RH 1C

SANKEN ELECTRIC CO., LTD.
RH1C
1 Scope
The present specifications shall apply to a RH1C.
2 Outline
Type
Silicon Diode
Structure
Resin Molded
Applications
Flammability:UL94-V0(Equivalent)
High Frequency Rectification, etc.
3 Absolute maximum ratings
No.
Item
Symbol
Unit
Rating
Conditions
1
Transient Peak Reverse Voltage
VRSM
V
1000
2
Peak Reverse Voltage
VRM
V
1000
3
Average Forward Current
IF (AV)
A
0.6
Refer to derating curve in
Section 6
4
Peak Surge Forward Current
IFSM
A
35
10ms.
Half sine wave, one shot
5
I2t Limiting Value
I2 t
A2s
6.125
6
Junction Temperature
Tj
°C
-40 to +150
7
Storage Temperature
Tstg
°C
-40 to +150
1 ms ≤ t ≤ 10 ms
4 Electrical characteristics (Ta=25°C ,unless otherwise specified)
No.
Item
ymbol
Unit
Value
Conditions
1
Forward Voltage Drop
VF
V
1.3 max.
IF=0.6A
2
Reverse Leakage Current
IR
µA
5 max.
VR=VRM
3
Reverse Leakage Current Under
High Temperature
H・IR
µA
70 max.
Trr-1
µs
4.0 max.
Trr-2
µs
1.3 max.
4
5
Reverse Recovery Time
Thermal Resistance
130828
Rth (j-l) °C /W
15 max.
VR=VRM, Ta=100°C
IF=IRP=10mA
90% Recovery point, Tj=25°C
IF=100mA, IR=200mA
75% Recovery point ,Tj=25°C
Between Junction and Lead
1/3
61426-01
SANKEN ELECTRIC CO., LTD.
RH1C
5 VF test and test circuit
Percentage to rated forward current (%)
6 Derating
Derating to the ambient temperature.
Power loss generated by voltage is not taken into consideration.
100
80
60
40
20
0
0
20
40
60
80
100
120
140
160
Ambient temperature Ta (°C)
130828
2/3
61426-01
SANKEN ELECTRIC CO., LTD.
RH1C
7 Package information
7-1 Package type, physical dimensions and material
±0.05
※1
※3
φ0.78
φ4.0 ±0.2
62.5 ±0.7
7.2 ±0.2
※2
Dimensions in mm
*1 The allowance position of Body against the center of whole lead wire is 0.5mm (max.)
*2 The centric allowance of lead wire against center of physical body is 0.3mm (max.)
*3 The burr may exit up to 2mm from the body of lead
7-2 Appearance
The body shall be clean and shall not bear any stain, rust or flaw.
7-3 Marking
(1)
(2) (3)
(1)Polarity indication (Cathode Band)
(2) Marking Type number
RH1C
(3) Lot number 1
First digit : Last digit of year
Second digit : Month
From 1 to 9 for Jan. to Sep. O for Oct., N for Nov., and D for Dec.
Lot number 2 (ten days)
・
Top of the month
・・
Middle of month
・・・ End of month
The Type number and Lot number are to be marked in yellow.
The marking on the case of a part, which is printed in two positions, should be
legible in either of the two at least
130828
3/3
61426-01