Ceramic Molded Axial/Ra​dial Leaded C0G

MULTILAYER CERAMIC CAPACITORS/AXIAL
& RADIAL LEADED
Multilayer ceramic capacitors are available in a
variety of physical sizes and configurations, including
leaded devices and surface mounted chips. Leaded
styles include molded and conformally coated parts
with axial and radial leads. However, the basic
capacitor element is similar for all styles. It is called a
chip and consists of formulated dielectric materials
which have been cast into thin layers, interspersed
with metal electrodes alternately exposed on opposite
edges of the laminated structure. The entire structure is
fired at high temperature to produce a monolithic
block which provides high capacitance values in a
small physical volume. After firing, conductive
terminations are applied to opposite ends of the chip to
make contact with the exposed electrodes.
Termination materials and methods vary depending on
the intended use.
TEMPERATURE CHARACTERISTICS
Ceramic dielectric materials can be formulated with
Class III: General purpose capacitors, suitable
a wide range of characteristics. The EIA standard for
for by-pass coupling or other applications in which
ceramic dielectric capacitors (RS-198) divides ceramic
dielectric losses, high insulation resistance and
dielectrics into the following classes:
stability of capacitance characteristics are of little or
no importance. Class III capacitors are similar to Class
Class I: Temperature compensating capacitors,
II capacitors except for temperature characteristics,
suitable for resonant circuit application or other appliwhich are greater than ± 15%. Class III capacitors
cations where high Q and stability of capacitance charhave the highest volumetric efficiency and poorest
acteristics are required. Class I capacitors have
stability of any type.
predictable temperature coefficients and are not
affected by voltage, frequency or time. They are made
KEMET leaded ceramic capacitors are offered in
from materials which are not ferro-electric, yielding
the three most popular temperature characteristics:
superior stability but low volumetric efficiency. Class I
C0G: Class I, with a temperature coefficient of 0 ±
capacitors are the most stable type available, but have
30 ppm per degree C over an operating
the lowest volumetric efficiency.
temperature range of - 55°C to + 125°C (Also
known as “NP0”).
Class II: Stable capacitors, suitable for bypass
X7R: Class II, with a maximum capacitance
or coupling applications or frequency discriminating
change of ± 15% over an operating temperature
circuits where Q and stability of capacitance charrange of - 55°C to + 125°C.
acteristics are not of major importance. Class II
Z5U: Class III, with a maximum capacitance
capacitors have temperature characteristics of ± 15%
change of + 22% - 56% over an operating temor less. They are made from materials which are
perature range of + 10°C to + 85°C.
ferro-electric, yielding higher volumetric efficiency but
less stability. Class II capacitors are affected by
Specified electrical limits for these three temperature
temperature, voltage, frequency and time.
characteristics are shown in Table 1.
SPECIFIED ELECTRICAL LIMITS
Temperature Characteristics
Parameter
Dissipation Factor: Measured at following conditions.
C0G – 1 kHz and 1 vrms if capacitance >1000pF
1 MHz and 1 vrms if capacitance 1000 pF
X7R – 1 kHz and 1 vrms* or if extended cap range 0.5 vrms
Z5U – 1 kHz and 0.5 vrms
C0G
X7R
Z5U
0.10%
2.5%
(3.5% @ 25V)
4.0%
Dielectric Stength: 2.5 times rated DC voltage.
Pass Subsequent IR Test
Insulation Resistance (IR): At rated DC voltage,
whichever of the two is smaller
1,000 M
F
or 100 G
1,000 M
F
or 100 G
Temperature Characteristics: Range, °C
Capacitance Change without
DC voltage
-55 to +125
0 ± 30 ppm/°C
-55 to +125
± 15%
* MHz and 1 vrms if capacitance
1,000 M
or 10 G
100 pF on military product.
Table I
4
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
F
+ 10 to +85
+22%,-56%
APPLICATION NOTES FOR MULTILAYER
CERAMIC CAPACITORS
Polarity: Multilayer ceramic capacitors are not polar,
and may be used with DC voltage applied in either direction.
Rated Voltage: This term refers to the maximum continuous DC working voltage permissible across the entire
operating temperature range. Multilayer ceramic capacitors
are not extremely sensitive to voltage, and brief applications
of voltage above rated will not result in immediate failure.
However, reliability will be reduced by exposure to sustained
voltages above rated.
Capacitance: The standard unit of capacitance is the
farad. For practical capacitors, it is usually expressed in
microfarads (10-6 farad), nanofarads (10-9 farad), or picofarads
(10-12 farad). Standard measurement conditions are as
follows:
Class I (up to 1,000 pF):
1MHz and 1.2 VRMS
maximum.
Class I (over 1,000 pF):
1kHz and 1.2 VRMS
maximum.
Class II:
1 kHz and 1.0 ± 0.2 VRMS.
Class III:
1 kHz and 0.5 ± 0.1 VRMS.
Like all other practical capacitors, multilayer ceramic
capacitors also have resistance and inductance. A simplified
schematic for the equivalent circuit is shown in Figure 1.
Other significant electrical characteristics resulting from
these additional properties are as follows:
R
P
Figure 1
R
S
L
C
C = Capacitance
L = Inductance
R = Equivalent Series Resistance (ESR)
S
R = Insulation Resistance (IR)
P
Impedance: Since the parallel resistance (Rp) is normally very high, the total impedance of the capacitor is:
Z=
Where
2
RS + (XC - XL)
2
Z = Total Impedance
RS = Equivalent Series Resistance
XC = Capacitive Reactance =
1
2π
πfC
XL = Inductive Reactance = 2π
πfL
The variation of a capacitor’s impedance with frequency
determines its effectiveness in many applications.
Application Notes
ELECTRICAL CHARACTERISTICS
The fundamental electrical properties of multilayer
ceramic capacitors are as follows:
Dissipation Factor: Dissipation Factor (DF) is a measure of the losses in a capacitor under AC application. It is the
ratio of the equivalent series resistance to the capacitive reactance, and is usually expressed in percent. It is usually measured simultaneously with capacitance, and under the same
conditions. The vector diagram in Figure 2 illustrates the relationship between DF, ESR, and impedance. The reciprocal of
the dissipation factor is called the “Q”, or quality factor. For
convenience, the “Q” factor is often used for very low values
of dissipation factor. DF is sometimes called the “loss tangent”
or “tangent d”, as derived from this diagram.
ESR
Figure 2
O
DF = ESR
Xc
δ
X
c
Ζ
1
Xc =
2πfC
Insulation Resistance: Insulation Resistance (IR) is the
DC resistance measured across the terminals of a capacitor,
represented by the parallel resistance (Rp) shown in Figure 1.
