQUENCY (GHz)
Output IP3 vs. Temperature
OIP3 (dBm)
LOW NOISE AMPLIFIERS - CHIP
1
GaAs PHEMT MMIC LOW NOISE
AMPLIFIER, 6 - 20 GHz
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
-5
HMC565
v02.0209
GaAs PHEMT MMIC LOW NOISE
AMPLIFIER, 6 - 20 GHz
Drain Bias Voltage (Vdd1, Vdd2, Vdd3)
+3.5 Vdc
RF Input Power (RFIN)(Vdd = +3.0 Vdc)
0 dBm
Channel Temperature
175 °C
Continuous Pdiss (T= 85 °C)
(derate 8.9 mW/°C above 85 °C)
0.75 W
Thermal Resistance
(channel to die bottom)
119 °C/W
Storage Temperature
-65 to +150 °C
Operating Temperature
-55 to +85 °C
ESD Sensitivity (HBM)
Class 1A
Vdd (Vdc)
Idd (mA)
+2.5
51
+3.0
53
+3.5
55
Note: Amplifi er will operate over full voltage ranges shown
above.
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Outline Drawing
Die Packaging Information [1]
Standard
Alternate
GP-2 (Gel Pack)
[2]
[1] Refer to the “Packaging Information” section for die
packaging dimensions.
[2] For alternate packaging information contact Hittite
Microwave Corporation.
1
LOW NOISE AMPLIFIERS - CHIP
Typical Supply Current vs. Vdd
Absolute Maximum Ratings
NOTES:
1. ALL DIMENSIONS ARE IN INCHES [MM]
2. DIE THICKNESS IS .004”
3. TYPICAL BOND IS .004” SQUARE
4. BACKSIDE METALLIZATION: GOLD
5. BOND PAD METALLIZATION: GOLD
6. BACKSIDE METAL IS GROUND.
7. CONNECTION NOT REQUIRED FOR UNLABELED BOND PADS.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
1 - 87
HMC565
v02.0209
LOW NOISE AMPLIFIERS - CHIP
1
1 - 88
GaAs PHEMT MMIC LOW NOISE
AMPLIFIER, 6 - 20 GHz
Pad Descriptions
Pad Number
Function
Description
1
IN
This pad is AC coupled and matched to
50 Ohms from 6 - 20 GHz.
2, 3, 4
Vdd1, 2, 3
Power Supply Voltage for the amplifier. External bypass
capacitors of 100 pF and 0.1 μF are required.
5
OUT
This pad is AC coupled and matched to
50 Ohms from 6 - 20 GHz.
Die Bottom
GND
Die Bottom must be connected to RF/DC ground.
Interface Schematic
Assembly Diagram
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC565
GaAs PHEMT MMIC LOW NOISE
AMPLIFIER, 6 - 20 GHz
Mounting & Bonding Techniques for Millimeterwave GaAs MMICs
The die should be attached directly to the ground plane eutectically or with
conductive epoxy (see HMC general Handling, Mounting, Bonding Note).
50 Ohm Microstrip transmission lines on 0.127mm (5 mil) thick alumina thin film
substrates are recommended for bringing RF to and from the chip (Figure 1). If
0.254mm (10 mil) thick alumina thin film substrates must be used, the die should be
raised 0.150mm (6 mils) so that the surface of the die is coplanar with the surface
of the substrate. One way to accomplish this is to attach the 0.102mm (4 mil) thick
die to a 0.150mm (6 mil) thick molybdenum heat spreader (moly-tab) which is then
attached to the ground plane (Figure 2).
0.102mm (0.004”) Thick GaAs MMIC
Wire Bond
0.076mm
(0.003”)
RF Ground Plane
Microstrip substrates should be brought as close to the die as possible in order to
minimize bond wire length. Typical die-to-substrate spacing is 0.076mm (3 mils).
Handling Precautions
0.127mm (0.005”) Thick Alumina
Thin Film Substrate
Follow these precautions to avoid permanent damage.
Storage: All bare die are placed in either Waffle or Gel based ESD protective
containers, and then sealed in an ESD protective bag for shipment. Once the
sealed ESD protective bag has been opened, all die should be stored in a dry
nitrogen environment.
Cleanliness: Handle the chips in a clean environment. DO NOT attempt to clean
the chip using liquid cleaning systems.
Static Sensitivity: Follow ESD precautions to protect against > ± 250V ESD
strikes.
Transients: Suppress instrument and bias supply transients while bias is applied.
Use shielded signal and bias cables to minimize inductive pick-up.
General Handling: Handle the chip along the edges with a vacuum collet or with
a sharp pair of bent tweezers. The surface of the chip has fragile air bridges and
should not be touched with vacuum collet, tweezers, or fingers.
Figure 1.
0.102mm (0.004”) Thick GaAs MMIC
Wire Bond
0.076mm
(0.003”)
RF Ground Plane
1
LOW NOISE AMPLIFIERS - CHIP
v02.0209
0.150mm (0.005”) Thick
Moly Tab
Mounting
The chip is back-metallized and can be die mounted with AuSn eutectic preforms
or with electrically conductive epoxy. The mounting surface should be clean and
flat.
0.254mm (0.010”) Thick Alumina
Thin Film Substrate
Figure 2.
Eutectic Die Attach: A 80/20 gold tin preform is recommended with a work surface temperature of 255 °C and a tool temperature
of 265 °C. When hot 90/10 nitrogen/hydrogen gas is applied, tool tip temperature should be 290 °C. DO NOT expose the chip
to a temperature greater than 320 °C for more than 20 seconds. No more than 3 seconds of scrubbing should be required for
attachment.
Epoxy Die Attach: Apply a minimum amount of epoxy to the mounting surface so that a thin epoxy fillet is observed around the
perimeter of the chip once it is placed into position. Cure epoxy per the manufacturer’s schedule.
Wire Bonding
Ball or wedge bond with 0.025 mm (1 mil) diameter pure gold wire is recommended. Thermosonic wirebonding with a nominal stage
temperature of 150 °C and a ball bonding force of 40 to 50 grams or wedge bonding force of 18 to 22 grams is recommended. Use
the minimum level of ultrasonic energy to achieve reliable wirebonds. Wirebonds should be started on the chip and terminated on
the package or substrate. All bonds should be as short as possible <0.31 mm (12 mils).
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
1 - 89