LCP-10G3B4HDRT-G

LCP-10G3B4HDR(T)-G
10GBASE-LR Lite SFP+ Optical Transceiver
FEATURES
RoHS compliance
Compliant with SFP transceiver SFF-8472
MSA specification
1310nm FP laser
Built-in digital diagnostic monitoring function
Compliant with Industry Standard RFT
Electrical Connector and Cage
Duplex LC duplex fiber-optics connector
Laser Class 1 Product which comply with the
requirements of EN 60825
Description
Applications
The LCP-10G3B4HDR(T)-G is hot pluggable
3.3V
Small-Form-Factor
designed
for
transceiver
high-speed
modules
communication
The LCP-10G3B4HDR(T)-G is designed to be
with
SFF-8472
Agreement
(MSA)
monitoring
functions:
with
SFP
SAN applications
Multi-source
digital
10G Ethernet switch/router
10G Fiber channel
applications that require rates up to 6.144Gbps.
compliant
10G LAN switch
diagnostic
Performance
VCC,
LCP-10G3B4HDR(T)-G: Link distance up to 2km
Temperature,
TX
over 9um SMF
optical power, TX laser bias current, and RX
received optical power.
The
post-amplifier
of
the
LCP-10G3B4HDR(T)-G also includes a Loss of
Signal (LOS) circuit that provides a TTL logic-high
output when the received optical level is below a
preset LOS Assert threshold.
1
DELTA ELECTRONICS, INC.
Revision: S2
2013/05/31
www.deltaww.com
LCP-10G3B4HDR(T)-G
Absolute Maximum Ratings
Parameter
Storage Temperature
Supply Voltage Range @3.3V
Symbol
TS
VCC3
Min.
-40
-0.5
Typ.
Max.
85
3.6
Unit
℃
V
Min.
Typ.
Max.
Unit
+70
+85
+85
3.465
85
℃
Recommended Operating Conditions
Parameter
Case Operating Temperature
LCP-10G3B4HDR-G
LCP-10G3B4HDRH-G
LCP-10G3B4HDRT-G
Supply Voltage @3.3V
Relative Humidity (non condensation)
Symbol
-5
-10
-40
3.135
5
TC
VCC3
-
3.30
Note
V
%
Electrical Characteristics
(VCC=3.135V to 3.465V)
Parameter
Total Supply Current
Transmitter
Transmitter Differential Input Voltage
Transmitter Disable Input-High
Transmitter Disable Input-Low
Transmitter Fault Pull up Resistor
Transmitter Fault Output-High
Transmitter Fault Output-Low
Receiver
Receiver Differential Output Voltage
Receiver LOS Load
LOS Output Voltage-Low
LOS Output Voltage-High
Notes:
Symbol
ICC
Min.
Vin,pp
VDISH
VDISL
RTX_FAULT
VTXFH
VTXFL
0.3
2
0
4.7
2
0
Vout,pp
RRXLOS
VLOSH
VLOSL
0.4
4.7
2
0
Typ.
0.7
Max.
300
Unit
mA
Note
1
VCC+0.3
0.8
10
VCC+0.3
0.8
V
V
V
kΩ
V
V
1
1
10
VCC+0.3
0.8
V
kΩ
V
V
2
3
2
1.
Internally AC coupled and terminated to 100 Ohm differential load.
2.
Pull up to VCC on host Board.
3.
Internally AC coupled, but requires a 100 Ohm differential termination at or internal to Serializer/ Deserializer.
Optical Transmitter Characteristics
Parameter
Signaling speed (nominal)
Symbol
Min
R
λ
OMA
σ
AP
ER
1260
300
Units
Notes
Gb/s
±100
ppm
nm
uW
4
nm
-8.4
+0.5
dBm
3.5
dB
{0.25, 0.40, 0.45, 0.25, 0.28, 0.40}
2
DELTA ELECTRONICS, INC.
