92.5 MHz SAW Filter 1.7 MHz Bandwidth Part Number SF0092CD02326S DESCRIPTION • • • 92.5 MHz SAW bandpass filter with 1.7 MHz bandwidth. 13.3 x 6.5 mm ceramic LCC package. RoHS compliant. TYPICAL PERFORMANCE Horizontal: Vertical: Frequency : Relative Magnitude : Relative Magnitude : Phase Linearity : Group Delay : 2 10 1 5 100 S11 (82.5-102.5 MHz) MHz/div dB/div dB/div deg/div ns/div S22 (82.5-102.5 MHz) Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0092CD02326S Rev A 22-Feb-2010 ECN 36650 Page 1 of 3 92.5 MHz SAW Filter 1.7 MHz Bandwidth Part Number SF0092CD02326S SPECIFICATION Parameter Center Frequency (Fc) 1 Insertion Loss at 92.5 MHz Amplitude Ripple (91.65 to 93.35 MHz) Lower 0.7dB Band Edge Frequency 3 Upper 0.7dB Band Edge Frequency 3 Lower 15dB Band Edge Frequency 3 Upper 15dB Band Edge Frequency 3 Lower 40dB Band Edge Frequency 3 Upper 40dB Band Edge Frequency 3 Lower Sidelobe Attenuation (78-82 MHz) Upper Sidelobe Attenuation (97.5-122.5 MHz) Triple Transit Suppression Group Delay Ripple (91.65 to 93.35 MHz) 2 System Source and Load Impedance Ambient Temperature Notes: Min Typ Max 17 93.35 90.50 92.50 18.2 0.5 91.57 93.52 90.63 94.42 90.1 94.9 50 50 50 75 50 25 22 0.7 91.65 94.50 95.5 90 - 89.5 45 45 40 - Units MHz dB dB p-p MHz MHz MHz MHz MHz MHz dB dB dB ns p-p ohm °C 1. Center Frequency: Fc = (Lower 15dB value + Upper 15dB value)/2. 2. A smoothing aperture of 150 kHz may be applied to this measurement. 3. Measured relative to the Insertion Loss Value. MAXIMUM RATINGS Parameter Storage Temperature Range Operating Temperature Range Input Power Level Min Max -40 10 - 85 70 13 Units ˚C ˚C dBm MATCHING CIRCUIT 11 5 Input 50 Ω Single ended Output 50 Ω Single ended 12 GND Typical Component Values: Ls1 = 400 nH 6 GND Ls2 = 420 nH Cp2 = 56 pF Notes: 1. Recommend ±2% tolerance matching components. Typical Inductor Q=40. 2. Values shown are for reference only and may change depending on board layout. Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0092CD02326S Rev A 22-Feb-2010 ECN 36650 Page 2 of 3 92.5 MHz SAW Filter 1.7 MHz Bandwidth Part Number SF0092CD02326S PACKAGE OUTLINE SUGGESTED FOOTPRINT Units: mm Tolerances are typically ±0.15 mm except where indicated. Pad Configuration: Input: 11 Input return: 12 Output: 5 Output return: 6 Case Ground: All other pads Package Material: Body: Al2O3 ceramic Lid: Kovar, Ni plated Terminations: Au plating 1 µm min, over a 1.3-8.9 µm Ni plating ISO 9001 Registered All specifications are believed to be accurate and reliable. However, Spectrum Microwave reserves the right to make changes without notice. © 2010 All rights reserved. Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0092CD02326S Rev A 22-Feb-2010 ECN 36650 Page 3 of 3