DATA SHEET SE2442L: 902 to 928 MHz High-Power RF Front-End Module CTX In-home appliances CSD PA _OUT Smart meters TX_IN Applications Smart thermostats Logic control Features PA _IN PA Integrated PA with +30 dBm output power Receive pass-through Integrated antenna switching Single-ended 50 Ω Tx and Rx RF interface ANT RX_OUT Fast turn-on / turn-off time < 1 μsec Y0906 2.0 V to 4.8 V supply operation Figure 1. SE2442L Block Diagram Sleep mode current < 1 μA 4 x 4 x 0.9 mm 24-pin QFN Small QFN (24-pin, 4 mm x 4 mm x 0.9 mm) package (MSL1, 260°C per JEDEC J-STD-020) TM Skyworks Green products are compliant with all applicable legislation and are halogen-free. For additional information, refer to Skyworks Definition of GreenTM, document number SQ04–0074. Description The SE2442L is a high-performance, integrated RF front-end module designed for high-power ISM band applications operating in the 902 to 928 MHz frequency band. The SE2442L is designed for ease of use and maximum flexibility, with fully matched 50 Ω input and output, and digital controls compatible with 1.6 to 3.6 V CMOS levels. The RF blocks operate over a wide supply voltage range from 2.0 to 4.8 V, allowing the SE2442L to be used in battery powered applications over a wide spectrum of the battery discharge curve. A functional block diagram is shown in Figure 1. The pin configuration and package are shown in Figure 2. Signal pin assignments and functional pin descriptions are provided in Table 1. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202415C • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 18, 2015 1 19 DNC 20 PA_OUT 21 VCC2 22 DNC 23 VCC0 24 VCC1 DATA SHEET • SE2442L: 902 TO 928 MHz HIGH-POWER RF FRONT-END MODULE 2 17 GND GND 3 16 TX_IN CTX 4 15 GND DNC 5 14 DNC RX_OUT 6 13 GND DNC 10 DNC 8 GND DNC ANT 12 PA_IN DNC 11 18 GND 9 1 7 CSD Y2592 Figure 2. SE2442L Pinout (Top View) Table 1. SE2442L Signal Descriptions Pin Name Description Pin Name Description 1 CSD Shutdown control input 13 GND Ground 2 PA_IN PA input 14 DNC Do not connect 3 GND Ground 15 GND Ground 4 CTX Transmit enable control input 16 TX_IN Tx signal to antenna switch (from OMN) 5 DNC Do not connect 17 GND Ground 6 RX_OUT Receive signal to transceiver or SoC 18 GND Ground 7 DNC Do not connect 19 DNC Do not connect 8 GND Ground 20 PA_OUT PA output (to OMN) 9 DNC Do not connect 21 VCC2 Positive power supply, transmit section 10 DNC Do not connect 22 DNC Do not connect 11 DNC Do not connect 23 VCC0 Positive power supply, receive section 12 ANT Antenna port 24 VCC1 Positive power supply, transmit section Paddle GND Exposed die paddle; electrical and thermal ground (connect to PCB ground) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 2 November 18, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202415C DATA SHEET • SE2442L: 902 TO 928 MHz HIGH-POWER RF FRONT-END MODULE Electrical and Mechanical Specifications The absolute maximum ratings of the SE2442L are provided in Table 2. The recommended operating conditions are specified in Table 3, and electrical specifications are provided in Tables 4 through 6. The state of the SE2442L is determined by the logic provided in Table 7. Table 2. SE2442L Absolute Maximum Ratings (Note 1) Parameter Symbol Minimum Maximum Units 5.5 V Supply voltage receive VCC0 –0.3 Supply voltage transmit – no RF VCC1, VCC2 –0.3 5.5 V –0.3 VCC0 V Control pin voltages Operating temperature TOP –40 +85 °C Storage temperature TSTG –40 +125 °C Tx input power at PA_IN port PIN_Tx_MAX +10 dBm Rx input power at ANT port PIN_Rx_MAX +10 dBm Electrostatic discharge: ESD 1000 V Human Body Model (HBM) Note 1: Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device. CAUTION: Although this device is designed to be as robust as possible, electrostatic discharge (ESD) can damage this device. This device must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times. Table 3. Recommended Operating Conditions Minimum Typical Maximum Units Ambient temperature Parameter TA Symbol –40 +25 +85 C Supply voltage on VCC0, VCC1, and VCC2 VCC 2.0 3.6 4.8 V Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202415C • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 18, 2015 3 DATA SHEET • SE2442L: 902 TO 928 MHz HIGH-POWER RF FRONT-END MODULE Table 4. SE2442L Electrical Specifications: DC (Note 1) (VCC = 3.6 V, TA = +25 C, as Measured on the Evaluation Board [De-Embedded to the Device], Unless Otherwise Noted) Parameter Symbol ICC_TX30 TX supply current ICC_TX27 TX supply current ICQ_TX Quiescent current ICC_RXBYPASS RX supply current Sleep supply current ICC_OFF Test Condition Min Typical Max Units Tx mode POUT = +30 dBm CSD = CTX = high, VCC = 4.8 V 420 mA Tx mode POUT = 27 dBm CSD = CTX = high, VCC = 3.6 V 280 mA No RF CSD = CTX = high 50 mA Rx bypass mode CSD = HIGH, CTX = 0 V No RF, CTX = CSD = 0 V 0.05 280 μA 1 μA Max Units V Note 1: Performance is guaranteed only under the conditions listed in the above table. Table 5. SE2442L Electrical Specifications: Logic Characteristics (Note 1) (TA = +25 C, as Measured on the Evaluation Board [De-Embedded to the Device], Unless Otherwise Noted) Parameter Symbol Test Condition Min Typical Logic input high voltage VIH 1.6 VCC0 Logic input low voltage VIL 0 0.3 V Logic input high current IIH 1 μA Logic input low current IIL 1 μA Note 1: Performance is guaranteed only under the conditions listed in the above table. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 4 November 18, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202415C DATA SHEET • SE2442L: 902 TO 928 MHz HIGH-POWER RF FRONT-END MODULE Table 6. SE2442L Electrical Specifications: AC Characteristics (Note 1) (VCC = 3.6 V, TA = +25 C, as Measured on Evaluation Board [De-Embedded to the Device], All Unused Ports Terminated with 50 Ω, Unless Otherwise Noted) Parameter Symbol Test Condition Min Typical Max Units 902 - 928 MHz Transmit (Tx) Frequency range FIN 31.5 30.0 29.0 27.5 dBm dBm dBm dBm 64 % Output power at ANT port Pout_FEM VCC = 4.8 V VCC = 4.0 V VCC = 3.6 V VCC = 3.0 V PA power added efficiency PAE Pout = +28 dBm at PA_OUT port, 915 MHz Small signal gain S21 902 to 928 MHz Small signal gain variation ∆S21 Gain variation across frequency range Output return loss S22ANT Into 50 , ANT port 2 harmonic HD2 3rd to 10th harmonics HD3 to HD10 Turn on time TON Turn off time TOFF Stability STAB CW, PIN = +6 dBm 0.1 GHz – 20 GHz Load VSWR = 6:1 All non-harmonically related outputs <–42.0 dBm/MHz Ruggedness RU CW, Pout = 27 dBm into 50 Ω, Load VSWR = 10:1 No permanent damage nd 20 dB 1 dBp-p –6 dB POUT = +27 dBm, CW –22 dBc POUT = +27 dBm, CW –72 dBc From 50% of CTX edge to 90% of final RF output power 1 μs From 50% of CTX edge to 10% of final RF output power 1 μs -10 Receive (Rx) (Note 2) Frequency range fIN 902 932 MHz Antenna port return loss S11ANT Into 50 , ANT port –6 dB Turn on time TON Turn off time TOFF From 50% of CTX edge 1 μs From 50% of CTX edge 1 μs Gain in bypass mode G_bp CTX = logic ‘0’ and CSD = logic ‘1’ Input 1-dB compression point in bypass mode IP1dB CTX = logic ‘0’ and CSD = logic ‘1’ Insertion loss from TX_IN to ANT Tx_ANT 902 to 928 MHz - 0.7 - dB Insertion loss from ANT to RX_OUT Rx_ANT 902 to 928 MHz - 0.7 - dB –10 –0.7 dB 10 dB Antenna Functions Note 1: Performance is guaranteed only under the conditions listed in this table. Note 2: Receive section can operate with VCC0 = 2.8 V and VCC1 = VCC2 = 0 V Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202415C • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 18, 2015 5 DATA SHEET • SE2442L: 902 TO 928 MHz HIGH-POWER RF FRONT-END MODULE Table 7. SE2442L Logic Controls (TA = +25 C) Mode Description CSD CTX 0 All off (sleep mode) (Notes 1 and 3) 0 0 1 Rx or Tx bypass mode (Notes 1 and 2) 1 0 3 Tx mode (Notes 1 and 2) 1 1 Note 1: Logic ‘0’ level compliant to VIL as specified in Table 5. Note 2: Logic ‘1’ level compliant to VIH as specified in Table 5. Note 3: All controls must be at logic ‘0’ in order to achieve the specified sleep