OPT-155Bxxxx RoHS Compliant 1x9 SC Duplex Optical Transceiver For Fast Ethernet, ATM, SONET OC-3/SDH STM-1 Features z Full Compliance with the Optical Performance Requirements of the ATM 100Mbps and 100 Base-FX Version of IEEE 802.3u z Industry Standard 1x9 Footprint and Duplex SC Connector Interface z Single 5V (OPT-155B1xxxxx) or 3.3V (OPT-155B2xxxxx) Power Supply z PECL Differential Inputs and Outputs z PECL or TTL Receiver Signal Detect Indicator z RoHS Compliance z Wave Solder and Aqueous Wash Process Compatible Description The OPT-155Bxxxx series are 1x9 optical transceiver modules designed expressly for high-speed communication applications that require rates of up to 155Mbps. They are all compliant with the SONET/SDH standards. These PIN / Preamplifier combinations are coupled into a custom quantizer IC which provides the final pulse shaping for the logic output and the Signal Detect function. The data output is differential. The signal detect output is single-ended. The OPT-155Bxxxx transceivers are supplied in industry standard 1x9 SIP package style with duplex SC connector. The OPT-155Bxxxx transceivers can meet Class 1 eye safety products and effective distance depending on ITU-T G.957 standard or power penalty. Application z Single-mode Fiber Backbone Links z Fast Ethernet and ATM Compatible The transmitter sections utilize 1310nm Edge Emitting InGaAsP Laser Diode. This Laser Diode is packaged in the optical subassembly portion of the transmitter section. A custom silicon IC that converts differential PECL logical signals into an analog LD driving current drives it. z Single-mode Fiber Media Converter The receiver sections utilize InGaAs PIN photodiodes coupled into a custom silicon trans-impedance preamplifier IC. These are packaged in the optical subassembly portion of receiver. Performance z OPT-155BxJxx data link up to 15Km in 9/125μm Single Mode Fiber. z OPT-155BxMxx data link up to 40Km in 9/125μm Single Mode Fiber. 1 DELTA ELECTRONICS, INC. Apr., 2009 Rev. 0L www.deltaww.com OPT-155Bxxxx Absolute Maximum Ratings Parameter Storage Temperature Lead Soldering Temperature Lead Soldering Time Supply Voltage Symbol TS TSOLD tSOLD VCC Min. -40 Typ. 0 Max. 85 260 10 6 Unit ºC ºC Sec. V Note Recommended Operating Conditions Parameter Symbol Min. 100 0 4.75 Typ. 155.52 5 Max. 200 70 5.25 Data Rate Ambient Operating Temperature TA Supply Voltage VCC 3.15 3.3 3.45 Symbol Min. Typ. VIL - VCC VIH - VCC VOL - VCC VOH - VCC VSDL - VCC VSDH - VCC Unit Mbps ºC V Note Note1 OPT-155B1xxx OPT-155B2xxx OPT-155B4xxx Note1: See “Order Information” for detail Electrical Characteristics Parameter Transmitter Transmitter Data Input Voltage-Low Transmitter Data Input Voltage-High Receiver Data Output Voltage-Low Data Output Voltage-High SD Output Voltage-Low SD Output Voltage-High SD Output Voltage-Low SD Output Voltage-High VSDL VSDH Max. Unit -1.81 -1.16 -1.48 -0.88 V V -1.95 -1.045 -1.95 -1.045 0 2 -1.62 -0.74 -1.62 -0.74 0.8 VCC V V V V V V Note PECL LVTTL Optical Characteristics (Data Rate = 155.52Mbps, PRBS=223-1, NRZ, 9/125μm SMF) Parameter Symbol Min. Typ. Max. Unit Note Transmitter Supply Current ICC mA 165 -15 -8 OPT-155BxJxx Mean Launch Power P0 dBm -5 0 OPT-155BxMxx 8.2 OPT-155BxJxx Optical Extinction Ratio ER dB 10 OPT-155BxMxx Center Wavelength λC 1270 1310 