36.15 MHz SAW Filter 8 MHz Bandwidth Part Number: SF0036BA11932S DESCRIPTION • • • 36.15 MHz SAW bandpass filter with 8 MHz bandwidth for Broadband Access. 24.6 x 9 mm SMP. RoHS compliant. TYPICAL PERFORMANCE Horizontal: Vertical from top: S11 (32.15 to 40.15 MHz) Frequency : Relative Magnitude : Relative magnitude : Phase Linearity : Group Delay Deviation : 2.5 10 1 10 100 MHz/div dB/div dB/div deg/div ns/div S22 (32.15 to 40.15 MHz) Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0036BA11932S Rev A 4-Feb-2010 ECN 36650 Page 1 of 3 36.15 MHz SAW Filter 8 MHz Bandwidth Part Number: SF0036BA11932S SPECIFICATION Parameter Center Frequency ( Fc) 1 Insertion Loss 2 1 dB Bandwidth 3 dB Bandwidth 38 dB Bandwidth Passband Amplitude Ripple 3 Passband Phase Ripple 3 Passband Group Delay Ripple 3 Rejection (10 to 30.9 MHz) Rejection (41.5 to 55 MHz) Absolute Delay Ambient Temperature Source / Load Impedance Substrate Material Notes: 1. 2. 3. 4. Min 36.1 7.60 8.00 35 33 - Typ Max Units 36.15 36.2 MHz 22 23 dB 7.75 MHz 8.20 MHz 10.00 10.50 MHz 0.5 0.7 dB p-p 2.2 3 deg p-p 30 60 ns p-p 40 dB 40 dB 1.50 µs 25 ºC 50 Ω 128 Lithium Niobate Defined as the average of the lower and upper 3 dB frequencies. Value at 36.15 MHz. Measured over Fc +/- 3.8 MHz. Specifications are guaranteed over the operating temperature range. MAXIMUM RATINGS Parameter Storage Temperature Range Operating Temperature Range Input Power Level Min Max -40 20 85 30 10 Units ˚C ˚C dBm MATCHING CIRCUIT 10 5 Input 50 Ω Single-ended Output 50 Ω Single-ended 1 6 GND GND Typical component values: (Minimum inductor Q = 40) Ls1 = 470 nH Ls2 = 560 nH Notes: 1. Recommend use of 5% tolerance matching components. 2. Component values may change depending on board layout. Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0036BA11932S Rev A 4-Feb-2010 ECN 36650 Page 2 of 3 36.15 MHz SAW Filter 8 MHz Bandwidth Part Number: SF0036BA11932S PACKAGE OUTLINE SUGGESTED FOOTPRINT Units: mm Package Material: Body: Al2O3 ceramic Lid: Kovar, Ni plated Terminations: Au plating 1 µm min, over a 1.3-8.9 µm Ni plating Tolerances are ±0.15 mm except for the overall length, width and pad dimensions, which are nominal values. Pad Configuration: Input: 10 Input return: 1 Output: 5 Output return: 6 Ground: 2,3,4,7,8,9 ISO 9001 Registered All specifications are believed to be accurate and reliable. However, Spectrum Microwave reserves the right to make changes without notice. © 2010 All rights reserved. Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0036BA11932S Rev A 4-Feb-2010 ECN 36650 Page 3 of 3