RF & Microwave Components & Subsystems Quick Reference Guide, February 2016 Digital & Programmable Attenuators Programmable Attenuation, Phase Shifter & Switch Units COTS Subsystems High Reliability Attenuators Low PIM Attenuators & Terminations Medium & High Power Attenuators & Terminations Conduction Cooled (Flat-Pack) Attenuators & Terminations WEINSCHEL Innovative Design Solutions for Performance Driven Applications RoHS MMIC Digitally Switched Attenuator, Model 4205 Weinschel, a part of API Technologies Corp., offers a series of MMIC Digital Attenuators operate from 0.2 to 6 GHz in a variety of attenuation ranges up to 95.5 dB in that operate steps as low as 0.25. These units can be controlled using either parallel TTL or USB interfaces. o Ideal for Automated Test Equipment (ATE), WiMAX, 3G/4G, LTE, WiFi Fading Simulators, Engineering/Production Test Lab environments o Excellent Solid-state Repeatability & Performance o Uninterrupted RF when changing attenuation levels o Ruggedized Construction Model Number 4205-31.5 4205-63.5 4205-95.5 Frequency Range (GHz) Attenuation Range (dB) Step Size (dB) Insertion Loss, Max. (dB) Maximum SWR1 Connector Type Average Power 0.2-6.0 0-31.5 0-63.5 0-95.5 0.5 0.25 0.5 3.0 - 4.0* 4.5 - 6.0* 6.5 - 8.0* 1.50-1.70* 1.60-1.80* 1.60-2.10* SMA +23 dBm * Varies with frequency. 10 Control Configuration Units are supplied with both parallel TTL and USB 2.0 interfaces. The mode of operation is determined by the source of DC power to the unit. NOTE: Do not simultaneously connect DC power to the TTL connector while the USB is connected. USING USB CONFIGURATION: The USB interface is compatible with standard USB 2.0 interfaces. In USB mode, DC power to the attenuator is provided by the host USB connection. The attenuator operates as a USB CDC device and accepts simple ASCII text commands. This allows the unit to be controlled from any system capable of sending data via a standard COM port-style interface. -10 0.5 dB Attenuation (dB) USING TTL CONTROL: Each unit is supplied with a mating 10 pin connector (Amp 746285-1). Refer to Physical Dimensions for mating connector pin/wiring details. Two pins are specified for supply voltage and ground. The remaining pins will accept TTL control signals to activate or de-activate a particular attenuation cell. A TTL high will energize a cell to the high attenuation state, whereas a TTL low will maintain a cell in its zero attenuation state. 0 -20 1 dB 2 dB 4 dB -30 8 dB 16 dB -40 32 dB 64 dB -50 -60 -70 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 Frequency (GHz) Attenuation Performance Plot Control Software Included Weinschel LabVIEWTM based USB Control Center Software can be used in conjunction with the operation of this Series of digital attenuators. The control center software will allow the user to setup, control and perform test and measurements using these digital attenuators over a standard USB 2.0 communication interface. 