For a given dielectric type, electrode area increases with
capacitance, resulting in a decrease in the insulation resistance. Consequently, insulation resistance is usually specified
as the “RC” (IR x C) product, in terms of ohm-farads or
megohm-microfarads. The insulation resistance for a specific
capacitance value is determined by dividing this product by
the capacitance. However, as the nominal capacitance values
become small, the insulation resistance calculated from the
RC product reaches values which are impractical.
Consequently, IR specifications usually include both a minimum RC product and a maximum limit on the IR calculated
from that value. For example, a typical IR specification might
read “1,000 megohm-microfarads or 100 gigohms, whichever
is less.”
Insulation Resistance is the measure of a capacitor to
resist the flow of DC leakage current. It is sometimes referred
to as “leakage resistance.” The DC leakage current may be
calculated by dividing the applied voltage by the insulation
resistance (Ohm’s Law).
Dielectric Withstanding Voltage: Dielectric withstanding voltage (DWV) is the peak voltage which a capacitor is
designed to withstand for short periods of time without damage. All KEMET multilayer ceramic capacitors will withstand a
test voltage of 2.5 x the rated voltage for 60 seconds.
KEMET specification limits for these characteristics at
standard measurement conditions are shown in Table 1 on
page 4. Variations in these properties caused by changing
conditions of temperature, voltage, frequency, and time are
covered in the following sections.
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
5
APPLICATION NOTES FOR MULTILAYER
CERAMIC CAPACITORS
TABLE 1
EIA TEMPERATURE CHARACTERISTIC CODES
FOR CLASS I DIELECTRICS
Significant Figure
of Temperature
Coefficient
Multiplier Applied
to Temperature
Coefficient
Tolerance of
Temperature
Coefficient *
PPM per
Degree C
Letter
Symbol
Multiplier
Number
Symbol
PPM per
Degree C
Letter
Symbol
0.0
0.3
0.9
1.0
1.5
2.2
3.3
4.7
7.5
C
B
A
M
P
R
S
T
U
-1
-10
-100
-1000
-100000
+1
+10
+100
+1000
+10000
0
1
2
3
4
5
6
7
8
9
±30
±60
±120
±250
±500
±1000
±2500
G
H
J
K
L
M
N
* These symetrical tolerances apply to a two-point measurement of
temperature coefficient: one at 25°C and one at 85°C. Some deviation
is permitted at lower temperatures. For example, the PPM tolerance
for C0G at -55°C is +30 / -72 PPM.
TABLE 2
EIA TEMPERATURE CHARACTERISTIC CODES
FOR CLASS II & III DIELECTRICS
6
Low Temperature
Rating
High Temperature Maximum Capacitance
Rating
Shift
Degree
Celcius
Letter
Symbol
Degree
Celcius
Number
Symbol
+10C
-30C
-55C
Z
Y
X
+45C
+65C
+85C
+105C
+125C
+150C
+200C
2
4
5
6
7
8
9
Percent
±1.0%
±1.5%
±2.2%
±3.3%
±4.7%
±7.5%
±10.0%
±15.0%
±22.0%
+22 / -33%
+22 / -56%
+22 / -82%
Letter
Symbol
A
B
C
D
E
F
P
R
S
T
U
V
+10
+20
+30
+40
+50
+60
+70
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
+80
APPLICATION NOTES FOR MULTILAYER
CERAMIC CAPACITORS
Application Notes
At higher AC voltages, both capacitance and dissipation factor
begin to decrease.
Typical curves showing the effect of applied AC and DC
voltage are shown in Figure 6 for KEMET X7R capacitors and
Figure 7 for KEMET Z5U capacitors.
Effect of Frequency: Frequency affects both capacitance and dissipation factor. Typical curves for KEMET multilayer ceramic capacitors are shown in Figures 8 and 9.
The variation of impedance with frequency is an important consideration in the application of multilayer ceramic
capacitors. Total impedance of the capacitor is the vector of the
capacitive reactance, the inductive reactance, and the ESR, as
illustrated in Figure 2. As frequency increases, the capacitive
reactance decreases. However, the series inductance (L)
shown in Figure 1 produces inductive reactance, which
increases with frequency. At some frequency, the impedance
ceases to be capacitive and becomes inductive. This point, at
the bottom of the V-shaped impedance versus frequency
curves, is the self-resonant frequency. At the self-resonant frequency, the reactance is zero, and the impedance consists of
the ESR only.
Typical impedance versus frequency curves for KEMET
multilayer ceramic capacitors are shown in Figures 10, 11, and
12. These curves apply to KEMET capacitors in chip form, without leads. Lead configuration and lead length have a significant
impact on the series inductance. The lead inductance is
approximately 10nH/inch, which is large compared to the
inductance of the chip. The effect of this additional inductance
is a decrease in the self-resonant frequency, and an increase
in impedance in the inductive region above the self-resonant
frequency.
Effect of Time: The capacitance of Class II and III
dielectrics change with time as well as with temperature, voltage and frequency. This change with time is known as “aging.”
It is caused by gradual realignment of the crystalline structure
of the ceramic dielectric material as it is cooled below its Curie
temperature, which produces a loss of capacitance with time.
The aging process is predictable and follows a logarithmic
decay. Typical aging rates for C0G, X7R, and Z5U dielectrics
are as follows:
C0G
X7R
Z5U
Effect of Temperature: Both capacitance and dissipation factor are affected by variations in temperature. The maximum capacitance change with temperature is defined by the
temperature characteristic. However, this only defines a “box”
bounded by the upper and lower operating temperatures and
the minimum and maximum capacitance values. Within this
“box”, the variation with temperature depends upon the specific dielectric formulation. Typical curves for KEMET capacitors are shown in Figures 3, 4, and 5. These figures also
include the typical change in dissipation factor for KEMET
capacitors.
Insulation resistance decreases with temperature.
Typically, the insulation resistance at maximum rated temperature is 10% of the 25°C value.
Effect of Voltage: Class I ceramic capacitors are not
affected by variations in applied AC or DC voltages. For Class
II and III ceramic capacitors, variations in voltage affect only
the capacitance and dissipation factor. The application of DC
voltage higher than 5 vdc reduces both the capacitance and
dissipation factor. The application of AC voltages up to 10-20
Vac tends to increase both capacitance and dissipation factor.
None
2.0% per decade of time
5.0% per decade of time
Typical aging curves for X7R and Z5U dielectrics are
shown in Figure 13.
