DNT04S0A0S05

FEATURES

High Efficiency: 93.5%@ 5Vin, 3.3V/5A out

Small size and low profile:
0.80” x 0.45” x 0.27” (SMD)
0.90” x 0.40” x 0.25” (SIP)

Standard footprint and pinout

Resistor-based trim

Output voltage programmable from
0.75V to 3.63V via external resistors

Pre-bias startup

No minimum load required

Fixed frequency operation

Input UVLO, OCP

Remote ON/OFF

ISO 9001, TL 9000, ISO 14001, QS 9000,
OHSAS 18001 certified manufacturing
facility

UL/cUL 60950 (US & Canada) Recognized,
and TUV (EN60950) certified

CE mark meets 73/23/EEC and 93/68/EEC
directive
Delphi DNT04, Non-Isolated Point of Load
DC/DC Power Modules: 2.4~5.5Vin, 0.75~3.63Vo, 5A out
OPTIONS
The Delphi Series DNT04, 2.4-5.5V input, single output, non-isolated
Point of Load DC/DC converters are the latest offering from a world

Positive On/Off logic

SIP package
leader in power systems technology and manufacturing — Delta
Electronics, Inc. The DNT04 series provides a programmable output
voltage from 0.75V to 3.63V using external resistors. This product family
is available in surface mount or SIP package and provides up to 5A of
output current in an industry standard footprint. With creative design
technology and optimization of component placement, these converters
possess outstanding electrical and thermal performance, as well as
APPLICATIONS
extremely high reliability under highly stressful operating conditions.