2 © API Technologies, Inc. Proprietary Information | weinschel.apitech.com | [email protected] | 301-846-9222 , 800-638-2048 WEINSCHEL Physical Dimensions 2X 4-40 UNC-2B 63.5 [2.50] 43.18 [1.700] 9.5 [.38] 8.4 [.33] 10.2 [.40] 9.5 [.38] 5.6 [.22] 29.21 [1.150] 4.1[.16] 9.0 [.36] 4X 2-56 UNC-2B 43.18 [1.700] 4.1[.16] SEE VIEW A PIN 1 17.1 [.68] 10.2 [.40] PIN 2 WEINSCHEL CAGE: 93459 MODEL: 4205-95.5 SERNO: XXXX 0.2-6GHz 0-95.5 dB / 0.5dB 47.5 [1.87] 59.18 [2.330] 63.5 [2.50] 4205 SERIES 10.9 [.43] 9.0 [.36] 4X 2-56 UNC-2B 2X 4-40 UNC-2B 4.1[.16] 6.6 [.26] 59.18 [2.330] 44.3 [1.75] 10.9 [.43] 2.2 [.09] 2.2 [.09] 4.1[.16] PIN 1 13.8 [.54] 17.1 [.68] 29.21 [1.150] 6.6 [.26] PIN 5 VIEW A SCALE 4 : 1 NOTE: All dimensions are given in mm (inches). Dual Band 4x4 Butler Matrix, Model 8401 B1 B3 Output B2 B4 SMA (F), 4 Pls 0° -90° -90° 0° -45° Fixed phase shift 0° -90° -90° 0° 0° -90° -90° 0° o Ideal for your Lab Testing/Calibration Setups and subsystem applications o Operating Frequencies: 2.4 to 6.0 GHz o Compact Module Design with SMA female connectors -45° o Inputs are isolated from each other. o VSWR: 1.5:1 Typical, 1.6:1 Maximum o Output Phase Accuracy: ±30° o Insertion Loss: 8 dB Typical, 10 dB Maximum 0° -90° -90° 0° o Isolation: 18 dB Typical, 15 dB Minimum o Operating Temperature Range: -20 °C to +70 °C o Custom and other configurations available. SMA (F), 4 Pls A1 A2 Input A3 A4 3 © API Technologies, Inc. Proprietary Information | weinschel.apitech.com | [email protected] | 301-846-9222 , 800-638-2048 Innovative Design Solutions for Performance Driven Applications RoHS Digital Switch, Model 4284 This new Weinschel series operates over the 0.1 to 6 GHz frequency range. This SP4T absorptive switch can be controlled using either parallel TTL or USB interfaces. o Ideal for Automated Test Equipment (ATE), WiMAX, LTE, WiFi, 3G/4G Fading Simulators, Engineering/ Production Test Lab environments o Excellent Solid-state Repeatability & Performance o Uninterrupted RF when changing switch positions. o Unselected ports are internally terminated with a 50 ohm load. o Switching Speed: 1 μsec maximum (TTL) 5 msec typical (USB) o Control Software Included o Ruggedized Construction Model Number Switch Type Frequency Range (GHz) 4284 SP4T 0.1-6.0 Isolation minimum (dB) Typ. Max. 0.1 - 3.0: 3.0 - 5.0: 5.0 - 6.0: 60 48 38 55 42 30 Insertion Loss, Min. (dB) Maximum SWR1 3.0-4.5 1.50:1 Connector Average Type Power (Watts) SMA 1 USING USB CONFIGURATION: The USB interface is compatible with standard USB 2.0 interfaces. In USB mode, DC power to the switch is provided by the host USB connection. The switch operates as a USB CDC device and accepts simple ASCII text commands. This allows the unit to be controlled from any system capable of sending data via a standard COM port-style interface. Control Configuration Units are supplied with both parallel-TTL and USB 2.0 interfaces. The mode of operation is determined by the source of DC power to the unit. NOTE: Do not simultaneously connect DC power to the TTL connector while the USB is connected. USING TTL CONTROL: Each unit is supplied with a mating 10 pin connector (Amp 746285-1). Refer to Physical Dimensions for mating connector pin/wiring details. Two pins are specified for supply voltage and ground. The remaining pins will accept TTL control signals to activate or de-activate a particular switch position. Control Software Included Weinschel LabVIEWTM based USB Control Center Software (UCS) can also be used in the operation of this series of digital switches. The UCS will allow the user to setup, control and perform test and measurements using these digital switches over a standard USB 2.0 communication interface. Physical Dimensions PIN 1 PIN 5 2X 4-40 UNC - 2B X 4.1[.16 DEEP] DETAIL A SCALE 4 : 1 14.8 [.58] 82.8 [3.26] 8.9 [.35] 9.5 [.38] 6.1 [.24] 50.8 [2.00] 16.0 [.63] SEE DETAIL A PIN 1 9.7 [.38] 63.5 [2.50] PIN 2 WEINSCHEL 91.7 [3.61] 98.0 [3.86] 82.0 [3.23] 93.3 [3.67] 78.9 [3.11] 53.4 [2.10] 15.1 [.59] 53.4 [2.10] 15.1 [.59] 8.3 [.33] 3.2 [.13] 41.4 [1.63] 7.1 [.28] 4X 2-56 UNC - 2B X 4.1[.16 DEEP] 4X 2-56 UNC - 2B X 4.1[.16 DEEP] 2.4 [.09] 50.8 [2.00] 16.0 [.63] 9.5 [.38] NOTE: All dimensions are given in mm (inches). 