160 MHz SAW Filter 9.5 MHz Bandwidth Part Number: SF0160BA02299S DESCRIPTION • • • 160 MHz SAW bandpass filter with 9.5 MHz bandwidth. 13.3 x 6.5 mm SMP. RoHS compliant. TYPICAL PERFORMANCE 50. ns/" Horizontal: Vertical from top: S11 (130 to 190 MHz) Frequency : Relative Magnitude : Relative magnitude : Phase Linearity : Group Delay Deviation : 6 10 1 5 100 MHz/div dB/div dB/div deg/div ns/div S22 (130 to 190 MHz) Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0160BA02299S Rev A 11-Mar-2010 ECN 36650 Page 1 of 3 160 MHz SAW Filter 9.5 MHz Bandwidth Part Number: SF0160BA02299S SPECIFICATION Parameter Center Frequency ( Fc) 1 Insertion Loss at Fc 1 dB Passband Width Lower 1dB Frequency Upper 1dB Frequency Lower 30 dB Band Edge Upper 30 dB Band Edge Passband Amplitude Ripple 2 Passband Group Delay Ripple 2 Rejection (10 to 152 MHz) Rejection (168 to 250 MHz) Ambient Temperature Source / Load Impedance Temperature Coefficient of Frequency Substrate Material Notes: Min 159.7 9.5 164.7 152.0 45 45 - Typ Max 160.0 160.3 19 21 10.2 154.9 155.2 165.1 152.4 167.6 168.0 0.4 0.5 50 80 50 50 25 50 -94 YZ Lithium Niobate Units MHz dB MHz MHz MHz MHz dB p-p ns p-p dB dB ºC Ω ppm/ ºC 1. Fixed reference frequency. All bandwidths are centered at this frequency. 2. defined over Fc +/- 4 MHz. 3. Dependent on PC board layout. MAXIMUM RATINGS Parameter Storage Temperature Range Operating Temperature Range Input Power Level Min Max -40 20 85 30 10 Units ˚C ˚C dBm MATCHING CIRCUIT 12 6 Input 50 Ω Single-ended Output 50 Ω Single-ended 11 GND 5 GND Note: External matching components are not required. Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0160BA02299S Rev A 11-Mar-2010 ECN 36650 Page 2 of 3 160 MHz SAW Filter 9.5 MHz Bandwidth Part Number: SF0160BA02299S PACKAGE OUTLINE SUGGESTED FOOTPRINT Units: mm Package Material: Body: Al2O3 ceramic Lid: Kovar, Ni plated Terminations: Au plating 1 µm min, over a 1.3-8.9 µm Ni plating Tolerances are ±0.15 mm except for the overall length, width and pad dimensions, which are nominal values. Pad Configuration: Input: 12 Input return: 11 Output: 6 Output return: 5 Ground: 1,2,3,4,7,8,9,10 ISO 9001 Registered All specifications are believed to be accurate and reliable. However, Spectrum Microwave reserves the right to make changes without notice. © 2010 All rights reserved. Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0160BA02299S Rev A 11-Mar-2010 ECN 36650 Page 3 of 3