Telecom/DataCom

Distributed power architectures

Servers and workstations

LAN/WAN applications

Data processing applications
The DNT04, 5A modules have excellent thermal performance and can
provide full output current at up to 85℃ ambient temperature with no
airflow.
DS_DNT04SMD05_07182012
TECHNICAL SPECIFICATIONS
(TA = 25°C, airflow rate = 300 LFM, Vin = 5Vdc, nominal Vout unless otherwise noted.)
PARAMETER
NOTES and CONDITIONS
DNT04S0A0S05NFA
Min.
ABSOLUTE MAXIMUM RATINGS
Input Voltage (Continuous)
Operating Temperature
Storage Temperature
INPUT CHARACTERISTICS
Operating Input Voltage
Input Under-Voltage Lockout
Turn-On Voltage Threshold
Turn-Off Voltage Threshold
Maximum Input Current
No-Load Input Current
Off Converter Input Current
Inrush Transient
Recommended Input Fuse
OUTPUT CHARACTERISTICS
Output Voltage Set Point
Output Voltage Adjustable Range
Output Voltage Regulation
Over Line
Over Load
Over Temperature
Total Output Voltage Range
Output Voltage Ripple and Noise
Peak-to-Peak
RMS
Output Current Range
Output Voltage Over-shoot at Start-up
Output DC Current-Limit Inception
Output Short-Circuit Current (Hiccup Mode)
DYNAMIC CHARACTERISTICS
Dynamic Load Response
Positive Step Change in Output Current
Negative Step Change in Output Current
Setting Time to 10% of Peak Devitation
Turn-On Transient
Start-Up Time, From On/Off Control
Start-Up Time, From Input
Maximum Output Startup Capacitive Load
EFFICIENCY
Vo=3.3V
Vo=2.5V
Vo=1.8V
Vo=1.5V
Vo=1.2V
Vo=0.75V
FEATURE CHARACTERISTICS
Switching Frequency
ON/OFF Control, (For Negative logic)
Logic Low Voltage
Logic High Voltage
Logic Low Current
Logic High Current
ON/OFF Control, (For Positive logic)
Logic HighVoltage
Logic Low Voltage
Logic High Current
Logic Low Current
GENERAL SPECIFICATIONS
MTBF
Weight
Vo ≦ Vin –0.5V
Typ.
Max.
Units
0
-40
-55
5.8
85
125
Vdc
°C
°C
2.4
5.5
V
2.05
1.90
Vin=4.5V
Vo=3.3V, Io=Io, max
30
2
Vin=2.4V to 5.5V, Io=Io, min to Io, max
Vin=5V, Io=Io, max
-2.5
0.7525
Vin=2.4V to 5.5V
Io=Io, min to Io, max
Ta=-40℃ to 85℃
Over sample load, line and temperature
5Hz to 20MHz bandwidth
Full Load, 1µF ceramic, 10µF tantalum
Full Load, 1µF ceramic, 10µF tantalum
Vo,set
-3.0
30
10
Io, s/c
10µF Tantalum & 1µF Ceramic load cap, 2.5A/µs
50% Io, max to 100% Io, max
100% Io, max to 50% Io, max
Io=Io.max
Von/off, Vo=10% of Vo,set
Vin=Vin, min, Vo=10% of Vo,set
Full load; ESR ≧1mΩ
Full load; ESR ≧10mΩ
Io=100% of Io, max;
+3.0
% Vo,set
% Vo,set
% Vo,set
% Vo,set
200
2.2
mV
mV
A
% Vo,set
% Io
Adc (rms)
100
100
25
mV
mV
µs
8.5
8.5
ms
ms
µF
µF
50
15
5
1
93.5
91.0
88.5
86.5
83.5
77.0
%
%
%
%
%
%
300
kHz
-0.2
2.5
0.2
0.3
Vin.max
10
1
V
V
µA
mA
0.2
Vin.max
0.3
10
1
V
V
µA
mA
-0.2
Airflow=200LFM, Ta=25°C
% Vo,set
V
1000
3000
Vin=5V, 100% Load
Vin=5V, 100% Load
Vin=5V, 100% Load
Vin=5V, 100% Load
Vin=5V, 100% Load
Vin=5V, 100% Load
Module On, Von/off
Module Off, Von/off
Module On, Ion/off
Module Off, Ion/off
+2.5
3.63
4.1
45
0.2
0.2
0.4
0
Module On, Von/off
Module Off, Von/off
Module On, Ion/off
Module Off, Ion/off
0.1
5
V
V
A
mA
mA
2
AS
A
19.38
2.3
M hours
grams
DS_DNT04SMD05_07182012
2
96
96
95
94
Efficiency (%)
Efficiency (%)
ELECTRICAL CHARACTERISTICS CURVES
94
93
92
91
92
90
88
86
90
84
1
2
3
4
5
1
2
Figure 1: Converter efficiency vs. output current (5Vin/3.3Vout)
5
92
90
Efficiency (%)
90
Efficiency (%)
4
Figure 2: Converter efficiency vs. output current (5Vin/2.5Vout)
92
88
86
84
88
86
84
82
82
1
2
3
4
80
5
1
2
Out put cur r ent ( A)
3
4
5
Out put cur r ent ( A)
Figure 3: Converter efficiency vs. output current (5Vin/1.8Vout)
Figure 4: Converter efficiency vs. output current (5Vin/1.5Vout)
90
86
88
84
Efficiency (%)
Efficiency (%)
3
Out put cur r ent ( A)
Out put cur r ent ( A)
86
84
82
80
82
80
78
76
74
78
1
2
3
4
5
Out put cur r ent ( A)
Figure 5: Converter efficiency vs. output current (5Vin/1.2Vout)
1
2
3
4
5
Out put cur r ent ( A)
Figure 6: Converter efficiency vs. output current (5Vin/0.75Vout)
DS_DNT04SMD05_07182012
3
ELECTRICAL CHARACTERISTICS CURVES (CON.)
Figure 7: Output ripple & noise at 5Vin, 3.3V/5A out
Figure 8: Output ripple & noise at 5Vin, 2.5V/5A out
Figure 9: Output ripple & noise at 5Vin, 1.8V/5A out
Figure 10: Output ripple & noise at 5Vin, 1.5V/5A out
Figure 11: Output ripple and noise at 5Vin, 1.2V/5A out
Figure 12: Output ripple and noise , 0.75V/5A out
DS_DNT04SMD05_07182012
