EVB RT2856GQW-00 EN

RT2856GQW
Evaluation Board
your power partner.
6A, 18V, Synchronous Step-Down Converter
Purpose
The RT2856GQW is a current mode step-down converter with the input voltage range from 4.5V to 18V and
provides 6A outputcurrent. This document explains the function and use of the RT2856GQW evaluation board
(EVB), and provides information to enable operation, modification of the evaluation board and circuit to suit
individual requirements.
Table of Contents
Purpose ................................................................................................................................................................. 1
Introduction............................................................................................................................................................ 2
Key Performance Summary Table .......................................................................................................................... 2
Bench Test Setup Conditions ................................................................................................................................. 3
Schematic, Bill of Materials & Board Layout ........................................................................................................... 5
More Information.................................................................................................................................................... 8
Important Notice for Richtek Evaluation Board ....................................................................................................... 8
EVB_RT2856GQW-00
April
2016
1
http://www.richtek.com
RT2856GQW
Evaluation Board
your power partner.
Introduction
General Product Information
The RT2856GQW is a high efficiency, monolithic synchronous step-down DC/DC converter that can deliver up to 6A
output current from a 4.5V to 18V input supply. The RT2856GQW current-mode architecture with external
compensation allows the transient response to be optimized over a wide range of loads and output capacitors.
Cycle-by-cycle current limit provides protection against shorted outputs and soft-start eliminates input current surge
during startup. Fault condition protections include output under-voltage protection, output over-voltage protection,
and overtemperature protection. The low current shutdown mode provides output disconnection, enabling easy
power management in battery-powered systems.
Product Feature












Low RDS(ON) Power MOSFET Switches 26mΩ/19mΩ
Input Voltage Range : 4.5V to 18V
Adjustable Switching Frequency : 200kHz to 1.6MHz
Current-Mode Control
Synchronous to External Clock : 200kHz to 1.6MHz
Accurate Voltage Reference 0.8V±1%, Over 40°C to 85°C
Monotonic Start-Up into Pre-biased Outputs
Adjustable Soft-Start
Power Good Indicator
Under-Voltage and Over-Voltage Protection
Input Under-Voltage Lockout
RoHS Compliant and Halogen Free
Key Performance Summary Table
Key Features
Evaluation Board Number : PCB069_V1
Default Input Voltage
12V
Max Output Current
6A
Default Output Voltage
3.3V
Default Marking & Package Type
RT2856GQW, WQFN-14AL 3.5x3.5
Operation Frequency
Steady 200kHz to 1.6MHz
EVB_RT2856GQW-00
April
2016
2
http://www.richtek.com
RT2856GQW
Evaluation Board
your power partner.
Bench Test Setup Conditions
Headers Description and Placement
Please carefully inspect the EVB IC and external components, comparing them to the following Bill of Materials, to ensure that all components are
installed and undamaged. If any components are missing or damaged during transportation, please contact the distributor or send e-mail to
[email protected].
Test Points
The EVB is provided with the test points and pin names listed in the table below.
Test point/
Pin name
Signal
Comment (expected waveforms or voltage levels on test points)
Oscillator Resistor and
External Frequency
Synchronization Input
Oscillator Resistor and External Frequency Synchronization Input.
Connecting a resistor from this pin to GND sets the switching
frequency or connecting an external clock to this pin changes the
switching frequency.
GND
System Ground
System Ground. Provide the ground return path for the control
circuitry and low-side power MOSFET. The exposed pad must be
soldered to a large PCB and connected to GND for minimum power
dissipation.
PVIN
Power Input
Power Input. Supplies the power switches of the device.
VIN
Supply Voltage Input
Supply Voltage Input. Supplies the control circuitry and internal
reference of the device.
FB
Feedback Voltage Input
Feedback Voltage Input. This pin is used to set the desired output
voltage via an external resistive divider. The feedback reference
voltage is 0.8V typically.
COMP
Compensation Node
Compensation Node. The current comparator threshold increases
with this control voltage. Connect external compensation elements to
this pin to stabilize the control loop.
RT/SYNC
EVB_RT2856GQW-00
April
2016
3
http://www.richtek.com
RT2856GQW
Evaluation Board
your power partner.
Test point/
Pin name
Signal
Comment (expected waveforms or voltage levels on test points)
SS/TR
Soft-Start and Tracking
Control Input
Soft-Start and Tracking Control Input. Connect a capacitor from SS to
GND to set the soft-start period. The soft-start period can be used to
track and sequence when the external voltage on this pin overrides
the internal reference.
