Hall Effect Sensors Flange Mount > 55140 55140 Miniature Flange Mounting Sensor Description The 55140 is a small flange mounting hall effect sensor occupying only 3.22cm² (0.500”² ) board space with a choice of digital, or programmable analogue outputs. It is available as three-wire (voltage output) or two-wire (current output) versions. It’s case design enables screw or adhesive mounting and capable of switching up to 28Vdc and 20mA. It comes with a range of sensitivity, cable length and connector options. Features • Magnetically operated position sensor • Digital,latching or programmable analog types available • Medium, high or programmable sensitivities • Three-wire (voltage output) or twowire (current output) versions Block Diagram Two-wire Version VDD Pin 1 (Red) Cn Hall Plate Switch Current Source Comparator Benefits Clock GND Pin 2 (Black) 1. Add capacitor Cn as shown, close for the sensors for transient suppression if required. • High switching speed up to 10kHz • Long life; up to 20 billion operations • Operates in static or dynamic magnetic field 2. Add pull-up resistor Rpu as shown for sinking output. The Rpu value should be calculated using your supply voltage while keeping the ON state current at a level below the maximum. Rpu = VDD/Io; Applications Notes: Rpu = 12Vdc/10mA = 1.2 Three-wire Version VDD Pin 1 (Red) Cn VDD Hall Plate Switch Comparator Output Clock GND Pin 2 (Black) • Vibration 50g max. @ 50-2,000Hz • Shock 150g max. @ 11ms ½ Sine • EMC to DIN 40839 (Consult Littelfuse) • Reverse/Over voltage protection • Built in temperature compensation • Open Drain Output • Unaffected by harsh environment • Customer selection of cable length and connector type • Flow metering • Angle sensing • Magnetic encoders • Position and limit sensing • RPM measurement • Commutation of brushless DC motors Rpu OUT Pin 3 (Blue) Dimensions Dimensions in mm (inch) Two-wire version illustrated. 23.00 (.906) 6.00 (.236) 7.50 (.295) 14.00 (.551) Encapsulant excluded 300 (11.81) 6.35 NOM. (.250) 9.00 (.374) 11.00 (.433) Centre of Sensitivity 3.00 (.118) 14.00 (.551) 3.20x3.81 TYP. Slot (.12x.150) © 2015 Littelfuse Revised: 11/02/15 Specifications are subject to change without notice. General Tol.: ±(.005) 0.13 littelfuse.com Hall Effect Sensors Flange Mount > 55140 55140 Miniature Flange Mounting Sensor Electrical Ratings Digital Switch Three-Wire (Voltage Output) Digital Switch Two-Wire (Current Output) Vdc Vdc Vdc - max. -15 to +28 +3.8 to +24 32 -15 to +28 +3.75 to +24 32 8.5 4.5 - 5.5 19.5 Output High Voltage Vdc - min. Sinking output N/A 4.65 Output Low Voltage Vdc - max. 0.4 @ 20mA N/A 0.35 Output Current (continuously on) mA - max. 20 N/A -1.0 to +1.0 mA - min. mA - max. 1.6 - 5.2 1.6 - 5.2 5.0 - 6.9 12.0 - 17.0 2.0 - 10.0 2.0 - 10.0 kHz 10 10 2 °C -40 to +100 -40 to +100 -40 to +100 Hall Type Supply Voltage 1 Absolute Ratings Operate Overvoltage Protection Current Consumption Over Temperature Range Low High Switching Speed Temperature Operating A - Analogue (Programmable Only) 2 Notes: 1. As long as Tj (Junction Temperature) is not exceeded. It is recommended to operate within the normal Operate Supply Voltage of +24Vdc maximum. Operating beyond Absolute Ratings may cause permanent damage to the Hall IC. 2. Preprogrammed by Littelfuse or Customer pending agreement. 3. For custom modifications to the wire length or size, or adding a special connector, please contact Littelfuse. © 2015 Littelfuse Revised: 11/02/15 Specifications are subject to change without notice. littelfuse.com Hall Effect Sensors Flange Mount > 55140 55140 Miniature Flange Mounting Sensor Hall Options Select Option Hall Type Sensitivity Gauss (typ.) Activate - D mm (inch) 2M 2 Wire Switch 120 13.5 (.531) 2H 2 Wire Switch 57 18.5 (.728) 3M 3 Wire Switch 130 12.5 (.492) 3H 3 Wire Switch 59 18.0 (709) AP Analog Programmable Consult Littelfuse Termination Specification D N Termination Options S Select Option Description (Two-wire versions illustrated) A Tinned leads (6.4±0.76)mm Note: Active distances are approximate using NEFEB Magnet 21 x 7 x 4.7 (.827L x .276W x .185H) LITTELFUSE P/N H-58 F Untinned leads (6.4±0.76)mm Cable Length Options E JST type XHP 2.5mm pitch Cable Type: 24AWG 7/32 PVC 105°C UL 1430/UL1569 Select Option Cable Length mm (inch) 02 300 (11.81) Part Numbering System 55140 - XX - XX - X Series Hall Option 2M, 2H, 3M, 3H, or AP Cable Length 02 Termination A, E, or F Packaging Packaging Option Packaging Specification Bulk © 2015 Littelfuse Revised: 11/02/15 Specifications are subject to change without notice. Bulk Quantity 500 Quantity & Packaging Code N/A Taping Width N/A littelfuse.com