4
ELECTRICAL CHARACTERISTICS CURVES (CON.)
Figure 13: Turn on delay time at 5Vin, 3.3V/5A out
Top: Vout, 2V/div, Bottom: Vin, 2V/div; 2mS/div
Figure 15: Turn on delay time at 5Vin, 1.8V5A out
Top: Vout, 2V/div, Bottom: Vin, 2V/div; 2mS/div
Figure 17: Turn on delay time at 5Vin, 1.2V/5A out
Top: Vout , 2V/div, Bottom :Vin, 2V/div; 2mS/div
Figure 14: Turn on delay time at 5Vin, 2.5V/5A out
Top: Vout, 2V/div, Bottom: Vin, 2V/div; 2mS/div
Figure 16: Turn on delay time at 5Vin, 1.5V/5A out
Top: Vout, 2V/div, Bottom: 2V/div; 2mS/div
Figure 18: Turn on delay time at 5Vin, 0.75V/5A out
Top: Vout, 0.5V/div, Bottom: Vin , 2V/div; 2mS/div
DS_DNT04SMD05_07182012
5
ELECTRICAL CHARACTERISTICS CURVES
Figure 19: Typical transient response to step load change at
2.5A/μS from 100% to 50% of Io, max at 5Vin, 3.3Vout
(Cout = 1uF ceramic, 10μF tantalum)
(100mV/div, 10uS/div)
Figure 20: Typical transient response to step load change at
2.5A/μS from 50% to 100% of Io, max at 5Vin, 3.3Vout
(Cout =1uF ceramic, 10μF tantalum)
(100mV/div, 10uS/div)
Vbias=1V
Figure 21: Output short circuit current 5Vin, 0.75Vout
5A/div, 10mS/div
Figure 22: Turn on with Prebias 5Vin, 3.3V/0A out, Vbias =1.0Vdc
2V/div, 10mS/div
DS_DNT04SMD05_07182012
6
DESIGN CONSIDERATIONS
TEST CONFIGURATIONS
Input Source Impedance
L
VI(+)
2 100uF
Tantalum
BATTERY
VI(-)
Note: Input reflected-ripple current is measured with a
simulated source inductance. Current is measured at the input
of the module.
Vo
SCOPE
Safety Considerations
For safety-agency approval the power module must be
installed in compliance with the spacing and separation
requirements of the end-use safety agency standards.
Figure 23: Input reflected-ripple test setup
1uF
10uF
tantalum ceramic
The power module should be connected to a low
ac-impedance input source. Highly inductive source
impedances can affect the stability of the module. An
input capacitance must be placed close to the modules
input pins to filter ripple current and ensure module
stability in the presence of inductive traces that supply
the input voltage to the module.
Resistive
Load
For the converter output to be considered meeting the
requirements of safety extra-low voltage (SELV), the
input must meet SELV requirements. The power module
has extra-low voltage (ELV) outputs when all inputs are
ELV.
The input to these units is to be provided with an
adequate time-delay fuse in the ungrounded lead.
GND
Note: Use a 10μF tantalum and 1μF capacitor. Scope
measurement should be made using a BNC connector.
Figure 24: Peak-peak output noise and startup transient
measurement test setup.
VI
Vo
GND
Figure 25: Output voltage and efficiency measurement test
setup
Note: All measurements are taken at the module terminals.
When the module is not soldered (via socket), place
Kelvin connections at module terminals to avoid
measurement errors due to contact resistance.
(
Vo  Io
)  100 %
Vi  Ii
DS_DNT04SMD05_07182012
7
FEATURES DESCRIPTIONS
FEATURES DESCRIPTIONS (CON.)
Remote On/Off
Output Voltage Programming
The DNT series power modules have an On/Off pin for
remote On/Off operation. Both positive and negative
On/Off logic options are available in the DNT series
power modules.
The output voltage of the DNT can be programmed to any
voltage between 0.75Vdc and 3.63Vdc by connecting one
resistor (shown as Rtrim in Figure 28) between the TRIM
and GND pins of the module. Without this external
resistor, the output voltage of the module is 0.7525 Vdc.
To calculate the value of the resistor Rtrim for a particular
output voltage Vo, please use the following equation:
For positive logic module, connect an open collector
(NPN) transistor or open drain (N channel) MOSFET
between the On/Off pin and the GND pin (see figure 26).
Positive logic On/Off signal turns the module ON during
the logic high and turns the module OFF during the logic
low. When the positive On/Off function is not used, leave
the pin floating or tie to Vin (module will be On).
For negative logic module, the On/Off pin is pulled high
with an external pull-up resistor (see figure 27). Negative
logic On/Off signal turns the module OFF during logic
high and turns the module ON during logic low. If the
negative On/Off function is not used, leave the pin
floating or tie to GND. (module will be On)
Vo
V in
I O N /O F F
O n/O ff
RL
Q1
GND
 21070

