RT6236AHGQUF Evaluation Board your power partner. 6A, 18V, 650kHz, ACOT™ Synchronous Step-Down Converter Purpose The RT6236AH is a Advanced Constant On-Time (ACOT™) control architecture step-down converter with the input voltage range from 4.5V to 18V and provides 6A output current. This document explains the function and use of the RT6236AH evaluation board (EVB), and provides information to enable operation, modification of the evaluation board and circuit to suit individual requirements. Table of Contents Purpose ................................................................................................................................................................. 1 Introduction............................................................................................................................................................ 2 Key Performance Summary Table .......................................................................................................................... 2 Bench Test Setup Conditions ................................................................................................................................. 3 Schematic, Bill of Materials & Board Layout ........................................................................................................... 5 More Information.................................................................................................................................................... 8 Important Notice for Richtek Evaluation Board ....................................................................................................... 8 EVB_RT6236AHGQUF-00 December 2015 1 http://www.richtek.com RT6236AHGQUF Evaluation Board your power partner. Introduction General Product Information The RT6236AH is a high-performance 650kHz, 6A step-down regulator with internal power switches and synchronous rectifiers. It features quick transient response using its Advanced Constant On-Time (ACOT™) control architecture that provides stable operation with small ceramic output capacitors and without complicated external compensation, among other benefits. The input voltage range is from 4.5V to 18V and the output is adjustable from 0.7V to 8V. The proprietary ACOT™ control improves upon other fast response constant on-time architectures, achieving nearly constant switching frequency over line, load, and output voltage ranges. Since there is no internal clock, response to transients is nearly instantaneous and inductor current can ramp quickly to maintain output regulation without large bulk output capacitance. The RT6236AH is stable with and optimized for ceramic output capacitors. With internal 51mΩ switches and 18mΩ synchronous rectifiers, the RT6236AH displays excellent efficiency and good behavior across a range of applications, especially for low output voltages and low duty cycles. Cycle-by-cycle current limit provides protection against shorted outputs, input under-voltage lock-out, externally-adjustable soft-start, output under- and over-voltage protection, and thermal shutdown provide safe and smooth operation in all operating conditions. The RT6236AH is available in the UQFN-13JL 2x3 (FC) package, with exposed thermal pad. Product Feature Fast Transient Response Advanced Constant On-Time (ACOT™) Control 4.5V to 18V Input Voltage Range Adjustable Output Voltage from 0.7V to 8V 6A Output Current 51mΩ Internal High-Side N-MOSFET and 18mΩ Internal Low-Side N-MOSFET Steady 650kHz Switching Frequency Up to 95% Efficiency Optimized for All Ceramic Capacitors Externally-Adjustable, Pre-Biased Compatible Soft-Start Cycle-by-Cycle Current Limit Input Under-Voltage Lockout Output Over- and Under-Voltage Protection Power Good Output Thermal Shutdown Key Performance Summary Table Key Features Evaluation Board Number : PCB057_V1 Default Input Voltage 12V Max Output Current 6A Default Output Voltage 1.2V Default Marking & Package Type RT6236AHGQUF, UQFN-13JL 2x3 (FC) Operation Frequency Steady 650kHz at all loads EVB_RT6236AHGQUF-00 