EN
Enable Control Input
Enable Control Input. Floating this pin or connecting this pin to logic
high can enable the device and connecting this pin to GND can
disable the device.
LX
Switch node test point
Switch Node. LX is the switching node that supplies power to the
output and connect the output LC filter from LX to the output load.
BOOT
Bootstrap Supply for
High-Side Gate Driver
Bootstrap Supply for High-Side Gate Driver. Connect a 100nF or
greater capacitor from LX to BOOT to power the high-side switch.
PGOOD
Power Good Indicator
Output
Power Good Indicator Output. This pin is an open-drain logic output
that is pulled to ground when the output voltage is lower or higher
than its specified threshold under the conditions of OVP, OTP,
dropout, EN shutdown, or during slow start.
Power-up & Measurement Procedure
1. Apply a 12V nominal input power supply (4.5V < VIN < 18V) to the VIN and GND terminals.
2. Set the jumper at J9 to connect terminals 1 and 2, connecting EN to VIN through resistor REN1, to enable
operation.
3. Verify the output voltage (approximately 3.3V) between VOUT and GND.
4. Connect an external load up to 6A to the VOUT and GND terminals and verify the output voltage and current.
Output Voltage Setting
Set the output voltage with the resistive divider (R1, R2) between VOUT and GND with the midpoint connected to
FB. The output is set by the following formula :
VOUT = VFB x (1 +
EVB_RT2856GQW-00
R1
)
R2
April
2016
4
http://www.richtek.com
RT2856GQW
Evaluation Board
your power partner.
Schematic, Bill of Materials & Board Layout
EVB Schematic Diagram
Bill of Materials
Reference
Qty
Part Number
Description
Package
Manufacture
U1
1
RT2856GQW
DC/DC Converter
WQFN-14AL
3.5x3.5
RICHTEK
R1
1
0603 75K0 1%
75kΩ
0603
WALSIN
R2
1
0603 24K0 1%
24kΩ
0603
WALSIN
RCOMP1
1
0603 2K40 1%
2.4kΩ
0603
WALSIN
RT, RPG1, REN1
3
0603 100K 1%
100kΩ
0603
WALSIN
C1, C2
2
UMK325BJ106MM-T
10µF/50V/X7R
1206
TAIYO
YUDEN
C4
1
GRM31CR71H475KA12L
4.7µF/50V/X7R
1206
muRata
C5, C6
2
C3225X5R1E226MT
22µF/25V/X7R
1210
TDK
CCOMP1
1
0603B822K500CT
8.2nF/50V/X7R
0603
WALSIN
CCOMP2
1
0603N181J500LT
180pF/50V/X7R
0603
WALSIN
CSS
1
0603B103K500
10nF/50V/X7R
0603
WALSIN
C3, C7, CBOOT
3
C1608X7R1H104KT000N
0.1µF/50V/X7R
0603
TDK
L1
1
3.7µH
CFF, C2F, CEN,
REN2, RTR1, RTR2,
RPG2, D2
8
N/A
EVB_RT2856GQW-00
April
2016
5
http://www.richtek.com
RT2856GQW
Evaluation Board
your power partner.
PCB Layout
Top View (1st layer)
PCB Layout—Inner Side (2nd Layer)
EVB_RT2856GQW-00
April
2016
6
http://www.richtek.com
RT2856GQW
Evaluation Board
your power partner.
PCB Layout—Inner Side (3rd Layer)
Bottom View (4th Layer)
EVB_RT2856GQW-00
April
2016
7
http://www.richtek.com
RT2856GQW
Evaluation Board
your power partner.
More Information
For more information, please find the related datasheet or application notes from Richtek website
http://www.richtek.com.
Important Notice for Richtek Evaluation Board
THIS DOCUMENT IS FOR REFERENCE ONLY, NOTHING CONTAINED IN THIS DOCUMENT SHALL BE CONSTRUED AS RICHTEK’S WARRANTY, EXPRESS
OR IMPLIED, UNDER CONTRACT, TORT OR STATUTORY, WITH RESPECT TO THE PRESENTATION HEREIN. IN NO EVENT SHALL RICHTEK BE LIABLE T O
BUYER OR USER FOR ANY AND ALL DAMAGES INCLUDING WITHOUT LIMITATION TO DIRECT, INDIRECT, SPECIAL, PUNITIVE OR CONSEQUENTIAL
DAMAGES.
EVB_RT2856GQW-00
April
2016
8
http://www.richtek.com