Rtrim  
 5110 
Vo  0.7525

For example, to program the output voltage of the DNT
module to 1.8Vdc, Rtrim is calculated as follows:
 21070

Rtrim  
 5110   15K
1.8  0.7525

DNT can also be programmed by apply a voltage
between the TRIM and GND pins (Figure 29). The
following equation can be used to determine the value of
Vtrim needed for a desired output voltage Vo:
Vtrim  0.7  0.1698  Vo  0.7525
For example, to program the output voltage of a DNT
module to 3.3 Vdc, Vtrim is calculated as follows
Vtrim  0.7  0.1698 3.3  0.7525  0.267V
Figure 26: Positive remote On/Off implementation
Vo
Vo
Vin
Rpullup
I O N /O FF
RLoad
TRIM
Rtrim
On/Off
RL
GND
Q1
Figure28: Circuit configuration for programming output voltage
GND
using an external resistor
Figure 27: Negative remote On/Off implementation
Over-Current Protection
To provide protection in an output over load fault
condition, the unit is equipped with internal over-current
protection. When the over-current protection is
triggered, the unit enters hiccup mode. The units operate
normally once the fault condition is removed.
DS_DNT04SMD05_07182012
8
FEATURE DESCRIPTIONS (CON.)
Table 1 provides Rtrim values required for some common
output voltages, while Table 2 provides value of external
voltage source, Vtrim, for the same common output
voltages. By using a 1% tolerance trim resistor, set point
tolerance of ±2% can be achieved as specified in the
electrical specification.
Vo
Vtrim
RLoad
TRIM
GND
+
_
Table 1
VO (V)
0.7525
1.2
1.5
1.8
2.5
3.3
3.63
Rtrim (KΩ)
Open
41.973
23.077
15.004
6.947
3.160
2.212
Table 2
VO (V)
0.7525
1.2
1.5
1.8
2.5
3.3
3.63
Vtrim (V)
Open
0.6240
0.5731
0.5221
0.4033
0.2674
0.2114
Figure 29: Circuit Configuration for programming output voltage
using external voltage source
The amount of power delivered by the module is the
voltage at the output terminals multiplied by the output
current. When using the trim feature, the output voltage of
the module can be increased, which at the same output
current would increase the power output of the module.
Care should be taken to ensure that the maximum output
power of the module must not exceed the maximum rated
power (Vo.set x Io.max ≤ P max).
Voltage Margining
Output voltage margining can be implemented in the DNT
modules by connecting a resistor, R margin-up, from the Trim
pin to the ground pin for margining-up the output voltage
and by connecting a resistor, R margin-down, from the Trim pin
to the output pin for margining-down. Figure 32 shows the
circuit configuration for output voltage margining. If unused,
leave the trim pin unconnected. A calculation tool is
available from the evaluation procedure which computes
the values of R margin-up and Rmargin-down for a specific output
voltage and margin percentage.
Vin
Vo
Rmargin-down
Q1
On/Off Trim
Rmargin-up
Rtrim
Q2
GND
Figure 30: Circuit configuration for output voltage margining
DS_DNT04SMD05_07182012
9
THERMAL CONSIDERATIONS
THERMAL CURVES
Thermal management is an important part of the system
design. To ensure proper, reliable operation, sufficient
cooling of the power module is needed over the entire
temperature range of the module. Convection cooling is
usually the dominant mode of heat transfer.
Hence, the choice of equipment to characterize the
thermal performance of the power module is a wind
tunnel.
Thermal Testing Setup
Delta’s DC/DC power modules are characterized in
heated vertical wind tunnels that simulate the thermal
environments encountered in most electronics equipment.