4 © API Technologies, Inc. Proprietary Information | weinschel.apitech.com | [email protected] | 301-846-9222 , 800-638-2048 WEINSCHEL 75 Ω Programmable Attenuators Model 3456 Series 75 Ω Programmable Step Attenuators are designed for use in automatic test equipment and OEM systems operating in the DC to 3 GHz frequency range. Each cell contains a double-pole, double-throw relay that provides a zero path or attenuated path for the RF signal. o Cost Effective design for Wireless/Cable Applications o Custom Configurations including bus controlled attenuator subsystems Model Number 3456-63 Frequency Range (GHz) DC-3.0 Attenuation Range (dB) 0-63 Step Size (dB) 1 Insertion Maximum Loss, Max. SWR (dB) 2.10-3.30* 1.45-1.50* Connector Type SMA Average Power (Watts) 1 Peak Power (Watts) 50 * Varies with frequency. 6 GHz Programmable Attenuators & Phase Shifters Ideal for Wireless/Test Applications o Higher Frequency range to 6 GHz o Selection of Attenuation Ranges & Step Sizes o High Quality Construction & Connectors o Optional TTL Interface for easy Subsystem Integration o Special Configurations Available Upon Request Programmable Attenuators Model Number 3404-15 3404-55 3404-70 3404T-15 3404T-55 3404T-70 3409-127 Frequency Range (GHz) DC-6.0 DC-6.0 DC-6.0 Attenuation Range (dB) 0-15 0-55 0-70 0-15 0-55 0-70 0-127 Step Size (dB) 1 5 10 1 5 10 1 Insertion Maximum Loss, Max. SWR (dB) 2.60 1.30-1.45* 2.60 2.60 2.60 1.30-1.45* 2.60 2.60 3.8-5.8* 1.40-1.55* Connector Type SMA Average Power (Watts) 1 Peak Power (Watts) 50 SMA 1 50 SMA 1 50 Programmable Phase Shifters Model Number 984-1 Frequency Range (GHz) Phase Shift Range (°) Insertion Loss dB Maximum (Any Phase State) Insertion Loss Variation Insertion Phase (°) Maximum SWR1 Power Rating (Watts) Connector Type DC-6.0 From 0° @ DC to 630° in 10° steps @ 6 GHz (Normally linear with frequency) 2.5 @ 3 GHz 4.3 @ 6 GHz + 0.5 dB Typical 2,700° Typical @ 6 GHz 1.50-1.60* 1 SMA * Varies with frequency. 5 © API Technologies, Inc. Proprietary Information | weinschel.apitech.com | [email protected] | 301-846-9222 , 800-638-2048 Innovative Design Solutions for Performance Driven Applications RoHS Programmable Attenuator Units, Models 8320, 8321 & 8331 Model 8320 The 8320 series are single or up to 4 channel configurations housed in half rack enclosures. The 8321 series are multi-channel configurations housed in 19 inch enclosures and can be configured for up to 12 attenuation channels. Both series can be configured for front or rear and through options. ATTEN OUTPUT ATTEN INPUT 1 API Weinschel also provides custom subsystems where a variety of test configurations can be incorporated within a single unit. Contact us with your specialized needs. 2 Basic Model Number Attenuator Number of Designator Channels(1) (see page 7) (01 to 04) Example: 8320-M3-02-TS GPIB (IEEE-488) Option Blank = Not Installed G = Installed Connector Type N: N (2) S: SMA (3) K: 2.92 mm (4) F: F-Type (5) Connector Location (1) F = Front R = Rear T = Front - Rear 8331 - XX - XX - X X Basic Model Number Attenuator Number of Designator Channels (1) (see below) (01 to 12) Example: 8331-M3-09-TS 6 Attenuator # 2 2 Attenuator # 3 3 Control 3 Control Attenuator # 11 11 Attenuator # 12 12 Control 