Max
10.3125
Signaling speed variation from nominal
Center Wavelength
Optical Modulaion Amplitude
Spectral Width (RMS)
Average output power
Extinction Ratio
Transmitter eye mask
Typ
1360
Revision: S2
2013/05/31
www.deltaww.com
LCP-10G3B4HDR(T)-G
Output Eye Mask
4. Optical Receiver Characteristics
Parameter
Signaling speed (nominal)
Signaling speed variation from
nominal
Overload
Sensitivity in OMA
Wavelength
LOS De-assert
LOS Assert
Return Loss
LOS Hysteresis
Symbol
Min
Ts
Typ
Max
10.3125
PO
RSO
λ
LOSD
LOSA
1260
-30
12
0.5
Units
Notes
Gb/s
±100
ppm
0
-12.6
1355
-16
dBm
dBm
nm
dBm
dBm
dB
dB
[1]
Notes:
1.
Measured with 2^31-1 PRBS for BER = 10-12. Per IEEE802.3ae
3
DELTA ELECTRONICS, INC.
Revision: S2
2013/05/31
www.deltaww.com
LCP-10G3B4HDR(T)-G
SFP+ Transceiver Electrical Pad Layout
Module Electrical Pin Definition
Pin
Logic
Symbol
2
LVTTL-O
TX_Fault
3
LVTTL-I
TX_Disable
4
LVTTL-I/O
SDA
2- write Serial Interface Data Line
5
LVTTL-I/O
SCL
2- write Serial Interface Clock
1
VeeT
6
MOD_ABS
7
LVTTL-I
RS0
8
LVTTL-O
RX_LOS
9
LVTTL-I
Name/Description
Note
Module Transmitter Ground
1
Module Transmitter Fault
2
Transmitter Disable; Turns off transmitter laser output
3
Module Absent, connected to VeeT or VeeR in the module
4
Not Implement
Receiver Loss of Signal Indication
2
RS1
Not Implement
10
VeeR
Module Receiver Ground
1
11
VeeR
Module Receiver Ground
1
12
CML-O
RD-
Receiver Inverted Data Output
13
CML-O
RD+
Receiver Non-Inverter Data Output
14
VeeR
Module Receiver Ground
15
VccR
Module Receiver 3.3V Supply
16
VccT
Module Transmitter 3.3V Supply
17
VeeT
Module Transmitter Ground
18
CML-I
TD+
Transmitter Non-Inverted Data Input
19
CML-I
TD-
Transmitter Inverted Data Input
20
VeeT
Module Transmitter Griund
4
DELTA ELECTRONICS, INC.
1
1
1
Revision: S2
2013/05/31
www.deltaww.com
LCP-10G3B4HDR(T)-G
Note:
1. The module signal ground pins, VeeR and VeeT, shall be isolated from the module case.
2. This pin is an open collector/drain output pin and shall be pulled up with 4.7k-10k ohms to Host_Vcc
on the host board. Pull ups can be connected to multiple power supplies, however the host board
design shall ensure that no module pin has voltage exceeding module VccT/R + 0.5V.
3. This pin is an open collector/drain input pin and shall be pulled up with 4.7k-10k ohms to VccT in the
Module.
4. This pin shall be pulled up with 4.7k-10k ohms to Host_Vcc on the host board.
Low speed electrical control pins and 2-wire interface
In addition to the 2-wire serial interface, the SFP+ module has the following low speed pins for control and
status:
‧ TX_Fault
‧ TX_Disable
‧ RS0/RS1
‧ MOD_ABS
‧ RX_LOS
1 TX_Fault
TX_Fault is a module output pin that when High, indicates that the module transmitter has detected a fault
condition related to laser operation or safety.
The TX_Fault output pin is an open drain/collector and must be pulled p to the Host_Vcc with 4.7k-10k
ohms on the host board
2 TX_Disable
TX_Disable is a module input pin. When TX_Disable is asserted High or Left open, the SFP+ module
transmitter output must be turned off. The TX_DIS pin must be pulled up to VccT in the SFP+ module..
3 RS0/RS1
RS0 and RS1 are module input rate select pins and are pulled low to VeeT with a > 30kΩ resistor in the
module. RS0 is an input hardware pin which optionally selects the optical receive data path rate coverage
for an SFP+ module. RS1 is an input hardware pin which optionally selects the optical transmit path data
rate coverage for an SFP+ module.