The aging process is reversible. If the capacitor is heated to a temperature above its Curie point for some period of
time, de-aging will occur and the capacitor will regain the
capacitance lost during the aging process. The amount of deaging depends on both the elevated temperature and the
length of time at that temperature. Exposure to 150°C for onehalf hour or 125°C for two hours is usually sufficient to return
the capacitor to its initial value.
Because the capacitance changes rapidly immediately
after de-aging, capacitance measurements are usually delayed
for at least 10 hours after the de-aging process, which is often
referred to as the “last heat.” In addition, manufacturers utilize
the aging rates to set factory test limits which will bring the
capacitance within the specified tolerance at some future time,
to allow for customer receipt and use. Typically, the test limits
are adjusted so that the capacitance will be within the specified
tolerance after either 1,000 hours or 100 days, depending on
the manufacturer and the product type.
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
7
APPLICATION NOTES FOR MULTILAYER
CERAMIC CAPACITORS
POWER DISSIPATION
Power dissipation has been empirically determined for
two representative KEMET series: C052 and C062. Power dissipation capability for various mounting configurations is shown
in Table 3. This table was extracted from Engineering Bulletin
F-2013, which provides a more detailed treatment of this subject.
Note that no significant difference was detected between
the two sizes in spite of a 2 to 1 surface area ratio. Due to the
materials used in the construction of multilayer ceramic capacitors, the power dissipation capability does not depend greatly
on the surface area of the capacitor body, but rather on how
well heat is conducted out of the capacitor lead wires.
Consequently, this power dissipation capability is applicable to
other leaded multilayer styles and sizes.
TABLE 3
POWER DISSIPATION CAPABILITY
(Rise in Celsius degrees per Watt)
Mounting Configuration
Power
Dissipation
of C052 & C062
1.00" leadwires attached to binding post
of GR-1615 bridge (excellent heat sink)
90 Celsius degrees
rise per Watt ±10%
0.25" leadwires attached to binding post
of GR-1615 bridge
55 Celsius degrees
rise per Watt ±10%
Capacitor mounted flush to 0.062" glassepoxy circuit board with small copper traces
77 Celsius degrees
rise per Watt ±10%
Capacitor mounted flush to 0.062" glassepoxy circuit board with four square inches
of copper land area as a heat sink
53 Celsius degrees
rise per Watt ±10%
As shown in Table 3, the power dissipation capability of
the capacitor is very sensitive to the details of its use environment. The temperature rise due to power dissipation should not
exceed 20°C. Using that constraint, the maximum permissible
power dissipation may be calculated from the data provided in
Table 3.
It is often convenient to translate power dissipation capability into a permissible AC voltage rating. Assuming a sinusoidal wave form, the RMS “ripple voltage” may be calculated
from the following formula:
E=Zx
Where
PMAX
R
RELIABILITY
A well constructed multilayer ceramic capacitor is
extremely reliable and, for all practical purposes, has an infinite life span when used within the maximum voltage and
temperature ratings. Capacitor failure may be induced by sustained operation at voltages that exceed the rated DC voltage,
voltage spikes or transients that exceed the dielectric withstanding voltage, sustained operation at temperatures above
the maximum rated temperature, or the excessive temperature rise due to power dissipation.
Failure rate is usually expressed in terms of percent per
1,000 hours or in FITS (failure per billion hours). Some
KEMET series are qualified under U.S. military established
reliability specifications MIL-PRF-20, MIL-PRF-123, MILPRF-39014, and MIL-PRF-55681. Failure rates as low as
0.001% per 1,000 hours are available for all capacitance /
voltage ratings covered by these specifications. These specifications and accompanying Qualified Products List should
be consulted for details.
For series not covered by these military specifications,
an internal testing program is maintained by KEMET Quality
Assurance. Samples from each week’s production are subjected to a 2,000 hour accelerated life test at 2 x rated voltage
and maximum rated temperature. Based on the results of
these tests, the average failure rate for all non-military series
covered by this test program is currently 0.06% per 1,000
hours at maximum rated conditions. The failure rate would be
much lower at typical use conditions. For example, using MILHDBK-217D this failure rate translates to 0.9 FITS at 50%
rated voltage and 50°C.
Current failure rate details for specific KEMET multilayer ceramic capacitor series are available on request.
MISAPPLICATION
Ceramic capacitors, like any other capacitors, may fail
if they are misapplied. Typical misapplications include exposure to excessive voltage, current or temperature. If the
dielectric layer of the capacitor is damaged by misapplication
the electrical energy of the circuit can be released as heat,
which may damage the circuit board and other components
as well.
If potential for misapplication exists, it is recommended
that precautions be taken to protect personnel and equipment
during initial application of voltage. Commonly used precautions include shielding of personnel and sensing for excessive
power drain during board testing.
E = RMS Ripple Voltage (volts)
P = Power Dissipation (watts)
Z = Impedance
R = ESR
The data necessary to make this calculation is included in
Engineering Bulletin F-2013. However, the following criteria
must be observed:
1. The temperature rise due to power dissipation
should be limited to 20°C.
2. The peak AC voltage plus the DC voltage must not
exceed the maximum working voltage of the
capacitor.
Provided that these criteria are met, multilayer ceramic
8
capacitors may be operated with AC voltage applied without
need for DC bias.
STORAGE AND HANDLING
Ceramic chip capacitors should be stored in normal
working environments. While the chips themselves are quite
robust in other environments, solderability will be degraded
by exposure to high temperatures, high humidity, corrosive
atmospheres, and long term storage. In addition, packaging
materials will be degraded by high temperature – reels may
soften or warp, and tape peel force may increase. KEMET
recommends that maximum storage temperature not exceed
40˚ C, and maximum storage humidity not exceed 70% relative humidity. In addition, temperature fluctuations should be
minimized to avoid condensation on the parts, and atmospheres should be free of chlorine and sulfur bearing compounds. For optimized solderability, chip stock should be
used promptly, preferably within 1.5 years of receipt.
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
APPLICATION NOTES FOR MULTILAYER
CERAMIC CAPACITORS
IMPEDANCE VS FREQUENCY
0.20
100
Impedance vs. Frequency
Ceramic C0G
Leaded
.001μF
%ΔC
0.10
%DF
.01μF
100
%DF
-0.2
100
Figure 8.
1K
10K
100K
1M
0.0
10M
Frequency - Hertz
Capacitance & DF vs Frequency - C0G
Impedance (Ohms)
10
10.
Figure 10. Figure
-0.1
Impedance (Ohms)
%ΔC
+0.1
0
Application Notes
EFFECT OF FREQUENCY
+0.2
vs Frequency
ImpedanceImpedance
vs Frequency
for C0G Dielectric
for C0G Dielectric
10
1
0.001µF
1
0.1
10.