This type of equipment commonly uses vertically mounted
circuit cards in cabinet racks in which the power modules
are mounted.
Figure 32: Temperature measurement location
The allowed maximum hot spot temperature is defined at 125℃
DNT04S0A0S05(standard) Output Current vs. Ambient Temperature and Air Velocity
@Vin =5V,Vo=0.75V~3.3V (Either Orientation)
Output Current (A)
The following figure shows the wind tunnel
characterization setup. The power module is mounted on
a test PWB and is vertically positioned within the wind
tunnel. The height of this fan duct is constantly kept at
25.4mm (1’’).
5.0
Natural
Convection
4.0
3.0
Thermal Derating
2.0
Heat can be removed by increasing airflow over the
module. To enhance system reliability, the power module
should always be operated below the maximum operating
temperature. If the temperature exceeds the maximum
module temperature, reliability of the unit may be affected.
PWB
FANCING PWB
1.0
0.0
50
55
60
65
70
75
80
85
Ambient Temperature (℃)
Figure 33: Derating curves, output current vs. ambient
temperature and air velocity @ Vin=5V, Vout=0.75V~3.3V (Either
Orientation)
MODULE
50.8(2.00")
AIR VELOCITY
AND AMBIENT
TEMPERATURE
SURED BELOW
THE MODULE
AIR FLOW
Note: Wind Tunnel Test Setup Figure Dimensions are in millimeters and (Inches)
Figure 31: Wind tunnel test setup
DS_DNT04SMD05_07182012
10
PICK AND PLACE LOCATION
SURFACE- MOUNT TAPE & REEL
LEAD (Sn/Pb) PROCESS RECOMMEND TEMP. PROFILE
LEAD FREE (SAC) PROCESS RECOMMEND TEMP. PROFILE
Temp.
Peak Temp. 240 ~ 245 ℃
220℃
Ramp down
max. 4℃ /sec.
200℃
150℃
Preheat time
90~120 sec.
Time Limited 75 sec.
above 220℃
Ramp up
max. 3℃ /sec.
25℃
Time
Note: All temperature refers to assembly application board, measured on the land of assembly application board.
DS_DNT04SMD05_07182012
11
MECHANICAL DRAWING
SMD PACKAGE
SIP PACKAGE (OPTIONAL)
DS_DNT04SMD05_07182012
12
PART NUMBERING SYSTEM
DNT
04
S
0A0
S
05
N
Product
Series
Input Voltage
Numbers
of Outputs
Output
Voltage
Package
Type
Output
Current
On/Off logic
DNT- 3A/5A
04 - 2.4V~5.5V
S - Single
0A0 Programmable
R - SIP
03 - 3A
S - SMD
05 - 5A
F
A
Option Code
N - Negative F- RoHS 6/6
P - Positive
(Lead Free)
A - Standard Function
MODEL LIST
Model Name
Package
Input Voltage
Output Voltage
Output Current
Efficiency
5Vin, 3.3Vdc full load
DNT04S0A0S03NFA
SMD
2.4V ~ 5.5Vdc
0.75V ~ 3.63Vdc
3A
93.0%
DNT04S0A0R03NFA
SIP
2.4V ~ 5.5Vdc
0.75V ~ 3.63Vdc
3A
94.0%
DNT04S0A0S05NFA
SMD
2.4V ~ 5.5Vdc
0.75V ~ 3.63Vdc
5A
93.5%
DNT04S0A0R05NFA
SIP
2.4V ~ 5.5Vdc
0.75V ~ 3.63Vdc
5A
93.0%
CONTACT: www.deltaww.com/dcdc
USA:
Telephone:
East Coast: 978-656-3993
West Coast: 510-668-5100
Fax: (978) 656 3964
Email: [email protected]
Europe:
Telephone: +31-20-655-0967
Fax: +31-20-655-0999
Email: [email protected]
Asia & the rest of world:
Telephone: +886 3 4526107 x6220~6224
Fax: +886 3 4513485
Email: [email protected]
WARRANTY
Delta offers a two (2) year limited warranty. Complete warranty information is listed on our web site or is available upon
request from Delta.
Information furnished by Delta is believed to be accurate and reliable. However, no responsibility is assumed by Delta
for its use, nor for any infringements of patents or other rights of third parties, which may result from its use. No license
is granted by implication or otherwise under any patent or patent rights of Delta. Delta reserves the right to revise these
specifications at any time, without notice.
DS_DNT04SMD05_07182012
13