Switching Thyristors Sx01E and SxN1 Datasheet

Teccor® brand Thyristors
1 Amp Standard SCRs
Sx01E & SxN1 Series
RoHS
Description
Excellent for lower current heat, lamp, and audible alarm
controls for home goods.
Standard phase control SCRs are triggered with few
milliamperes of current at less than 1.5V potential.
Features & Benefits
• RoHS compliant
• Voltage capability up
to 600 V
• Glass – passivated
junctions
• Surge capability up to
30 A
Applications
Main Features
Symbol
IT(RMS)
VDRM /VRRM
IGT
Value
Unit
1
A
400 to 600
V
10
mA
Typical applications are AC solid-state switches,
fluidlevel sensors, strobes, and capacitive-discharge
ignition systems.
Additional Information
Schematic Symbol
Datasheet
A
Samples
Resources
K
G
Absolute Maximum Ratings — Standard SCRs
Parameter
Test Conditions
Value
Unit
IT(RMS)
Symbol
RMS on-state current
TC = 90°C
1
A
IT(AV)
Average on-state current
TC = 90°C
0.64
A
single half cycle; f = 50Hz;
TJ (initial) = 25°C
25
single half cycle; f = 60Hz;
TJ (initial) = 25°C
30
3.7
A2s
A/μs
ITSM
Peak non-repetitive surge current
I 2t
I2t Value for fusing
tp = 8.3 ms
Critical rate of rise of on-state current
f = 60Hz ; TJ = 125°C
50
Peak gate current
TJ = 125°C
1.5
A
Average gate power dissipation
TJ = 125°C
0.3
W
Storage temperature range
-40 to 150
°C
Operating junction temperature range
-40 to 125
°C
di/dt
IGM
PG(AV)
Tstg
TJ
A
© 2016 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 05/02/16
Teccor® brand Thyristors
1 Amp Standard SCRs
Electrical Characteristics (TJ = 25°C, unless otherwise specified)
Symbol
Test Conditions
IGT
VD = 12V; RL = 60 Ω
VGT
VD = 12V; RL = 60 Ω
dv/dt
Value
VD = VDRM; gate open; TJ = 100°C
MAX.
10
MIN.
1
MAX.
1.5
20
MIN.
VD = VDRM; gate open; TJ = 125°C
40
Unit
mA
V
V/μs
VGD
VD = VDRM; RL = 3.3 kΩ; TJ = 125°C
MIN.
0.2
V
IH
IT = 200mA (initial)
MAX.
30
mA
tq
(1)
MAX.
35
μs
tgt
IG = 2 x IGT; PW = 15µs; IT = 2A
TYP.
2
μs
(1) IT=1A; tp=50µs; dv/dt=20V/µs; di/dt=-10A/µs
Static Characteristics
Symbol
VTM
Test Conditions
IT = 2A; tp = 380 µs
Value
Unit
1.6
V
MAX.
TJ = 25°C
IDRM / IRRM
VDRM = VRRM
10
TJ = 100°C
200
MAX.