12 Control Control USB, RS-232, Ethernet PSU Controller Simplified 12 Channel Block Diagram Model Number Configuration Matrix 8320 - XX - XX - X X G 1 Control 11 Model 8331 Series offers a lower cost solution for automated bench test and subsystem applications. Most 8331 Series are multi-channel configurations where RF signal is routed through either the front or rear mounted ports. This series can be configured for up to 12 independent channels of attenuation and can be controlled via ethernet, USB and Serial communications interfaces. Attenuator # 1 BACK PANEL Provides a flexible, easy to program, low cost solution for your bench test/ calibration setups and subsystem applications. This Series of Programmable Attenuator Units represent a new streamlined approach in programmable attenuation for bench test and subsystem applications. Standard 8320 and 8321 Series designs house and control various Weinschel Programmable Attenuator Models (3200-XE, 3400, 150T, and 4200 Series) via front panel controls, ethernet, USB and Serial communications interfaces. A GPIB (IEEE-488) interface is also available as an option. Model 8331 FRONT PANEL Model 8321 1. 8320: Up to 4 channels total except for up to 2 channels for option F & R (Front or Rear), up to 2 channels for option C & D (150T & 152T Series), 1 channel only for option C7 & D5, up to 2 channels for option E3 8321 & 8331: Up to 12 channels total except for up to 6 channels for option F & R (Front or Rear), up to 10 channels for option C & D (150T & 152T Series), up to 5 channels for option C7 & D5, up to 6 channels for option E3 2. Not available for option D, E & F (152T, 156 & 3456 Series) 3. Not available for option E & F (156 & 3456 Series) 4. Only for option E (156 Series) Connector Type N: N (2) S: SMA (3) K: 2.92 mm (4) F: F-Type (5) Connector Location (1) F = Front R = Rear T = Front - Rear 5. Only for option F (3456 Series) Control Software Included Weinschel LabVIEWTM based Attenuator Control Center Software (ACCS) can be used in conjunction with the operation of the this series of programmable attenuator units and allows the user to setup, control and perform test and measurements over standard communication interfaces such as USB, Ethernet or RS-232. © API Technologies, Inc. Proprietary Information | weinschel.apitech.com | [email protected] | 301-846-9222 , 800-638-2048 WEINSCHEL Attenuator Designations & Specifications Electro-mechanical Frequency Range Attenuator Designation DC-3 GHz A DC-6 GHz B DC-18 GHz C DC-26.5 GHz D DC-40 GHz New E DC-3 GHz (75 Ω) New F Attenuator Model Range (dB) Step Size (dB) Insertion Loss (maximum) VSWR RoHS (maximum) 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 1 2 3 4 5 6 7 1 2 3 4 5 1 2 3 3205-1E 3205-2E 3205-3E 3201-1E 3206-1E 3200-1E 3200-2E 3209-1E 3404-15 3404-55 3404-70 3406-55 3408-55.75 3408-103 3409-127 150T-70 150T-15 150T-75 150T-110 150T-31 150T-62 150T-15 & 150T-110 152AT-70 152T-15 152T-75 152T-90 152T-90 & 152T-15 156-11 156-90 156-11 & 156-90 70 55 1.5 31 63 127 63.75 64.5 15 55 70 55 55.75 103 127 70 15 75 110 31 62 125 70 15 75 90 105 11 90 101 10 5 0.1 1 1 1 0.25 0.1 1 5 10 1 0.25 1 1 10 1 5 10 1 2 1 10 1 5 10 1 1 10 1 3.75 3.75 3.75 4.00 4.25 5.25 5.25 6.50 3.50 3.50 3.50 4.50 6.00 6.00 6.50 3.25 3.50 3.50 3.50 3.75 3.75 5.50 4.75 5.00 5.00 5.00 8.00 5.00 5.00 7.00 dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.5 1.55 1.55 1.55 1.55 1.55 1.55 1.55 1.75 1.95 1.95 1.95 1.95 1.95 1.95 1.95 