1360 nm 7.7 OPT-155BxJxx Spectral Width (RMS) σ nm 3 OPT-155BxMxx Output Eye Diagram Compliant with ITU-T recommendation G.957 Receiver Supply Current ICC 145 mA -31 OPT-155BxJxx Note1 Sensitivity PIN dBm -34 OPT-155BxMxx Note1 -31 OPT-155BxJxx PA dBm Signal Detect-Asserted -34 OPT-155BxMxx PD -45 dBm Signal Detect-DeAsserted 2 Apr., 2009 Rev. 0L DELTA ELECTRONICS, INC. www.deltaww.com OPT-155Bxxxx PA - PD 0.5 dB Signal Detect-Hysteresis Receiver Saturation Power PSAT -8 dBm Note1: The sensitivity should be tested at a BER of 1×10-10 or better with an input signal consisting of 155Mbps, 223-1 PRBS and ER=9dB. Mask of the eye diagram for the optical transmit signal Pin Definition Pin No. 1 2 3 4 5 6 7 8 9 Pin Name GND RD(+) RD(-) SD VccR VccT TD(-) TD(+) GND Description Receiver Signal Ground Receiver Data Out Non-inverted (PECL) Receiver Data Out Inverted (PECL) Receiver Signal Detect (PECL or TTL) Receiver Power Supply Transmitter Power Supply Transmitter Data In Inverted (PECL) Transmitter Data In Non-inverted (PECL) Transmitter Signal Ground Pin Out Drawing 3 DELTA ELECTRONICS, INC. Apr., 2009 Rev. 0L www.deltaww.com OPT-155Bxxxx Recommended Circuit Schematic R1=R3=82 ohm (3.3V),68 ohm(5V) R2=R4=130 ohm (3.3V),191 ohm (5V) R5=R6=150 ohm (3.3V),270 ohm (5V) R7=130 ohm (3.3V PECL),82 ohm(5V),NC (TTL) R8=82 ohm (3.3V PECL),130 ohm(5V),NC (TTL) C1=C2=C3=C4=C5=C6=C7=100 nF C8=C9=10uF L1=L2=1uH 4 DELTA ELECTRONICS, INC. Apr., 2009 Rev. 0L www.deltaww.com OPT-155Bxxxx Package Outline Drawing 5 DELTA ELECTRONICS, INC. Apr., 2009 Rev. 0L www.deltaww.com OPT-155Bxxxx Regulatory Compliance Feature Electromagnetic Interference (EMI) Radio Frequency Electromagnetic Field Electrostatic Discharge to the Duplex Receptacle Electrostatic Discharge to the Electrical Pins Eye Safety Component Recognition Reference FCC Class B EN 55022 Class B (CISPR 22A) EN 61000-4-3 IEC 1000-4-3 EN 61000-4-2 IEC 1000-4-2 IEC 801.2 Performance (1) Satisfied with electrical characteristics of product spec. (2) No physical damage MIL-STD-883E Method 3015.7 US FDA CDRH AEL Class 1 EN 60950: 2000 EN 60825-1: 1994+A11+A2 EN 60825-2: 2000 Underwriters Laboratories and Canadian Standards Association Joint Component Recognition for Information Technology Equipment Including Electrical Business Equipment CDRH File # 0321539-00 TUV Certificate No. R50032471 UL File # E239394 Order information OPT- 155BX1X2X3X4X5X6 X1 Power Supply Voltage and SD Level X4 1: 5.0V, PECL SD Level 2: 3.3V, PECL SD Level 4: 3.3V, TTL SD Level X2 R: RoHS Compliant Distance X5 J: 15km M: 40km X3 RoHS Performance Blank: Old Design A: New Design E: OPT without EMI Shielding Plastic Housing Data Coupling X6 1: 1x9 SC DC/DC Temperature Blank: 0 to +70 degree C H: -10 to + 85 degree C T: -40 to + 85 degree C Appendix A. Document Revision Version No. 0G Date 2006-11 2008-01 0H 0I 0J 0K 2008-04 2008-12 2009-02 0L 2009-04 Description Release Update “Recommended Circuit Schematic”; Correct SD Output Voltage, Pin Definition, Package Outline, Order Information. Update “E” definition of “OPT-155B2J1RET”. Update Outline Package Instruction. Update label change. Revise Document Style; Cut off OPT-155BxHxx PNs, OPT-155BxLxx PNs, Non-RoHS PNs; Revise Parameter symbols; Revise Pin Out Drawing. 6 DELTA ELECTRONICS, INC. Apr., 2009 Rev. 0L www.deltaww.com