TJ = 125°C
μA
500
Thermal Resistances
Symbol
Parameter
Rθ(J-C)
Junction to case (AC)
Rθ(J-A)
Junction to ambient
Notes : x = voltage
* = Mounted on 1 cm2 copper (two-ounce) foil surface
© 2016 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 05/02/16
Value
Sx01E
50
SxN1
35*
Sx01E
145
Unit
°C/W
°C/W
Teccor® brand Thyristors
1 Amp Standard SCRs
Figure 1: Normalized DC Gate Trigger Current
vs. Junction Temperature
Figure 2: N
ormalized DC Gate Trigger Voltage
vs. Junction Temperature
2.0
Ratio of VGT / VGT (TJ = 25°C)
Ratio of IGT / IGT (TJ = 25°C)
2.0
1.5
1.0
0.5
0.0
-40
-15
10
35
60
85
110
1.5
1.0
0.5
0.0
125
-40
-15
10
Figure 3: Normalized DC Holding Current
vs. Junction Temperature
Instantaneous On-state Current (iT) – Amps
Ratio of IH/IH (TJ = 25°C)
60
85
110
125
Figure 4: O
n-State Current vs. On-State
Voltage (Typical)
2.0
1.5
1.0
0.5
25
TJ = 25°C
20
15
10
5
0
0.0
-40
-15
10
35
60
85
110
0.7
125
0.8
Figure 5: Power Dissipation (Typical)
vs. RMS On-State Current
Maximum Allowable Case Temperature (TC) - °C
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
0.1
0.2
0.3
0.4
0.5
0.6
1.0
1.1
1.2
1.3
1.4
1.5
1.6
Figure 6: Maximum
Allowable Case Temperature
vs. RMS On-State Current
1.0
0.0
0.9
Instantaneous On-state Voltage (vT) – Volts
Junction Temperature (TJ) -- (°C)
Average On-State Power Dissipation [PD(AV)] - (Watts)
35
Junction Temperature (TJ) -- (°C)
Junction Temperature (TJ) -- (°C)
0.7
RMS On-State Current [IT(RMS)] - Amps
0.8
0.9
1.0
130
125
120
115
110
105
100
95
90
CURRENT WAVEFORM: Sinusoidal
LOAD: Resistive or Inductive
CONDUCTION ANGLE: 180°
85
80
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
1.1
RMS On-State Current [IT(RMS)] - Amps
© 2016 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 05/02/16
Teccor® brand Thyristors
1 Amp Standard SCRs
Figure 8: Maximum Allowable Ambient Temperature
vs. RMS On-State Current
130
Maximum Allowable Ambient Temperature (TA) - °C
Maximum Allowable Case Temperature (TC) - °C
Figure 7: Maximum Allowable Case Temperature
vs. Average On-State Current
125
120
115
110
105
100
95
90
CURRENT WAVEFORM: Sinusoidal
LOAD: Resistive or Inductive
CONDUCTION ANGLE: 180°
85
80
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
120
CURRENT WAVEFORM: Sinusoidal
LOAD: Resistive or Inductive
CONDUCTION ANGLE: 180°
FREE AIR RATING
100
80
60
40
20
0
0.8
0.0
0.1
0.2
Figure 9: Maximum Allowable Ambient Temperature
vs. Average On-State Current
0.4
0.5
0.6
0.7
0.8
0.9
1.0
Figure 10: Peak Capacitor Discharge Current
100
CURRENT WAVEFORM: Sinusoidal
LOAD: Resistive or Inductive
CONDUCTION ANGLE: 180°
FREE AIR RATING
100
80
60
40
20
Peak Discharge Current (ITM) - Amps
Maximum Allowable Ambient Temperature
(TA) - °C
120
10
ITRM
tW
0
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
Figure 11: Peak Capacitor Discharge Current Derating
1.2
1.0
0.8
0.6
0.4
0.2
0.0
0
25
50
75
100
Case Temperature (TC) - °C
© 2016 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 05/02/16
125
1
0.5
1.0
10.0
Pulse Current Duration (tW) - ms
Average On-State Current [IT(AVE)] - Amps
Normalized Peak Current
0.3
RMS On-State Current [IT(RMS)] - Amps
Average On-State Current [IT(AVE)] - Amps
150
50.0
Teccor® brand Thyristors
1 Amp Standard SCRs
Figure 12: Surge Peak On-State Current vs. Number of Cycles
Peak Surge (Non-repetitive)
On-state Current (ITSM) – Amps
100.0
SUPPLY FREQUENCY: 60 Hz Sinusoidal
LOAD: Resistive
RMS On-State Current: [IT(RMS)]: Maximum Rated
Value at Specified Case Temperature
Notes:
1. G
ate control may be lost during and immediately
following surge current interval.
2. O
verload may not be repeated until junction
temperature has returned to steady-state
rated value.