4 MOD_ABS
Mod_ABS is pulled up to Host_Vcc with 4.7k-10k ohms on the host board and connected to VeeT or VeeR
in the SFP+ module. MOD_ABS is then asserted “High” when the SFP+ module is physically absent from
a host slot. In the SFP MSA (INF8074i) this pin had the same function but is called MOD_DEF0.
5
DELTA ELECTRONICS, INC.
Revision: S2
2013/05/31
www.deltaww.com
LCP-10G3B4HDR(T)-G
5 SCL/SDA
SCL is the 2-wire interface clock and SDA is the 2-wire interface data line. SCL and SDA are pulled up to
a voltage in the range of 3.14V to 3.46V on the host.
6 RX_LOS
RX_LOS when High indicated an optical signal level below that specified in the relevant standard. The
RX_LOS pin is an open drain/collector output and must be pulled up to host Vcc with a 4.7k-10k ohms on
the host board.RX_LOS assert min and de-assert max are defined in the relevant standard. To avoid
spurious transition of RX_LOS a minimum hysteresis of 0.5 dB is recommended.
Recommend Circuit Schematic
6
DELTA ELECTRONICS, INC.
Revision: S2
2013/05/31
www.deltaww.com
LCP-10G3B4HDR(T)-G
13.55±0.15
13.75±0.25
Package Outline Drawing for Metal Housing with Bail de-latch
1.4±0.5
8.5±0.15
9.35(ref)
6.25±0.05
Product Label
1.5 (ref)
2.1 Max
See Note.2
10 Max
47.5±0.2
+0.15
9.2±0.1
Notes :
1. Units : mm
2. Handle Color : Blue
13.1
2.50 -0.05
Safety Label
Product Label
Safety Label
27.00
LOGO(BLUE)
LCP-10G3B4HDRT-G
11.50
LC
Receptacle
Class 1 Laser Product
Complies with 21 CFR
1040.10 and 1040.11
Made in China
XXXXXXXXXXXXXX
R1
.0
0
1310 nm TX / RX 1310 nm
7
DELTA ELECTRONICS, INC.
Revision: S2
2013/05/31
www.deltaww.com
LCP-10G3B4HDR(T)-G
Timing parameters for SFP+ management
Parameter
Symbol
TX_DISABLE Assert time
t_off
TX_DISABLE Negate time
t_on
Time to initialize 2-wire
t_2w_start_up
interfase
Time to initialize
t_start_up
Time to initialize cooled
t_start_up_cooled
module
Time to Power Up to Level 2
t_power_level2
Time to Power Down from
T_power_down
Level 2
TX_Fault assert
TX_Fault_on
TX_Fault assert for cooled
TX_Fault_on
module
TX_Fault Reset
t_reset
RS0, RS1 rate select timing
t_RS0_FC,
for FC
RS1_FC
RS0, RS1 rate select timing
t_RS0, t_RS1
non FC
RX_LOS assert delay
t_los_on
RX_LOS negate delay
t_los_off
Min.
Max.
100
2
Unit
µsec
msec
Note
1
2
300
msec
3
300
msec
4
90
sec
4
300
msec
5
300
msec
6
1
msec
7
50
msec
7
µsec
8
500
µsec
9
10
msec
9
100
100
µsec
µsec
10
11
10
Notes:
1)
Rising edge of TX_Disable to fall of output signal below 10% of nominal.
2)
Falling edge of TX_Disable to rise of output signal above 90% of nominal. This only applies in normal
operation, not during start up or fault recovery.
3)
From power on or negation of TX_Disable.
4)
From power on or TX_Disable negated during power up, or TX_Fault recovery, until non-cooled power
level 1 part (or non-cooled power level 2 part already enabled at power level 2 for TX_Fault recovery)
is fully operational.
5) From falling edge of stop bit enabling power level 2 until non-cooled module is fully operational.
6) From falling edge of stop bit disabling power level 2 until module is within power level 1 requirements.
7) From Occurrence of fault to assertion of TX_Fault.
8) Time TX_Disable must be held High to reset TX_Fault.
9) From assertion till stable output.
10) From Occurrence of loss of signal to assertion of LOS
11) From Occurrence of presence of signal to negation of RX_LOS.