1.95 1.95 1.95 1.95 2.00 2.00 2.00 1 3456-63 63 1 4.50 dB 1.70 1 2 3 1 2 1 2 3 1 2 3 4226-63 4228-63.75 4228-103 4238-63.75 4238-103 4246-63 4248-63.75 4248-103 4205-31.5 4205-63.5 4205-95.5 63 63.75 103 63.75 103 63 63.75 103 31.5 63.5 95.5 1 0.25 1 0.25 1 1 0.25 1 0.5 0.5 0.5 4.75 dB 6.00 dB 6.00 dB 10.00 dB 10.00 dB 11.00 dB 14.00 dB 14.00 dB 4.00 dB 6.00 dB 8.50 dB 1.6 1.6 1.6 1.75 1.75 2.0 2.0 2.0 1.8 1.8 2.0 Solid-state 0.8 to 2.5/3 GHz J 0.01 to 2.5 GHz K 0.01 to 2.5 GHz L 0.2 to 6 GHz M RoHS compliance dependent on attenuator installed. Some attenuators are NOT compliant. 7 © API Technologies, Inc. Proprietary Information | weinschel.apitech.com | [email protected] | 301-846-9222 , 800-638-2048 Innovative Design Solutions for Performance Driven Applications API Weinschel, Inc. API Weinschel, Inc. Physical Dimensions Standard 19 in Rack Unit up to 12 channels: 8.74 [.34] 37.97 [1.50] TYPICAL FRONT AND REAR 76.20 [3.000] DIM “A” 5.97 [.24] 304.80 [12.00] 13.21 [.52] CHAN 2 B CHAN 3 B CHAN 4 B CHAN 6 B 2 CHAN 7 B CHAN 8 A CHAN 10 B CHAN 12 B MADE IN USA API Weinschel, Inc. 8321 SERIES CHAN 12 A CAGE CODE 93459 CHAN 11 A CHAN 11 B 2 4X HOLE PLUG MODEL: SERNO: CHAN 10 A 2 4X HOLE PLUG .25 X .40 LONG SLOT, 4X [6.35] [10.16] 8X CONNECTOR, TYPE N FEMALE CHAN 9 B CONNECTOR, PER IEEE 488.2 PROTOCOL CHAN 9 A 19.3 [.76] TYP FRONT AND REAR CONNECTOR, ETHERNET RJ45 CHAN 8 B 425.20 [16.74] GPIB 8X CONNECTOR, TYPE N FEMALE CHAN 7 A 11X 31.75 = 349.25 [1.250] [13.75] TYPICAL FRONT AND REAR LAN 2 CHAN 6 A 482.60 [19.00] LINK CHAN 5 A CONNECTOR, USB, MINI B ACT USB CHAN 4 A 465.12 [18.312] CONNECTOR, 9 PIN D MALE, RS232 CHAN 3 A 31.75 [1.250] TYPICAL FRONT AND REAR SERIAL CHAN 2 A POWER INPUT 115/230 VAC 0.5A 50/60Hz CHAN 5 B CHAN 1 A 28.70 [1.13] TYP FRONT AND REAR CHAN 1 B POWER SWITCH 1.27 [.05] 88.14 [3.47] Connector Type N SMA, SMK (2.92mm) F DIM A 14.7 (0.60) 5.21 (0.21) 15.5 (0.61) NOTE: 1. All dimensions are given in mm (inches). 2. Connectors and hole plugs are installed as required and determined by number of channel in unit. 2 channel shown for Model 8320 and 8 channel unit shown for 8321. 3. Connector location (Front/Rear) may vary depending on Model ordered. 8 © API Technologies, Inc. Proprietary Information | weinschel.apitech.com | [email protected] | 301-846-9222 , 800-638-2048 WEINSCHEL 8304-5, RF Switch Subsystem (Simplifies Mobile Radio Testing) RoHS Features o o o o DC - 2 GHz Frequency Range 50 Ohm Impedance 5 Radio Interfaces RS-232 Control Weinschel Model 8304-5 RF Switching System is part of an automated test set-up for various types of commercial and military radios. The difference in the test set up and configuration between different types of radios will be the control interconnect cables used. The block diagram below shows the RF Switch Subsystem which is designed to control and test up to 5 radios at a time. This subsystem acts as an interface and is connected to a Model 3901 Digital Radio Test Set (customer provided) to enable the total system to automatically connect signals to 5 radios. The RF signals are routed through an internal electro-mechanical switch. The Digital Radio Test Set is used as the controller, signal stimulus and measurement instrument. All switching selection occurs via the USB control port located on the rear panel of the Model 8304-5. The RF Switching System is an RF subsystem that utilizes an internal Micro Computer to provide control of the switches and relays via the USB