10.0
1.0
0.1
1
10
100
1000
Surge Current Duration -- Full Cycles
Soldering Parameters
Pre Heat
Pb – Free assembly
- Temperature Min (Ts(min))
150°C
- Temperature Max (Ts(max))
200°C
- Time (min to max) (ts)
60 – 180 secs
Average ramp up rate (Liquidus Temp)
(TL) to peak
5°C/second max
TS(max) to TL - Ramp-up Rate
5°C/second max
Reflow
- Temperature (TL) (Liquidus)
217°C
- Temperature (tL)
60 – 150 seconds
260
Time within 5°C of actual peak
Temperature (tp)
20 – 40 seconds
Ramp-up
TL
tL
TS(max)
Preheat
TS(min)
25
Peak Temperature (TP)
+0/-5
tP
TP
Temperature
Reflow Condition
Ramp-do
Ramp-down
tS
time to peak temperature
Time
°C
Ramp-down Rate
5°C/second max
Time 25°C to peak Temperature (TP)
8 minutes Max.
Do not exceed
280°C
© 2016 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 05/02/16
Teccor® brand Thyristors
1 Amp Standard SCRs
Physical Specifications
Environmental Specifications
Test
Terminal Finish
100% Matte Tin-plated
Body Material
UL recognized epoxy meeting flammability
classification 94V-0
Lead Material
Copper Alloy
Specifications and Conditions
AC Blocking
Temperature Cycling
Temperature/
Humidity
MIL-STD-750, M-1040, Cond A Applied
Peak AC voltage @ 125°C for 1008 hours
MIL-STD-750, M-1051,
100 cycles; -40°C to +150°C; 15-min
dwell-time
EIA / JEDEC, JESD22-A101
1008 hours; 320V - DC: 85°C; 85%
rel humidity
MIL-STD-750, M-1031,
1008 hours; 150°C
Design Considerations
High Temp Storage
Careful selection of the correct device for the application’s
operating parameters and environment will go a long way
toward extending the operating life of the Thyristor. Good
design practice should limit the maximum continuous
current through the main terminals to 75% of the device
rating. Other ways to ensure long life for a power discrete
semiconductor are proper heat sinking and selection of
voltage ratings for worst case conditions. Overheating,
overvoltage (including dv/dt), and surge currents are
the main killers of semiconductors. Correct mounting,
soldering, and forming of the leads also help protect
against component damage.
Low-Temp Storage
1008 hours; -40°C
Resistance to
Solder Heat
MIL-STD-750 Method 2031
Solderability
ANSI/J-STD-002, category 3, Test A
Lead Bend
MIL-STD-750, M-2036 Cond E
Dimensions – TO-92 (E Package)
TC Measuring Point
A
B
Cathode
Anode
Gate
Inches
Millimeters
Min
Max
Min
Max
A
0.176
0.196
4.47
4.98
B
0.500
D
0.095
E
0.150
12.70
0.105
2.41
H
M
F
D
K
J
© 2016 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 05/02/16
G
2.67
3.81
F
0.046
0.054
1.16
1.37
G
0.135
0.145
3.43
3.68
H
0.088
0.096
2.23
2.44
J
0.176
0.186
4.47
4.73
K
0.088
0.096
2.23
2.44
L
0.013
0.019
0.33
0.48
M
0.013
0.017
0.33
0.43
All leads insulated from case. Case is electrically nonconductive.
E
L
Dimension
Teccor® brand Thyristors
1 Amp Standard SCRs
Dimensions - Compak (C Package)
TC / TL Temperature
Measurement Point
M
A
Dimension
Gate
B
D
A
N
P
C
Cathode
Anode
F
H
L
E
J
0.079
(2.0)
K
0.079
(2.0)
G
0.079
(2.0)
0.040
(1.0)
0.030
(0.76)
0.110
(2.8)
Inches
Millimeters
Min
Max
Min
Max
0.130
0.156
3.30
3.95
B
0.201
0.220
5.10
5.60
C
0.077
0.087
1.95
2.20
D
0.159
0.181
4.05
4.60
E
0.030
0.063
0.75
1.60
F
0.075
0.096
1.90
2.45
G
0.002
0.008
0.05
0.20
H
0.077
0.104
1.95
2.65
J
0.043
0.053
1.09
1.35
K
0.006
0.016
0.15
0.41
L
0.030
0.055
0.76
1.40
M
0.022
0.028
0.56
0.71
N
0.027
0.033
0.69
0.84
P
0.052
0.058
1.32
1.47
Dimensions are in inches
(and millimeters).