Figure 10. Figure
0.1
vs Frequency
vs 0.01µF
Frequency
ImpedanceImpedance
for C0G Dielectric
for C0G Dielectric
0.01
0.01 0.1
1
1 0
100
1000
Frequency - MHz
5.0
-10
2.5
-15
0.0
10M
100
1K
10K
100K
1M
Figure 9.
Frequency - Hertz
Capacitance & DF vs Frequency - X7R & Z5U
Figure 10.
Frequency - MHz
Impedance Impedance
vs Frequency
for C0G Dielectric
vs. Frequency
Leaded X7R
100
100
Impedance (Ohms)
%ΔC
%ΔC
-5
1,000
7.5
Impedance (Ohms)
%DF
0
Impedance
vs Frequency
Figure 10. Figure 10. Impedance vs
Frequency
10.0
0.001
for
C0G Dielectric
for
0.1
1 C0G Dielectric
10
100
%DF
+5
0.1μF
10
10
0.01µF
.01μF
0.1µF
1.0 μF
1
1.0µF Impedance
11. Impedance
vs Frequency
Figure 11. Figure
vs Frequency
1
0.1
for X7R Dielectric
for X7R Dielectric
EFFECT OF TIME (hours)
0.1
1
10
100
1000
Frequency - MHz
vs Frequency
Figure 11. Figure 11. ImpedanceImpedance
vs Frequency
0.01
for X7R Dielectric
for X7R Dielectric
X7R
X7R
Capacitance
Capacitance
0.001
0.1
1 Impedance vs.
10 Frequency
100
1,000
Z5U
Z5U
Impedance (Ohms)
Leaded Z5U
Figure
Impedance
vs Frequency
Figure 11.Figure
vs
Frequency
11.11.ImpedanceFrequency
- MHz
for X7Rfor
Dielectric
for
X7R
Dielectric
100
Impedance vs Frequency
X7R Dielectric
10
100
10
10
100
100
1000
1000
10K
10K
Figure 13. Typical Aging Rates for X7R & Z5U
100K
100K
Impedance (Ohms)
100%
100%
98%
98%
96%
96%
94%
94%
92%
92%
90%
90%
88%
88%
86%
86%
84%
84%
82%
82%
80%
80%
78%
78%
76%
76%
74%
74%
11
0.01
0.1
0.1µF
1
0.1μF
1.0µF
10
0.1
1.0 μF
0.01
1
0.1
1
1 0
100
1000
Frequency - MHz
vs Frequency
Figure 12. Figure 12. ImpedanceImpedance
vs Frequency
for Z5U Dielectric
for Z5U Dielectric
0.1
0.01
vs Frequency
Figure 12. Figure 12. ImpedanceImpedance
vs Frequency
for Z5U Dielectric
for Z5U Dielectric
0.001
0.1
1
10
100
1,000
Figure 12.
Frequency - MHz
Impedance vs Frequency for Z5U Dielectric
Impedance
vs Frequency
Figure 12. Figure 12.Impedance vs
Frequency
for Z5U Dielectric
for Z5U Dielectric
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
9
MIL-STD-202, Method 208, Sn62 solder, 245 C for
5 ±1/2 seconds.
CERAMIC MOLDED AXIAL & RADIAL
Terminal Strength:
PERFORMANCE CHARACTERISTICS
EIA-198 Method 303, Condition A (2.2 kg)
GENERAL SPECIFICATIONS
Working Voltage:
C0G – 50, 100, 200
X7R – 50, 100, 200
Temperature Characteristics:
C0G 0 ±30 PPM / °C from -55°C to +125°C
X7R ± 15% from -55°C to +125°C
Capacitance Tolerance:
C0G ±0.5pF, ±1%, ±2%, ±5%, ±10%, ±20%
(±0.5pF is tightest tolerance available)
X7R ±10%, ±20%, -0 +100%, +80% / -20%
Construction:
Monolithic block of ceramic dielectric with
Interdigitated internal electrodes, encapsulated
in a molded case, and having axial or radial leads.
Meets flame test requirements of UL Standard 94V-0.
ELECTRICAL
Capacitance:
Within specified tolerance and when measured with
1 volt rms at 1kHz (1000 pF or less at 1 MHz for C0G).
Dissipation Factor @25°C:
25°C at 1kHz (1000 pF or less at 1 MHz for C0G).
C0G – 0.15% maximum
X7R – 2.5% maximum
Insulation Resistance:
After 2 minutes electrification at 25°C and rated voltage
C0G – 100K M or 1000 M – F, whichever is less.
X7R – 100K M or 1000 M – F, whichever is less.
Dielectric Withstanding Voltage:
250% of rated voltage for 5 seconds with current limited
to 50 mA at 25°C.
Lead Material:
Axial: Solder coated copper clad steel
Radial: Solder-coated copper standard (100% tin
plated optional)
Solderability:
MIL-STD-202, Method 208, Sn62 solder, 245°C for
5 ±1/2 seconds.
Terminal Strength:
EIA-198 Method 303, Condition A (2.2 kg)
ELECTRICAL
Capacitance:
Within specified tolerance and when measured with
1 volt rms at 1kHz (1000 pF or less at 1 MHz for C0G).
Dissipation Factor @25°C:
25°C at 1kHz (1000 pF or less at 1 MHz for C0G).
C0G – 0.15% maximum
X7R – 2.5% maximum
Ceramic Molded
Axial/Radial - Standard
Insulation Resistance:
After 2 minutes electrification at 25°C and rated voltage
C0G – 100K M or 1000 M – F, whichever is less.
X7R – 100K M or 1000 M – F, whichever is less.
Dielectric Withstanding Voltage:
250% of rated voltage for 5 seconds with current limited
to 50 mA at 25°C.
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
27
CERAMIC MOLDED/AXIAL & RADIAL - STANDARD
CAPACITOR
(AXIALLEADS)
LEADS)
CAPACITOR OUTLINE DRAWINGS —
- (AXIAL
L
1.50 Min.
(38.10)
D
1.50 Min.
(38.10)
C
DIMENSIONS — INCHES (MILLIMETERS)
Case
Size
Military
Equivalent Styles
L
Length
D
Body diameter
C
Lead Diameter
C114
CC75, CCR75
CK12, CKR11
.160 ± .010 (4.06 ± .25)
.090 ± .010 (2.29 ± .25)
.020, +.000, -.003 (.51, +.00, -.08)
C124
CC76, CCR76
CK13, CKR12
.250 ± .010 (6.35 ± .25)
.090 ± .010 (2.29 ± .25)
.020, +.000, -.003 (.51, +.00, -.08)
C192
CC77, CCR77
CK14, CKR14
.390 ± .010 (9.91 ± .25)
.140 ± .010 (3.56 ± .25)
.025, +.004, -.001 (.64, +.10, -.025)
C202
CC78, CCR78
CK15, CKR15
.500 ± .020 (12.70 ± .51)
.250 ± .015 (6.35 ± .38)
.025, +.004, -.001 (.64, +.10, -.025)
C222
CC79, CCR79
CK16, CKR16
.690 ± .030 (17.53 ± .76)
.350 ± .020 (8.89 ± .51)
.025, +.004, -.001 (.64, +.10, -.025)
CAPACITOR OUTLINE DRAWINGS — (RADIAL LEADS)
CAPACITOR OUTLINE DRAWINGS - (RADIAL LEADS)
C052
L
W
H
1.25
Min.