current. Evaluation Board Description Measure TX Performance The SE2442L Evaluation Board is used to test the performance of the SE2442L front-end module (FEM). An Evaluation Board schematic diagram is provided in Figure 3. A photograph of the Evaluation Board is shown in Figure 4. A Bill of Materials (BOM) for the Evaluation Board is provided in Table 8. Apply an RF signal to connector J10 (PA_IN) to monitor the 900 to 930 MHz amplifier performance. Monitor the output power on connector J9 (ANT). Evaluation Board Setup Procedure Measure RX Performance Apply an RF signal to connector J9 (ANT) to monitor the 900 to 930 MHz RX path performance. Monitor the output signal on connector J11 (RX_OUT). Connect Supply 1. Connect J9, J10, and J11 to 50 Ω instruments. Terminate all unused ports (if applicable) with 50 Ω. 2. Connect the supply ground to Pin 1 of the J4 header. CAUTION: Care should be taken not to overdrive the amplifier by applying too much RF on the input to the device. A suitable starting input power for the device is –20 dBm. 3. Connect the DC power supply (2.0 to 4.8 V) to pin 2 of the J4 header. 4. Refer to Table 7 for information about selecting the required RF path. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 6 November 18, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202415C DATA SHEET • SE2431L: 2.4 GHz FRONT-END MODULE J4 VCC C3 4.7 uF CTX CSD VCC C1 10 nF C12 1 nF C2 100 pF C4 33 pF 2 4 6 8 10 12 1 3 5 7 9 11 C6 DNI L5 6.8 nH C5 120 pF CSD CTX CSD PA_IN GND CTX DNC RX_OUT 24 23 22 21 20 19 SE2442L U1 C9 4.7 pF GND GND TX_IN GND DNC GND 18 17 16 15 14 13 L2 8.2 nH C11 2.7 pF 7 8 9 10 11 12 DNC GND DNC DNC DNC ANT J11 SMA 1 2 3 4 5 6 C8 4 pF VCC1 VCC0 DNC VCC2 PA_OUT DNC 25 PAD J10 SMA L1 2.7 nH R1 DNI J9 SMA L4 6.8 nH L3 6.8 nH C10 2.7 pF C7 DNI Y2593 Figure 3. SE2442L Evaluation Board Schematic Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202415C • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 18, 2015 7 DATA SHEET • SE2442L: 902 TO 928 MHz HIGH-POWER RF FRONT-END MODULE Figure 4. SE2442L Evaluation Board Table 8. SE2442L Bill of Materials (BOM) Component Value Manufacturer Mfr Part Number Package Size Description C1 10 nF Murata GRM155R71E103KA01 0402 Multilayer ceramic C2 100 pF Murata GRM1555C1H101JZ01 0402 Multilayer ceramic C3 4.7 uF Murata GRM188R60J475KE19 0402 Multilayer ceramic C4 33 pF Murata GRM1555C1H330JZ01 0402 Multilayer ceramic C5 120 pF Murata GRM1555C1H121JA01 0402 Multilayer ceramic C6, C7 DNI 0402 Multilayer ceramic C8 4 pF Taiyo-Yuden UMK105CG040CW 0402 Standard multilayer ceramic capacitor C9 4.7 pF Murata GRM1555C1H4R7CZ01 0402 Multilayer ceramic C10, C11 2.7 pF Murata GRM1555C1H2R7CZ01 0402 Multilayer ceramic C12 1 nF Murata GRM155R71H102KA01 0402 Multilayer ceramic J1, J2, J3 SMA Johnson Components 142-0701-851 J4 6x2 Samtex TSW-106-07-G-D 100 mil L1 2.7 nH Murata LQG15HN2N7S02D 0402 Inductor L2 8.2 nH Murata LQG15HN8N2J02D 0402 High frequency multilayer L3, L4, L5 6.8 nH Murata LQG18HN6N8S00D 0603 High frequency multilayer Skyworks Z387-B PCB1 R1 U1 DNI End launch SE2442L 100 mil header PCB 0402 Skyworks SMA end launch straight jack receptacle - tab contact QFN400x400 Do not install 900-930 MHz High Power RF FEM Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 8 November 18, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202415C DATA SHEET • SE2442L: 902 TO 928 MHz HIGH-POWER RF FRONT-END MODULE Package Dimensions Package and Handling Information The PCB layout footprint for the SE2442L is provided in Figure 5. A typical part marking diagram is shown in Figure 6. Package dimensions are shown in Figure 7, and tape and reel dimensions are provided in Figure 8. Instructions on the shipping container label regarding exposure to moisture after the container seal is broken must be followed. Otherwise, problems related to moisture absorption may occur when the part is subjected to high temperatures during solder assembly. The SE2442L is rated to Moisture Sensitivity Level 1 (MSL1) at 260 °C, and can be used for lead or lead-free soldering. For additional information, refer to the Skyworks Application Note, Solder Reflow Information, document number 200164. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. Production quantities of this product are shipped in a standard tape and reel format. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202415C • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 18, 2015 9 5X 1.02 5X 0.51 5X 0.0 4.40 2.70 5X 0.51 5X 1.02 DATA SHEET • SE2442L: 902 TO 928 MHz HIGH-POWER RF FRONT-END MODULE 5X 1.02 5X 0.51 2.70 0 4.40 5X 0.0 5X 0.51 5X 1.02 0 0.60 Typ 0.25 Typ 25X Ø0.254 0.500 Typ Via Pattern (Note 4) Board Metal 4.50 2.50 4.40 0.20 Typ 1.00 Typ 1.00 Typ 2.50 4.50 4.40 0.20 Typ 0.60 Typ 0.70 Typ 0.35 Typ 0.500 Typ Package Outline 0.25 Typ 0.500 Typ Stencil Pattern (Note 5) 64% Solder Coverage on Center Pad Solder Mask Pattern (Note 6) Notes: 1. 2. 3. 4. All dimensions are in millimeters. Interpret dimensions and tolerances per ASME Y14.5M-1994. Unless specified, dimensions are symmetrical about center lines. Via hole recommendations: 0.025 mm Cu via wall plating (minimum), via hole to be filled with conductive paste and plated over. 5. Stencil recommendations: 0.125 mm stencil thickness, laser cut apertures, trapezoidal walls and rounded corners offer the best paste release. 6. Solder mask recommendations: Contact board fabricator for recommended solder mask offset and tolerance. Y2596 Figure 5. PCB Layout Footprint Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 10 November 18, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202415C DATA SHEET • SE2442L: 902 TO 928 MHz HIGH-POWER RF FRONT-END MODULE Pin 1 Indicator Material Finish Symbol Skyworks Part Number Lot Code Y2597 Figure 6. SE2442L Typical Part Marking 4.00 ±0.05 A 0.85 ±0.05 0.05 C 2.70 ±0.05 0.203 Ref 0.30 X 45° B 0.000-0.005 Pin 1 Indicator Pin 1 Indicator Exposed Pad 4.00 ±0.05 2.70 ±0.05 0.500 R0.075 Typ 24X 0.20 Min 0.05 C 25X 2X 0.08 C Top View See Detail B See Detail A 4 C 0.05 C Seating Plane 2X Bottom View Side View Notes: 0.093 ±0.05 1. All measurements are in millimeters. 2. Dimensions and tolerances according to ASME Y14.5M-2009. 3. Unless otherwise specified, the following values apply: Decimal Tolerance: Angular Tolerance: X.X (1 place) ± 0.1 mm ±1/2° X.XX (2 places) ± 0.05 mm X.XXX (3 places) ± 0.025 mm 4. Coplanarity applies to the exposed center ground pad as well as the terminals. 5. Dimension applies to the metallized terminal. If the terminal has a radius, the dimension should not be measured in that radius area. 6. Plating requirements per Source Control Drawing (SCD) 2504. 7. Unless specified, dimensions are symmetrical about center lines. 2X R0.075 R0.075 0.40 ±0.05 0.40 ±0.05 0.307 ±0.05 0.25 ±0.05 0.10 0.05 5 C A B C Detail A Scale 2X (16 Places) 0.25 ±0.05 5 0.10 0.05 C A B C Detail B Scale 2X (8 Places) Y2598 Figure 7. SE2442L Package Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202415C • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 18, 2015 11 DATA SHEET • SE2442L: 902 TO 928 MHz HIGH-POWER RF FRONT-END MODULE 8.0 ±0.1 D 1.50 +0.10 4.0 Note 1 1.75 ±0.1 2.0 ±0.05 1.22 ±0.1 0.254 ±0.013 5.5 ±0.05 12.0 ±0.3 4.35 ±0.1 4.35 ±0.1 Pin 1 Indicator Notes: 1. 10-Sprocket hole pitch cumulative tolerance ±0.2. 2. Camber in compliance with EIA-481. Y0086 Figure 8. SE2442L-R Tape and Reel Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 12 November 18, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202415C DATA SHEET • SE2442L: 902 TO 928 MHz HIGH-POWER RF FRONT-END MODULE Ordering Information Model Name SE2442L: 902 to 928 MHz Front-End Module Manufacturing Part Number SE2442L Evaluation Board Part Number SE2442L-EK1 Copyright © 2012-2015 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks and the Skyworks symbol are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202415C • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 18, 2015 13