Pad Outline
Product Selector
Part Number
Voltage
400V
600V
800V
1000V
Gate Sensitivity
Type
Package
Sx01E
X
X
10mA
Standard SCR
TO-92
SxN1
X
X
10mA
Standard SCR
Compak
Note: x = Voltage
Packing Options
Marking
Weight
Packing Mode
Base Quantity
Sx01E
Part Number
Sx01E
0.19 g
Bulk
2000
Sx01ERP
Sx01E
0.19 g
Reel Pack
2000
Sx01EAP
Sx01E
0.19 g
Ammo Pack
2000
SxN1RP
SxN1
0.08 g
Embossed Carrier
2500
Note: x = Voltage
© 2016 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 05/02/16
Teccor® brand Thyristors
1 Amp Standard SCRs
TO-92 (3-lead) Reel Pack (RP) Radial Leaded Specifications
Meets all EIA-468-C Standards
1.6
(41.0)
0.236
(6.0)
0.708
(18.0)
0.02 (0.5)
0.098 (2.5) MAX
1.26
(32.0)
0.354
(9.0)
0.5
(12.7)
0.1 (2.54)
Cathode
0.2 (5.08)
Anode
Gate
0.157 DIA
(4.0)
14.17(360.0)
Flat up
1.97
(50.0)
Dimensions
are in inches
(and millimeters).
Direction of Feed
TO-92 (3-lead) Ammo Pack (AP) Radial Leaded Specifications
Meets all EIA-468-C Standards
0.236
(6.0)
1.62
(41.2)
0.708
(18.0)
0.02 (0.5)
0.098 (2.5) MAX
1.27
(32.2)
0.354
(9.0)
0.1 (2.54)
0.5
(12.7)
Anode
0.2 (5.08)
0.157
(4.0) DIA
Cathode
Gate
Flat down
f Feed
no
Directio
25 Devices per fold
1.85
(47.0)
12.2
(310.0)
1.85
(47.0)
13.3
(338.0)
© 2016 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 05/02/16
Dimensions
are in inches
(and millimeters).
Teccor® brand Thyristors
1 Amp Standard SCRs
Compak Embossed Carrier Reel Pack (RP) Specifications
Meets all EIA-481-1 Standards
0.157
(4.0)
0.47
(12.0)
Anode
0.36
(9.2)
8.0
0.315
(8.0)
Cathode
Gate
0.059 DIA
(1.5)
12.99
(330.0)
0.512 (13.0) Arbor
Hole Dia.
Cover tape
Dimensions
are in inches
(and millimeters).
0.49
(12.4)
Direction of Feed
Part Numbering System
S 6 01 E
DEVICE TYPE
S: SCR
Part Marking System
75
TO-92 (E Package)
S601E
Lead Form Dimensions
xx: Lead Form Option
®
VOLTAGE RATING
4: 400V
6: 600V
CURRENT RATING
01: 1A (TO-92)
N: 1A (Compak)
SENSITIVITY & TYPE
[blank]: 10 mA (TO-92)
1: 10 mA (Compak)
PACKAGE TYPE
E: TO-92 SCR
N: Compak
YMLXX
Compak (C Package)
S6N1
®
YMXXX
Date Code Marking
Date Code Marking
Y:Year Code
M: Month Code
L: Location Code
XX: Lot Serial Code
Y:Year Code
M: Month Code
XXX: Lot Trace Code
© 2016 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 05/02/16