December 2015 2 http://www.richtek.com RT6236AHGQUF Evaluation Board your power partner. Bench Test Setup Conditions Headers Description and Placement Please carefully inspect the EVB IC and external components, comparing them to the following Bill of Materials, to ensure that all components are installed and undamaged. If any components are missing or damaged during transportation, please contact the distributor or send e-mail to [email protected] Test Points The EVB is provided with the test points and pin names listed in the table below. Test point/ Pin name Signal Comment (expected waveforms or voltage levels on test points) VIN Input voltage Power Input and Connected to High-Side MOSFET Drain. EN Enable test point High = Enable. Enable Control Input. GND Ground Ground. FB Converter Feedback Input Connect to output voltage feedback resistor divider. NC No Internal Connection No Internal Connection. SS Soft-Start Control A external capacitor should be connected to GND. PVCC Internal regulator output 5V Power Supply Output. A capacitor (typical 1µF) should be connected to GND. PGOOD Power good signal Open Drain Power Good Output. BOOT Bootstrap supply test point Bootstrap. This capacitor is needed to drive the power switch's gate above the supply voltage. It is connected between SW and BOOT pins to form a floating supply across the power switch driver. A 0.1µF capacitor is recommended for use. SW Switch node test point Connect this pin to an external L-C filter. EVB_RT6236AHGQUF-00 December 2015 3 http://www.richtek.com RT6236AHGQUF Evaluation Board your power partner. Power-up & Measurement Procedure 1. Apply a 12V nominal input power supply (4.5V < VIN < 18V) to the VIN and GND terminals. 2. Set the jumper at JP2 to connect terminals 2 and 3, connecting EN to VIN through resistor R5, to enable operation. 3. Verify the output voltage (approximately 1.2V) between VOUT and GND. 4. Connect an external load up to 5A to the VOUT and GND terminals and verify the output voltage and current. Output Voltage Setting Set the output voltage with the resistive divider (R2, R3) between VOUT and GND with the midpoint connected to FB. The output is set by the following formula : VOUT = VFB × (1 + R2 ) R3 EVB_RT6236AHGQUF-00 December 2015 4 http://www.richtek.com RT6236AHGQUF Evaluation Board your power partner. Schematic, Bill of Materials & Board Layout EVB Schematic Diagram Bill of Materials Reference Qty Package Manufacture C1, D1, L2 3 C3, C4 2 UMK325BJ106MM-T 10µF/50V/X5R C-1210 TAIYO YUDEN C5 1 C1608X5R1E105KT000E 1µF/25V/X5R C-0603 TDK C6, C8, C12 3 C1608X7R1E104KT000N 0.1µF/50V/X7R C-0603 TDK C7 1 C1608X7R1E104KT000N 3.9nF/50V/X7R C-0603 TDK C9, C10, C11 3 C3225X5R1E226MT 22µF/25V/X5R C-1210 TDK J1 1 VIN Golden pin J2, J6 2 GND Golden pin J3 1 VOUT Golden pin L1 1 NRS8030T1R0NJGJ 1.0µH R2 1 17k R-0603 R3 1 24k R-0603 R4, R5 2 100k R-0603 CP1 1 short U1 1 EVB_RT6236AHGQUF-00 Part Number Description NC RT6236AHGQUF December 2015 DC/DC Converter 5 TAIYO YUDEN UQFN-13JL 2x3 (FC) RICHTEK http://www.richtek.com RT6236AHGQUF Evaluation Board your power partner. PCB Layout Top View (1st layer) PCB Layout—Inner Side (2nd Layer) EVB_RT6236AHGQUF-00 December 2015 6 http://www.richtek.com RT6236AHGQUF Evaluation Board your power partner. PCB Layout—Inner Side (3rd Layer) Bottom View (4th Layer) EVB_RT6236AHGQUF-00 December 2015 7 http://www.richtek.com RT6236AHGQUF Evaluation Board your power partner. More Information For more information, please find the related datasheet or application notes from Richtek website http://www.richtek.com. Important Notice for Richtek Evaluation Board THIS DOCUMENT IS FOR REFERENCE ONLY, NOTHING CONTAINED IN THIS DOCUMENT SHALL BE CONSTRUED AS RICHTEK’S WARRANTY, EXPRESS OR IMPLIED, UNDER CONTRACT, TORT OR STATUTORY, WITH RESPECT TO THE PRESENTATION HEREIN. IN NO EVENT SHALL RICHTEK BE LIABLE TO BUYER OR USER FOR ANY AND ALL DAMAGES INCLUDING WITHOUT LIMITATION TO DIRECT, INDIRECT, SPECIAL, PUNITIVE OR CONSEQUENTIAL DAMAGES. EVB_RT6236AHGQUF-00 December 2015 8 http://www.richtek.com