8
DELTA ELECTRONICS, INC.
Revision: S2
2013/05/31
www.deltaww.com
LCP-10G3B4HDR(T)-G
Enhanced Digital Diagnostic Interface
The memory map in the following describes an extension to the memory map defined in SFP MSA. The enhanced
interface uses the two wire serial bus address 1010001X (A2h) to provide diagnostic information about the module’s
present operating conditions.
2 wire address 1010000 X (A0h)
2 wire address 1010001 X (A2h)
0
0
Alarm and Warning Thresholds
(56 bytes)
55
Serial ID Defined by SFP MSA
(96 bytes)
56
Cal Constants
(40 bytes)
95
96
95
96
Real Time Diagnostic Interface
(24 bytes)
119
Vender Specific
(32 bytes)
120
Vender Specific
127
127
128
128
User Writable EEPROM
(120 bytes)
247
Reserved in SFP MSA
(128 bytes)
248
255
255
Vender Specific
(8 bytes)
Digital Diagnostic Memory Map Specific Data Field Descriptions
9
DELTA ELECTRONICS, INC.
Revision: S2
2013/05/31
www.deltaww.com
LCP-10G3B4HDR(T)-G
EEPROM Serial ID Memory Contents (2-Wire Address A0h)
Address
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
Hex
03
04
07
00
00
00
00
00
00
00
00
03
67
00
02
14
00
00
00
00
44
45
4C
54
41
20
20
20
20
20
20
20
20
20
20
20
00
00
00
00
4C
43
50
ASCII
D
E
L
T
A
L
C
P
Address
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
Hex
2D
31
30
47
33
42
34
48
44
52
2D
47
20
41
00
00
00
05
1E
00
CS1
00
1A
00
00
SN
SN
SN
SN
SN
SN
SN
SN
SN
SN
SN
SN
SN
SN
SN
SN
DC
DC
ASCII
1
0
G
3
B
4
H
D
R
G
Note 1
Note 2
Note 3
Note 4
Address
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
Hex
DC
DC
DC
DC
DC
DC
68
F0
05
CS2
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
ASCII
Note 5
Note 6
Notes:
1)
Byte 40-55: Part number
2)
Byte 63: Check sum of bytes 0-62.
3)
Byte 68-83: Serial number.
4)
Byte 84-91: Date code.
5)
Byte 95: Check sum of bytes 64-94.
6)
Byte 128 to 255 had been set hex 00.
10
DELTA ELECTRONICS, INC.
Revision: S2
2013/05/31
www.deltaww.com
LCP-10G3B4HDR(T)-G
Digital Diagnostic Monitoring Interface
Alarm and Warning Thresholds (2-Wire Address A2h)
Address
#
Bytes
00-01
02-03
04-05
06-07
08-09
10-11
12-13
14-15
16-17
18-19
20-21
22-23
24-25
26-27
28-29
30-31
32-33
34-35
36-37
38-39
40-45
56-91
92-94
95
96-97
98-99
100-101
102-103
104-105
106-109
110
111
112-119
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
16
36
3
1
2
2
2
2
2
4
1
1
8
Name
Temp High Alarm
Temp Low Alarm
Temp High Warning
Temp Low Warning
Voltage High Alarm
Voltage Low Alarm
Voltage High Warning
Voltage Low Warning
Bias High Alarm
Bias Low Alarm
Bias High Warning
Bias Low Warning
TX Power High Alarm
TX Power Low Alarm
TX Power High Warning
TX Power Low Warning
RX Power High Alarm
RX Power Low Alarm
RX Power High Warning
RX Power Low Warning
Reversed
External Calibration Constants
Reversed
Checksum
Real Time Temperature
Real Time Supply Voltage
Real Time Tx Bias Current
Real Time Tx Optical Power
Real Time Rx Received Power
Reserved
Optional Status/ Control Bits
Reserved
Optional Set of Alarm and Warning
Value (Dec.)