Lead Dia.
.025
(+.004
-.002)
C062,
C512,
C522
.045
Max.
L
H
1.25
Min.
Center Line of leads
within .030" of Center
Line of case.
S
W
Lead Dia.
.025
(+.004
-.002)
S
DIMENSIONS — INCHES (MILLIMETERS)
Case
Size
C052
Military
Equivalent Styles
CC05, CCR05
CK05, CKR05
C062
CC06, CCR06
CK06, CKR06
C522
CC08, CCR08
C512
CC07, CCR07
S
Lead
Spacing
H
Height
L
Length
W
Width
.190 ± .010 (4.83 ± .25)
.190 ± .010 (4.83 ± .25)
.090 ± .010 (2.29 ± .25)
.200 ± .015 (5.08 ± .38)
.290 ± .010 (7.37 ± .25)
.290 ± .010 (7.37 ± .25)
.090 ± .010 (2.29 ± .25)
.200 ± .015 (5.08 ± .38)
.480 ± .020 (12.19 ± .51)
.240 ± .010 (6.10 ± .25)
.480 ± .020 (12.19 ± .51)
.480 ± .020 (12.19 ± .51)
.480 ± .020 (12.19 ± .51)
.140 ± .010 (3.56 ± .25)
.400 ± .020 (10.16 ± .51)
.400 ± .020 (10.16 ± .51)
For packaging information, see pages 46, 47 and 48.
28
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
CERAMIC MOLDED/AXIAL & RADIAL - STANDARD
C 052 C
CERAMIC
CASE SIZE
See Table Below
ORDERING INFORMATION
102
K
2
R
5
SPECIFICATION
C – Standard
CAPACITANCE PICOFARAD CODE
Expressed in picofarads (pF). First two digits represent
significant figures. Third digit specifies number of zeros
following except 9 indicates division by 10). Examples:
0.1 µF = 100,000 pF = 104 and 9.1 pF = 919. See
tables for standard values.
CAPACITANCE
Standard
M – ±20%
K – ±10%
J – ±5%
Axial
C114
C124
C192
C202
C222
FAILURE RATE
A – Not Applicable
LEAD MATERIAL
C – 60/40 Tin/Lead (SnPb)
T – 100% Tin (Sn)(C052,
C062 only)
INTERNAL CONSTRUCTION
5 – Multilayer
KEMET
EIA
Designator Equivalent
TOLERANCE
Others
H – ±3%
G – ±2%
F – ±1%
D – ±.5pF
Case Sizes
A
TEMPERATURE CHARACTERISTIC
G
(Ultra Stable)
R
(Stable)
Standard tolerances for each Series
are shown in the repetitive parts lists.
Radial
C052
C062
C512
C522
T
C0G
(NP0)
X7R
Cap. Change with Temp.
Measured
Temp
without DC
Range, °C
Bias Voltage
-55 to
±30
+125°
ppm/°C
-55° to
+125
±15%
WORKING VOLTAGE (DC)
2 – 200V; 1 – 100V; 5 – 50V
Part Number Example: C052C102K2R5TA (14 digits – no spaces)
AXIAL CAPACITOR MARKING
STANDARD C114C, C124C, C192C, C202C & C222C
KC0G
101J
200V
0812
KEMET, Temperature Characteristic
Capacitance, Capacitance Tolerance
Voltage
Date Code
RADIAL CAPACITOR MARKING
C052C & C062C STANDARD MARKING
C062
X7R
104K
BACK
100V
K
0811
Voltage
KEMET
Date Code
Ceramic Molded
Axial/Radial - Standard
FRONT
Style
Temperature Characteristic
Capacitance, Capacitance Tolerance
C512 & C522 STANDARD MARKING
KEMET
C512X7R
105K 50V
0832
KEMET
SIZE and Temperature Characteristic
Capacitance, Capacitance Tolerance, Voltage
Date Code
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
29
CERAMIC MOLDED/RADIAL – STANDARD
ULTRA-STABLE TEMPERATURE CHARACTERISTIC—C0G (NP0)
RATINGS & PART NUMBER REFERENCE
CAPACITANCE
pF
KEMET
PART NUMBER
CAPACITANCE
pF
200 VOLT – C114 STANDARD C0G
1.0
C114C109(1)2G5CA
1.5
C114C159(1)2G5CA
2.2
C114C229(1)2G5CA
2.7
C114C279(1)2G5CA
3.3
C114C339(1)2G5CA
3.9
C114C399(1)2G5CA
4.7
C114C479(1)2G5CA
5.6
C114C569(1)2G5CA
6.8
C114C689(1)2G5CA
8.2
C114C829(1)2G5CA
10.0
C114C100(2)2G5CA
12.0
C114C120(2)2G5CA
15.0
C114C150(2)2G5CA
18.0
C114C180(2)2G5CA
22.0
C114C220(2)2G5CA
27.0
C114C270(3)2G5CA
33.0
C114C330(3)2G5CA
39.0
C114C390(3)2G5CA
47.0
C114C470(3)2G5CA
56.0
C114C560(4)2G5CA
68.0
C114C680(4)2G5CA
82.0
C114C820(4)2G5CA
100.0
C114C101(4)2G5CA
120.0
C114C121(4)2G5CA
150.0
C114C151(4)2G5CA
180.0
C114C181(4)2G5CA
220.0
C114C221(4)2G5CA
270.0
C114C271(4)2G5CA
330.0
C114C331(4)2G5CA
100 VOLT – C114 STANDARD C0G
82.0
C114C820(4)1G5CA
100.0
C114C101(4)1G5CA
120.0
C114C121(4)1G5CA
150.0
C114C151(4)1G5CA
180.0
C114C181(4)1G5CA
220.0