to serial interface. Simplified Block Diagram Physical Dimensions: PER IEC320 115-230 VAC 1.5A 50/60Hz 16.13 [.64] 133.35 [5.25] 517.53 [20.38] 10.41 [.41] FUSE 30 - 512 MHz 225 - 2000 RADIO 2 30 - 512 MHz 225 - 2000 RADIO 1 COM 3 COM 2 COM 1 ~ 50-60 Hz 115-230V, 50W FUSE: F1.5, 250V ADF 1 30 - 512 MHz 225 - 2000 RADIO 3 1/4-20, GND STUD CONNECTOR, USB B, MALE CONNECTOR, 9 PIN D, MALE 5X CONNECTOR, TYPE N, FEMALE BUS STATUS STATUS LED, 3X COM7 - PWR SUPPLY COM6 - SPARE MADE IN USA CONNECTOR, CIRCULAR DIN, 8 PIN, FEMALE CAGE CODE 93459 TX RX RF SWITCHING UNIT 5 CHANNEL MODEL 6904-5 PWR API Weinschel, Inc. CONNECTOR, BNC FEMALE, 2X MODEL: SERNO: MIC / ACC COM 4 FCTN GEN / DEMOD COM 5 AUDIO IN 30 - 512 MHz 225 - 2000 RADIO 5 30 - 512 MHz 225 - 2000 RADIO 4 T/R ADF 5 ADF 4 CONNECTOR, 9 PIN D, MALE, 2X USB ADF 2 CONNECTOR, TNC, FEMALE, 10X 380.65 [14.99] ADF 3 365.13 [14.38] CONNECTOR, CIRCULAR, U-183/U, 5X NOTE: LABEL, POWER INPUT POWER SWITCH LABEL, MODEL IDENTIFICATION All dimensions are given in mm (inches) and are maximum, unless otherwise specified. EXPORT CONTROL: This product is controlled for export under the International Traffic in Arms Regulations (ITAR). A license from the U.S. Department of State is required prior to the export of this product from the United States. EXPORT WARNING: Military and space products are controlled for export under the International Traffic in Arms Regulations (ITAR) and may not be sold or proposed or offered for sale to certain countries. (See ITAR 126.1 for complete information.) 9 © API Technologies, Inc. Proprietary Information | weinschel.apitech.com | [email protected] | 301-846-9222 , 800-638-2048 Innovative Design Solutions for Performance Driven Applications RoHS Programmable Attenuation Profile Simulator Unit, Model 8334 Features Applications o Programmable attenuation update rates from 50 μsec. per point to 1 second per point in 50 μsec. intervals o External TTL trigger (with programmable polarity) allows for synchronization with other external hardware o Various TTL status outputs (Running, Programmable Sync, and Interval Update) for monitoring a profile Applications for the 8334 Series include: o Simulate path loss on each channel or mobility scenarios between a handset and multiple base stations o Create arbitrary, synchronous attenuation profiles with timing skews of <10 nsec. between channels to replicate precision fading and handover scenarios o Generate coherent, multi-channel pulsed RF outputs for a given attenuation level o Supplied with industry standard communication interfaces: - RS-232 (Serial) - Ethernet Control (10/100 BaseT) - USB 2.0 o Rack Configurable: Rack ears are supplied RF In/Out RF In/Out Description Channel 8 Port A Attenuator 8 Channel 8 Port B Weinschel 8334 Series of Attenuation Profile Simulators provide multi-channel high-speed attenuation control with synchronous output update capability. The unit allows for programming of up to 128K (131072) attenuation data points per attenuator and sweeping through those data points at user-programmable intervals from 50 μsec to 1 sec per point. The system provides for non-volatile storage of up to four data point tables which may be later recalled under user control. Status and control TTL signals are available for external monitoring and sweep control via a rear-panel DE9 connector. Channel 7 Port A Attenuator 7 Channel 7 Port B Channel 6 Port A Attenuator 6 Channel 6 Port B Channel 5 Port A