CF5011 series 1.8V Crystal Oscillator Module ICs OVERVIEW The CF5011 series are low-voltage crystal oscillator module ICs that operate at 1.8V. The crystal oscillator circuit and output buffer employ a low-voltage CMOS process operating at 1.8V. The crystal oscillator circuit has a built-in thin-film feedback resistor with good temperature characteristics and built-in capacitors with excellent frequency response, making possible a stable 3rd overtone oscillator with only the addition of a crystal element. FEATURES ■ ■ ■ ■ ■ 3rd overtone oscillation 1.6 to 2.0V operating supply voltage range 30MHz to 70MHz recommended operating frequency range Inverter amplifier feedback resistor built-in Oscillator capacitors CG , CD built-in ■ ■ ■ ■ ■ Standby function fO output frequency (oscillator frequency) 8mA output drive capability (VDD = 1.6V) CMOS output duty level Chip form (CF5011×××) SERIES CONFIGURATION Built-in capacitance [pF] Recommended operating frequency range1 [MHz] gm ratio CF5011ALA 30 to 40 CF5011ALB Rf [kΩ] Standby function 16 4.0 Yes 8 16 3.9 Yes 1.0 8 16 2.2 Yes 60 to 70 1.5 8 16 2.7 Yes CF5011ANA 30 to 40 1.0 14 16 4.0 No CF5011ANB 40 to 50 1.0 8 16 3.9 No CF5011ANC 50 to 60 1.0 8 16 2.2 No CF5011AND 60 to 70 1.5 8 16 2.7 No Version CG CD 1.0 14 40 to 50 1.0 CF5011ALC 50 to 60 CF5011ALD 1. The recommended operating frequency is a yardstick value derived from the crystal used for NPC characteristics authentication. However, the oscillator frequency band is not guaranteed. Specifically, the characteristics can vary greatly due to crystal characteristics and mounting conditions, so the oscillation characteristics of components must be carefully evaluated. ORDERING INFORMATION Device Package CF5011×××–1 Chip form SEIKO NPC CORPORATION —1 CF5011 series PAD LAYOUT (Unit: µm) VDD (920,1310) HA5011A Y Q (0,0) INHN XTN XT VSS X Chip size: 0.92 × 1.31mm Chip thickness: 300 ± 30µm Chip base: VDD level PIN DESCRIPTION and PAD DIMENSIONS Pad dimensions [µm] Name I/O Description X Y 195 212 385 212 575 212 INHN I Operation mode control input. <CF5011AL×> The oscillator stops and Q becomes high impedance when LOW. Power-saving pull-up resistor built in <CF5011AN×> Q becomes high impedance when LOW. Pull-up resistor built in XT I Amplifier input XTN O Amplifier output VSS – Ground 766 212 Q O Output. Output frequency (fO). High impedance when INHN is LOW 765 1152 VDD – Supply voltage 162 1152 Crystal oscillator connection pins. Crystal oscillator connected between XT and XTN BLOCK DIAGRAM CF5011AL× CF5011AN× VDD VSS VDD VSS XTN XTN CG Rf 1 Cf CD CG Rf 1 XT CD Rf 2 Cf Q XT Q Rf 2 INHN INHN Substrate potential: VDD Substrate potential: VDD SEIKO NPC CORPORATION —2 CF5011 series SPECIFICATIONS Absolute Maximum Ratings VSS = 0V Parameter Symbol Condition Rating Unit Supply voltage range VDD −0.5 to +3.6 V Input voltage range VIN −0.5 to VDD + 0.5 V Output voltage range VOUT −0.5 to VDD + 0.5 V Operating temperature range Topr −40 to +85 °C Storage temperature range Tstg −65 to +150 °C Output current IOUT 25 mA Recommended Operating Conditions VSS = 0V, f ≤ 70MHz, CL = 15pF unless otherwise noted. Parameter Symbol Condition Rating min typ max Unit Supply voltage VDD 1.6 – 2.0 V Input voltage VIN VSS – VDD V TOPR −20 – +80 °C Operating temperature Electrical Characteristics VDD = 1.6 to 2.0V, VSS = 0V, Ta = −20 to +80°C unless otherwise noted. Parameter Symbol HIGH-level output voltage VOH LOW-level output voltage VOL Rating Condition Unit min typ max Q: Measurement cct 1, VDD = 1.6V, IOH = 8mA 1.1 1.3 – Q: Measurement cct 2, VDD = 1.6V, IOL = 8mA – 0.3 0.4 V – – 10 µA VOH = VDD V Output leakage current IZ Q: Measurement cct 2, INHN = LOW, VDD = 2.0V – – 10 µA HIGH-level input voltage VIH INHN 0.7VDD – – V LOW-level input voltage VIL INHN – – 0.3VDD V Current consumption IDD Measurement cct 3, load cct 1, INHN = open, CL = 15pF, f = 70MHz – 9 18 mA Standby current IST Measurement cct 3, INHN = LOW CF5011AL× – – 100 µA RUP1 Measurement cct 4, INHN = LOW CF5011AL× 0.4 – 8 MΩ Measurement cct 4, INHN = 0.7VDD CF5011AL× CF5011AN× 50 – 150 kΩ CF5011ALA, ANA 3.20 4.0 4.80 kΩ CF5011ALB, ANB 3.12 3.9 4.68 kΩ CF5011ALC, ANC 1.76 2.2 2.64 kΩ CF5011ALD, AND 2.16 2.7 3.24 kΩ 50 – 150 kΩ INHN pull-up resistance RUP2 VOL = VSS AC feedback resistance Rf1 Design value. A monitor pattern on a wafer is tested. DC feedback resistance Rf2 Measurement cct 5 AC feedback capacitance Cf Design value. A monitor pattern on a wafer is tested. CG Design value. A monitor pattern on a wafer is tested. CD Design value. A monitor pattern on a wafer is tested. Built-in capacitance 9.3 10 10.7 pF CF5011ALA, ANA 13.02 14 14.98 pF CF5011ALB, ALC, ALD CF5011ANB, ANC, AND 7.44 8 8.56 pF CF5011ALA, ANA 14.88 16 17.12 pF CF5011ALB, ALC, ALD CF5011ANB, ANC, AND 14.88 16 