C114C221(4)1G5CA
270.0
C114C271(4)1G5CA
330.0
C114C331(4)1G5CA
390.0
C114C391(4)1G5CA
470.0
C114C471(4)1G5CA
560.0
C114C561(4)1G5CA
680.0
C114C681(4)1G5CA
KEMET
PART NUMBER
CAPACITANCE
pF
200 VOLT – C124 STANDARD C0G
390.0
C124C391(4)2G5CA
470.0
C124C471(4)2G5CA
560.0
C124C561(4)2G5CA
200 VOLT – C202 STANDARD C0G
5,600.0
C202C562(4)2G5CA
6,800.0
C202C682(4)2G5CA
8,200.0
C202C822(4)2G5CA
10,000.0
C202C103(4)2G5CA
12,000.0
C202C123(4)2G5CA
15,000.0
C202C153(4)2G5CA
18,000.0
C202C183(4)2G5CA
22000.0
C202C223(4)2G5CA
100 VOLT – C124 STANDARD C0G
820.0
C124C821(4)1G5CA
1,000.0
C124C102(4)1G5CA
200 VOLT – C192 STANDARD C0G
680.0
C192C681(4)2G5CA
820.0
C192C821(4)2G5CA
1,000.0
C192C102(4)2G5CA
1,200.0
C192C122(4)2G5CA
1,500.0
C192C152(4)2G5CA
1,800.0
C192C182(4)2G5CA
2,200.0
C192C222(4)2G5CA
2,700.0
C192C272(4)2G5CA
3,300.0
C114C332(4)2G5CA
3,900.0
C114C392(4)2G5CA
4,700.0
C114C472(4)2G5CA
100 VOLT – C192 STANDARD C0G
1,200.0
C114C122(4)1G5CA
1,500.0
C114C152(4)1G5CA
1,800.0
C114C182(4)1G5CA
2,200.0
C114C222(4)1G5CA
2,700.0
C114C272(4)1G5CA
3,300.0
C114C332(4)1G5CA
3,900.0
C114C392(4)1G5CA
4,700.0
C114C472(4)1G5CA
5,600.0
C114C562(4)1G5CA
6,800.0
C114C682(4)1G5CA
8,200.0
C114C822(4)1G5CA
100 VOLT – C202 STANDARD C0G
10,000.0
C202C103(4)1G5CA
12,000.0
C202C123(4)1G5CA
15,000.0
C202C153(4)1G5CA
18,000.0
C202C183(4)1G5CA
22,000.0
C202C223(4)1G5CA
27,000.0
C202C273(4)1G5CA
33,000.0
C202C333(4)1G5CA
200 VOLT – C222 STANDARD C0G
27,000.0
C222C273(4)2G5CA
33,000.0
C222C333(4)2G5CA
39,000.0
C222C393(4)2G5CA
47,000.0
C222C473(4)2G5CA
100 VOLT – C222 STANDARD C0G
39,000.0
C222C393(4)1G5CA
47,000.0
C222C473(4)1G5CA
56,000.0
C222C563(4)1G5CA
68,000.0
C222C683(4)1G5CA
82,000.0
C222C823(4)1G5CA
100,000.0
C222C104(4)1G5CA
NOTE 1: Insert proper symbol for capacitance tolerance as
follows:
NOTE 1: Insert proper symbol for capacitance tolerance as
follows:
(1)
(2)
(3)
(4)
KEMET
PART NUMBER
1.0 pF to 8.2 pF: D— ±.5 pF
10.0 pF to 22 pF: J— ±5%, K— ±10%
27.0 pF to 47 pF: G— ±2%, J— ±5%, K— ±10%
56.0 pF and up: F— ±1%,G— ±2%, J— ±5%, K— ±10%
(1) 1.0 pF to 8.2 pF: D— ±.5 pF
(2) 10.0 pF to 22 pF: J— ±5%, K— ±10%
(3) 27.0 pF to 47 pF: G— ±2%, J— ±5%, K— ±10%
(4) 56.0 pF and up: F— ±1%,G— ±2%, J— ±5%, K— ±10%
NOTE 1: Insert proper symbol for capacitance tolerance as
follows:
(1)
(2)
(3)
(4)
30
1.0 pF to 8.2 pF: D— ±.5 pF
10.0 pF to 22 pF: J— ±5%, K— ±10%
27.0 pF to 47 pF: G— ±2%, J— ±5%, K— ±10%
56.0 pF and up: F— ±1%,G— ±2%, J— ±5%, K— ±10%
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
CERAMIC MOLDED/RADIAL – STANDARD
ULTRA-STABLE TEMPERATURE CHARACTERISTIC—C0G (NP0)
RATINGS & PART NUMBER REFERENCE
KEMET
PART NUMBER
CAPACITANCE
pF
200 VOLT – C062 SIZE C0G
3,300.0
C062C332(4)2G5CA
3,900.0
C062C392(4)2G5CA
4,700.0
C062C472(4)2G5CA
5,600.0
C062C562(4)2G5CA
6,800.0
C062C682(4)2G5CA
8,200.0
C062C822(4)2G5CA
10,000.0
C062C103(4)2G5CA
200 VOLT – C052 SIZE C0G
1.0
C052C109(1)2G5CA
1.5
C052C159(1)2G5CA
2.2
C052C229(1)2G5CA
2.7
C052C279(1)2G5CA
3.3
C052C339(1)2G5CA
3.9
C052C399(1)2G5CA
4.7
C052C479(1)2G5CA
5.6
C052C569(1)2G5CA
6.8
C052C689(1)2G5CA
8.2
C052C829(1)2G5CA
10.0
C052C100(2)2G5CA
12.0
C052C120(2)2G5CA
15.0
C052C150(2)2G5CA
18.0
C052C180(2)2G5CA
22.0
C052C220(2)2G5CA
27.0
C052C270(3)2G5CA
33.0
C052C330(3)2G5CA
39.0
C052C390(3)2G5CA
47.0
C052C470(3)2G5CA
56.0
C052C560(4)2G5CA
68.0
C052C680(4)2G5CA
82.0
C052C820(4)2G5CA
100.0
C052C101(4)2G5CA
120.0
C052C121(4)2G5CA
150.0
C052C151(4)2G5CA
180.0
C052C181(4)2G5CA
220.0
C052C221(4)2G5CA
270.0
C052C271(4)2G5CA
330.0
C052C331(4)2G5CA
390.0
C052C391(4)2G5CA
470.0
C052C471(4)2G5CA
560.0
C052C561(4)2G5CA
680.0
C052C681(4)2G5CA