Unit
Note
Tc(Max.)+8
Tc(Min.)-8
Tc(Max.)+3
Tc(Min.)-3
3.8
2.8
3.5
3.1
IOP*2+35
IOP–25
IOP *2+30
IOP –20
2.5
-10.4
1.5
-9.4
2
-14.6
1
-13.6
℃
1
Volt
mA
2
dBm
dBm
3
4
5
Notes:
1)
TC: Case Operating temperature
2)
IOP: Operating current at room temperature. The min. setting current is 0 mA.
3)
Byte 95 contains the low order 8bits of sum of bytes 0~94
11
DELTA ELECTRONICS, INC.
Revision: S2
2013/05/31
www.deltaww.com
LCP-10G3B4HDR(T)-G
4)
State/ Control Bits
Byte
110
110
110
110
110
110
110
110
Bit
7
6
5
4
3
2
1
0
Name
Tx Disable State
Soft Tx Disable
Reserved
Rate Select State
Soft Rate Select
Tx Fault
LOS
Data_Ready_Bar
Description
Digital state of the Tx disable input pin
Read/ Write bit that allow software disable of laser
Rate Select State
Software Rate Select State
Digital state of the Tx fault output pin
Digital state of the LOS output pin.
NA
5.)
Optional Set of Alarm and Warning
Byte
112
112
112
112
112
112
112
112
113
113
113
116
116
116
116
116
116
116
116
117
117
117
Bit
7
6
5
4
3
2
1
0
7
6
5-0
7
6
5
4
3
2
1
0
7
6
5-0
Name
Temp High Alarm
Temp Low Alarm
Vcc High Alarm
Vcc Low Alarm
Tx Bias High Alarm
Tx Bias Low Alarm
Tx Power High Alarm
Tx Power Low Alarm
Rx Power High Alarm
Rx Power Low Alarm
Reserved
Temp High Warning
Temp Low Warning
Vcc High Warning
Vcc Low Warning
Tx Bias High Warning
Tx Bias Low Warning
Tx Power High Warning
Tx Power Low Warning
Rx Power High Warning
Rx Power Low Warning
Reserved
Description
Set when internal temperature exceeds high alarm level
Set when internal temperature is below low alarm level
Set when internal supply voltage exceeds high alarm level
Set when internal supply voltage is below low alarm level
Set when Tx Bias current exceeds high alarm level
Set when Tx Bias current is below low alarm level
Set when Tx output power exceeds high alarm level
Set when Tx output power is below low alarm level
Set when received power exceeds high alarm level
Set when received power is below low alarm level
Set when internal temperature exceeds high warning level
Set when internal temperature is below low warning level
Set when internal supply voltage exceeds high warning level
Set when internal supply voltage is below low warning level
Set when Tx Bias current exceeds high warning level
Set when Tx Bias current is below low warning level
Set when Tx output power exceeds high warning level
Set when Tx output power is below low warning level
Set when received power exceeds high warning level
Set when received power is below low warning level
Digital Diagnostic Monitor Accuracy
Parameter
Transceiver Temperature
Power Supply Voltage
TX Bias Current
TX Optical Power
RX Optical Power
Typical Value
± 5℃
±3%
± 10%
± 3dB
± 3dB
Note
1
Notes:
1) Voltage is measured internal to the transceiver
12
DELTA ELECTRONICS, INC.
Revision: S2
2013/05/31
www.deltaww.com
LCP-10G3B4HDR(T)-G
Regulatory Compliance
Feature
Reference
Electromagnetic Interference (EMI)
FCC Part15 Class B
Electrostatic Discharge (ESD)
IEC/EN 61000-4-2
MIL-STD-883E
EIA-JESD22-A115-A
IEC 60825-1:2001
EN 60825
Laser Eye Safety
IEC/EN 60950-1
UL60950
Component Recognition
Ordering Information for SFP modules
LCP-10G3B4HDRX1-G
X1: Temperature
Blank: -5 to +70 degree C
H: -10 to +85 degree C
T: -40 to +85 degree C
Appendix A. Document Revision
Version No.
Date
Description
S0
2012-11-20
First released
S1
2013-05-16
P9: Modified the shielding design.
S2
2013-05-31
P9: Changed the mechanical design.
13
DELTA ELECTRONICS, INC.
Revision: S2
2013/05/31
www.deltaww.com