17.12 pF SEIKO NPC CORPORATION —3 CF5011 series Switching Characteristics VDD = 1.6 to 2.0V, VSS = 0V, Ta = −20 to +80°C unless otherwise noted. Rating Parameter Symbol Condition Unit min typ max Output rise time tr Measurement cct 3, load cct 1, 0.2VDD to 0.8VDD , CL = 15pF – 1 3.5 ns Output fall time tf Measurement cct 3, load cct 1, 0.8VDD to 0.2VDD , CL = 15pF – 1 3.5 ns Measurement cct 3, load cct 1, Ta = 25°C, VDD = 1.8V, CL = 15pF, f ≤ 70MHz 40 – 60 % – – 100 ns – – 100 ns Output duty cycle1 Duty Output disable delay time2 tPLZ 2 tPZL Output enable delay time Measurement cct 3, load cct 1, Ta = 25°C, VDD = 1.6V, CL ≤ 15pF 1. The duty cycle characteristic is checked the sample chips of each production lot. 2. In the case of the CF5011AL×, oscillator stop function is built-in. When INHN goes LOW, normal output stops. When INHN goes HIGH, normal output is not resumed until after the oscillator start-up time has elapsed. Current consumption and Output waveform with NPC’s standard crystal f [MHz] R [Ω] L [mH] Ca [fF] Cb [pF] 30 18.62 16.24 1.733 5.337 40 20.53 11.34 1.396 3.989 50 22.17 7.40 1.370 4.105 60 15.37 3.83 1.836 5.191 70 25.42 4.18 1.254 5.170 Cb L Ca R FUNCTIONAL DESCRIPTION Standby Function Output three-state function (CF5011AL×, CF5011AN×) When INHN goes LOW, the oscillator output on Q goes high impedance. Oscillator stop function (CF5011AL×) When INHN goes LOW, the oscillator stops. Version INHN Q Oscillator HIGH (or open) fO output frequency Normal operation LOW High impedance Stop HIGH (or open) fO output frequency Normal operation LOW High impedance Normal operation CF5011AL× CF5011AN× SEIKO NPC CORPORATION —4 CF5011 series MEASUREMENT CIRCUITS Measurement cct 1 Measurement cct 4 C1 Signal Generator VDD XT XTN INHN R1 VSS Q output Q XTN INHN VSS VOH V 0V VPR IPR VDD IPR (VPR = V SS) RUP2 = VDD VPR IPR (V PR = 0.7V DD) A Measurement cct 5 IOL, IZ VDD VDD XT IZ XT Rf2 = A Q XTN INHN RUP1 = X'tal R2 1.0VP−P , 10MHz sine wave input signal C1 : 0.001µF R1 : 50Ω R2 : 137.5Ω Measurement cct 2 VDD XT Q VSS XTN INHN V VOL VDD IRf VSS A IRf Measurement cct 3 Load cct 1 IDD A XT Q output VDD X'tal CL (Including probe capacitance) Q XTN INHN VSS CL = 15pF SEIKO NPC CORPORATION —5 CF5011 series Switching Time Measurement Waveform tr , tf , Duty Q output 0.8V DD 0.8V DD 0.2V DD 0.2V DD DUTY measurement voltage (0.5V DD ) TW tr tf Output duty cycle DUTY measurement voltage (0.5V DD) Q output TW DUTY= TW/ T T 100 (%) Output Enable/Disable Delay The following figure shows the oscillator timing during normal operation (CF5011AN× only). In case of CF5011AL×, the oscillator stops when the device is in standby. When standby is released, the oscillator starts and stable oscillator output occurs after a short delay. INHN VIH VIL tPZL tPLZ Q output INHN input waveform tr = tf 10ns SEIKO NPC CORPORATION —6 CF5011 series Please pay your attention to the following points at time of using the products shown in this document. The products shown in this document (hereinafter “Products”) are not intended to be used for the apparatus that exerts harmful influence on human lives due to the defects, failure or malfunction of the Products. Customers are requested to obtain prior written agreement for such use from SEIKO NPC CORPORATION (hereinafter “NPC”). Customers shall be solely responsible for, and indemnify and hold NPC free and harmless from, any and all claims, damages, losses, expenses or lawsuits, due to such use without such agreement. NPC reserves the right to change the specifications of the Products in order to improve the characteristic or reliability thereof. NPC makes no claim or warranty that the contents described in this document dose not infringe any intellectual property right or other similar right owned by third parties. Therefore, NPC shall not be responsible for such problems, even if the use is in accordance with the descriptions provided in this document. Any descriptions including applications, circuits, and the parameters of the Products in this document are for reference to use the Products, and shall not be guaranteed free from defect, inapplicability to the design for the mass-production products without further testing or modification. Customers are requested not to export or re-export, directly or indirectly, the Products to any country or any entity not in compliance with or in violation of the national export administration laws, treaties, orders and regulations. Customers are requested appropriately take steps to obtain required permissions or approvals from appropriate government agencies. SEIKO NPC CORPORATION 1-9-9, Hatchobori, Chuo-ku, Tokyo 104-0032, Japan Telephone: +81-3-5541-6501 Facsimile: +81-3-5541-6510 http://www.npc.co.jp/ Email: [email protected] NC0110CE 2006.04 SEIKO NPC CORPORATION —7