820.0
C052C821(4)2G5CA
1,000.0
C052C102(4)2G5CA
1,200.0
C052C122(4)2G5CA
1,500.0
C052C152(4)2G5CA
1,800.0
C052C182(4)2G5CA
2,200.0
C052C222(4)2G5CA
2,700.0
C052C272(4)2G5CA
100 VOLT – C052 SIZE C0G
390.0
C052C391(4)1G5CA
470.0
C052C471(4)1G5CA
560.0
C052C561(4)1G5CA
680.0
C052C681(4)1G5CA
820.0
C052C821(4)1G5CA
1,000.0
C052C102(4)1G5CA
1,200.0
C052C122(4)1G5CA
1,500.0
C052C152(4)1G5CA
1,800.0
C052C182(4)1G5CA
2,200.0
C052C222(4)1G5CA
2,700.0
C052C272(4)1G5CA
3,300.0
C052C332(4)1G5CA
3,900.0
C052C392(4)1G5CA
4,700.0
C052C472(4)1G5CA
KEMET
PART NUMBER
100 VOLT – C062 SIZE C0G
5,600.0
C062C562(4)1G5CA
6,800.0
C062C682(4)1G5CA
8,200.0
C062C822(4)1G5CA
10,000.0
C062C103(4)1G5CA
12,000.0
C062C123(4)1G5CA
15,000.0
C062C153(4)1G5CA
18,000.0
C062C183(4)1G5CA
22,000.0
C062C223(4)1G5CA
200 VOLT – C512 SIZE C0G
12,000.0
C512C123(4)2G5CA
15,000.0
C512C153(4)2G5CA
18,000.0
C512C183(4)2G5CA
22,000.0
C512C223(4)2G5CA
27,000.0
C512C273(4)2G5CA
33,000.0
C512C333(4)2G5CA
39,000.0
C512C393(4)2G5CA
47,000.0
C512C473(4)2G5CA
56,000.0
C512C563(4)2G5CA
68,000.0
C512C683(4)2G5CA
100 VOLT – C512 SIZE C0G
27,000.0
C512C273(4)1G5CA
33,000.0
C512C333(4)1G5CA
39,000.0
C512C393(4)1G5CA
47,000.0
C512C473(4)1G5CA
56,000.0
C512C563(4)1G5CA
68,000.0
C512C683(4)1G5CA
82,000.0
C512C823(4)1G5CA
100,000.0
C512C104(4)1G5CA
200 VOLT – C522 SIZE C0G
82,000.0
C522C823(4)2G5CA
100,000.0
C522C104(4)2G5CA
100 VOLT – C522 SIZE C0G
120,000.0
C522C124(4)1G5CA
150,000.0
C522C154(4)1G5CA
180,000.0
C522C184(4)1G5CA
NOTE 1: Insert proper symbol for capacitance tolerance as
follows:
(1)
(2)
(3)
(4)
1.0 pF to 8.2 pF: D— ±.5 pF
10.0 pF to 22 pF: J— ±5%, K— ±10%
27.0 pF to 47 pF: G— ±2%, J— ±5%, K— ±10%
56.0 pF and up: F— ±1%,G— ±2%, J— ±5%, K— ±10%
Ceramic Molded
Axial/Radial - Standard
CAPACITANCE
pF
NOTE 1: Insert proper symbol for capacitance tolerance as
follows:
(1)
(2)
(3)
(4)
1.0 pF to 8.2 pF: D— ±.5 pF
10.0 pF to 22 pF: J— ±5%, K— ±10%
27.0 pF to 47 pF: G— ±2%, J— ±5%, K— ±10%
56.0 pF and up: F— ±1%,G— ±2%, J— ±5%, K— ±10%
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
31
CERAMIC LEADED
PACKAGING INFORMATION
CERAMIC PACKAGING
KEMET
Series
C114C-K-G
C124C-K-G
C192C-K-G
C202C-K
C222C-K
C052C-K-G
C062C-K-G
C114G
C124G
C192G
C202G
C222G
C052/56G
C062/66G
C512G
C522G
C114T
C124T
C192T
C202T
C222T
C052/56T
C062/66T
C31X
C32X
C33X
C340
C350
C410
C412
C420
C430
C440
C512
C522
C617
C622/C623
C627/C628
C630/C631
C637/C638
C640/C641
C642/C643
C647/C648
C657/C658
C667/C668
Military
Style
CK12, CC75
CK13, CC76
CK14, CC77
CK15
CK16
CK05, CC05
CK06, CC06
CCR75
CCR76
CCR77
CC78-CCR78
CC79-CCR79
CCR05
CCR06
CC07-CCR07
CC08-CCR08
CKR11
CKR12
CKR14
CKR15
CKR16
CKR05
CKR06
N/A
N/A
Military
Specification
MIL-C-11015/
MIL-PRF-20
MIL-PRF-20
MIL-PRF-39014
N/A
N/A
Standard (1)
Bulk
Quantity
200/Box
200/Box
100/Box
25/Box
10/Tray
100/Bag
100/Bag
200/Box
200/Box
100/Box
25/Box
10/Tray
100/Bag
100/Bag
Footnote (2)
Footnote (2)
200/Box
200/Box
100/Box
25/Box
10/Tray
100/Bag
100/Bag
500/Bag
500/Bag
250/Bag
100/Bag
50/Bag
300/Box
200/Box
300/Box
200/Box
200/Box
Footnote (2)
Footnote (2)
250/Bag
100/Bag
100/Bag
100/Bag
50/Bag
50/Bag
50/Bag
50/Bag
50/Bag
50/Bag
Ammo Pack
Quantity
Maximum
2000
1500
2500
2500
1500
1000
N/A
4000
4000
4000
2000
2000
Maximum
Reel
Quantity
5000
5000
3000
500
300
2000
1500
5000
5000
3000
500
300
1700
1500
N/A
N/A
5000
5000
3000
500
300
1700
1500
2500
2500
1500
1000
500
5000
5000
5000
2500
2500
N/A
N/A
1000
500
500
500
500
500
500
500
500
500
NOTE: (1) Standard packaging refers to number of pieces per bag, tray or vial.
(2) Quantity varies. For further details, please consult the factory.
48
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
Reel
Size
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
N/A
N/A
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
N/A
N/A
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
Tape & Reel Packaging Information
KEMET offers standard reeling of Molded and Conformally
Coated Radial Leaded Capacitors in accordance with EIA
standard 468. Parts are taped to a tagboard carrier strip, and
wound on a reel as shown in Figure 1. Kraft paper interleaving is
inserted between the layers of capacitors on the reel. Ammopack
is also available, with the same lead tape configuration and
package quantities.
t
Ceramic Radial Tape and Reel Dimensions
Metric will govern
Constant Dimensions — Millimeters (Inches)
D0
±0.2 (0.008)
P0
±0.3 (0.012)
ΔH
±0.2 (0.008)
L1
Maximum
t
±0.2 (0.008)
T
Maximum
W
+ 1.0/- 0.5
(+0.039/-0.020)
W0
Minimum
W2
Maximum
4.00 (0.157)
12.7 (0.500)
4.0 (0.157)
1.0 (0.039)
0.7 (0.051)
1.5 (0.059)
18.0 (0.709)
5.0 (0.197)
3.0 (0.118)
Ceramic Radial Tape and Reel Dimensions cont'd
Metric will govern
Variable Dimensions — Millimeters (Inches)
F
±0.030 (0.78)
Note 1
P1
±0.030 (0.012)
Note 1
P
±0.3 (0.012)
P2
±1.3 (0.51)
2.54 (0.100)
5.08 (0.200)
12.7 (0.500)
6.35 (0.250)
4.32 (0.170)
3.89 (0.153)
12.7 (0.500)
6.35 (0.250)
5.08 (0.200)
3.81 (0.150)
12.7 (0.500)
6.35 (0.250)
5.59 (0.220)
3.25 (0.128)
12.7 (0.500)
6.35 (0.250)
6.98 (0.275)
2.54 (0.100)
12.7 (0.500)
6.35 (0.250)
7.62 (0.300)
2.24 (0.088)
12.7 (0.500)
6.35 (0.250)
9.52 (0.375)
7.62 (0.300)
12.7 (0.500)
6.35 (0.250)
10.16 (0.400)
7.34 (0.290)
25.4 (1.000)
N/A
12.06 (0.475)
6.35 (0.250)
25.4 (1.000)
N/A
14.60 (0.575)
5.08 (0.200)
25.4 (1.000)
N/A
17.14 (0.675)
3.81 (0.15)
25.4 (1.000)
N/A
1.Measuredattheegressfromthecarriertape,onthecomponentside.
2.StraightLeadconfigurationparttypesonly.
3.Formed(bent)leadconfigurationparttypesonly.
Symbol Reference Table
D0
P0
P
F
P1
P2
H
H0
H1
ΔH
L1
t
W
W0
W2
Sprocket Hole Diameter
Sprocket Hole Pitch
Component Pitch
Lead Spacing
Sprocket Hole Center to Lead Center
Sprocket Hole Center To Component Center
Height to Seating Plane (Straight Leads Only)
Height to Seating Plane (Formed Leads Only)
Component Height Above Tape Center
Component Alignment
Lead Protrusion
Composite Tape Thickness
Carrier Tape Width
Hold-Down Tape Width
Hold-Down Tape Location
H
Minimum
Note 2
H0
±0.5 (0.630)
Note 3
18.0 (0.709)
16.0 (0.024)
Tape & Reel Packaging Information
KEMET offers standard reeling of molded and conformally
coated axial leaded ceramic capacitors for automatic insertion
or lead forming machines in accordance with EIA standard 296.
KEMET’sinternalspecificationfour-digitsuffix,7200,isplacedat
the end of the part number to designate tape and reel packaging,
e.g.,C410C104Z5U5CA7200.
Paper (50 lb.) test minimum is inserted between the layers
ofcapacitorswoundonreelsforcomponentpitch≤0.400".
Capacitor lead length may extend only a maximum of .0625"
(1.59 mm) beyond the tapes’ edges. Capacitors are centered in
a row between the two tapes and will deviate only ± 0.031" (0.79
mm) from the row center. A minimum of 36" (91.5 cm) leader
tapeisprovidedateachfinishedlengthoftapedcomponents.
Universalsplicingclipsareusedtoconnectthetape.
Table 3 – Ceramic Axial Tape and Reel Dimensions
Metric will govern
Dimensions — Millimeters (Inches)
Axial Capacitor
Body Diameter
0.0 to 5.0
(0.0 to 0.197)
A
±0.5 (0.020)
B
±1.5 (0.059)*
5.0 (0.197)
52.4 (2.062)
Symbol Reference Table
A
B
* Inside tape spacing dimension (B) is determined by the body diameter of the capacitor.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
Component Pitch
Inside Tape Spacing
KEMET Corporation
World Headquarters
Europe
Asia
Southern Europe
Sasso Marconi, Italy
Tel:39-051-939111
Northeast Asia
Hong Kong
Tel:852-2305-1168
MailingAddress:
P.O. Box 5928
Greenville, SC 29606
Skopje, Macedonia
Tel:389-2-55-14-623
Shenzhen, China
Tel:86-755-2518-1306
www.kemet.com
Tel:864-963-6300
Fax:864-963-6521
Central Europe
Landsberg, Germany
Tel:49-8191-3350800
Corporate Offices
Fort Lauderdale, FL
Tel:954-766-2800
Kamen, Germany
Tel:49-2307-438110
North America
Northern Europe
Wyboston,UnitedKingdom
Tel:44-1480-273082
Taipei, Taiwan
Tel:886-2-27528585
Espoo, Finland
Tel:358-9-5406-5000
Southeast Asia
Singapore
Tel:65-6701-8033
2835 KEMET Way
Simpsonville, SC 29681
Southeast
Lake Mary, FL
Tel:407-855-8886
Northeast
Wilmington, MA
Tel:978-658-1663
Central
Novi, MI
Tel:248-994-1030
Beijing, China
Tel:86-10-5877-1075
Shanghai, China
Tel:86-21-6447-0707
Seoul, South Korea
Tel:82-2-6294-0550
Penang, Malaysia
Tel:60-4-6430200
Bangalore, India
Tel:91-806-53-76817
West
Milpitas, CA
Tel:408-433-9950
Mexico
Guadalajara, Jalisco
Tel:52-33-3123-2141
Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not
assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of
KEMET Electronics Corporation.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
Disclaimer
Allproductspecifications,statements,informationanddata(collectively,the“Information”)inthisdatasheetaresubjecttochange.Thecustomerisresponsibleforcheckingand
verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed.
All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied.
Statements of suitability for certain applications are based on KEMET Electronics Corporation’s (“KEMET”) knowledge of typical operating conditions for such applications, but are
notintendedtoconstitute–andKEMETspecificallydisclaims–anywarrantyconcerningsuitabilityforaspecificcustomerapplicationoruse.TheInformationisintendedforuseonly
by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise
provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained.
Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still
occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective
circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage.
Althoughallproduct–relatedwarnings,cautionsandnotesmustbeobserved,thecustomershouldnotassumethatallsafetymeasuresareindictedorthatothermeasuresmaynot
be required.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com