Attenuator 5 Channel 5 Port B Channel 4 Port A Attenuator 4 Channel 4 Port B Channel 3 Port A Attenuator 3 Channel 3 Port B Channel 2 Port A Attenuator 2 Channel 2 Port B Channel 1 Port A Attenuator 1 Channel 1 Port B The 8334 Series are multi-channel configurations housed in 19 inch enclosures and can be configured for up to 8 attenuation simulator channels with front, rear or through (front to rear) RF signal routing. Weinschel also provides custom subsystems where a variety of test configurations can be incorporated within a single unit. Contact us with your specialized needs. To all Attenuators, 0-95.5 dB/0.5 dB (8max.) 64-BIT OUTPUT REGISTER/LATCH TABLE DATA MEMORY (1 MB SRAM) INTERVAL UPDATE TABLE STORAGE (4 MB FLASH) High-Speed Attenuation Control Processor (HSAC) STATUS LEDs AUX TTL STATUS EXT TRIG SYNC INTERVAL UPDATE RUN Internal Communications Link RS -232 Serial Main Communications Processor USB 10/100 Ethernet Simplified 8 Channel Block Diagram 10 © API Technologies, Inc. Proprietary Information | weinschel.apitech.com | [email protected] | 301-846-9222 , 800-638-2048 WEINSCHEL Physical Dimensions Standard 19 in Rack Unit up to 8 channels: 8.74 [.34] 28.70 [1.13] TYP FRONT AND REAR 76.20 [3.000] 304.80 [12.00] 13.21 [.52] 5.97 [.24] 13.21 [.52] POWER SWITCH POWER 2 6X CONNECTOR, TYPE N FEMALE CHAN 2 B CHAN 3 B CONNECTOR, ETHERNET RJ45 AUX CHAN 5 A CHAN 8 B MADE IN USA CAGE CODE 93459 API Weinschel, Inc. 8334 SERIES CHAN 8 A .25 X .40 LONG SLOT, 4X [6.35] [10.16] 2 2X HOLE PLUG MODEL: SERNO: CHAN 7 A CHAN 7 B CHAN 6 B 2 2X HOLE PLUG CHAN 6 A 19.30 [.76] TYP FRONT AND REAR CHAN 5 B CHAN 4 A 7X 31.75 =222.25 [1.250] [8.750] TYP FRONT AND REAR 2 6X CONNECTOR, TYPE N FEMALE CHAN 4 B CHAN 3 A 425.20 [16.74] CHAN 1 B USB CHAN 2 A 482.60 [19.00] ACT CONNECTOR, USB, MINI B (OPTION NOT AVAILABLE) CHAN 1 A 465.12 [18.312] CONNECTOR, 9 PIN D MALE, RS232 LAN 31.75 [1.250] TYP FRONT AND REAR SERIAL POWER INPUT 115/230 VAC 0.5A 50/60Hz LNK STAT TRIG ARM RUN 164.97 [6.50] TYP FRONT AND REAR 1.27 [.05] 88.14 [3.47] NOTE: 1. All dimensions are given in mm (inches). 2. Connectors and hole plugs are installed as required and determined by number of channel in unit. Six channel unit shown. 3. Connector location (Front/Rear) may vary depending on Model ordered. Model Number Configuration Matrix 8334 - M3 - XX - X N Basic Model Number Attenuator Designator Number of Channels (01 to 08) Example: 8334-M3-08-TN Connector Type N = N Female * up to 6 Channel units available for option F & R. Connector Location F = Front * R = Rear * T = Thru Solid-state (Only) Frequency Attenuator Attenuator Model Range Designation 0.2 to 6 GHz M 3 4205-95.5 Range (dB) 95.5 Step Size (dB) 0.5 Insertion Loss (maximum) 8.50 dB VSWR (maximum) 2.0 RoHS RoHS compliance dependent on attenuator installed. Some attenuators are NOT compliant. 11 © API Technologies, Inc. Proprietary Information | weinschel.apitech.com | [email protected] | 301-846-9222 , 800-638-2048 Innovative Design Solutions for Performance Driven Applications Model 8351, High Power Fixed Attenuator Unit Internal Temperature Monitoring/Reporting RoHS The Weinschel Model 8351 Series of High Power Fixed Attenuator Units offers a compact, rack mount solution to monitor up to 6 channels of Weinschel High Power Fixed Attenuators for bench testing, subsystem, and system applications. The standard Model 8351 Series designs operate over the DC to 6 GHz frequency range, with power handling up to 400 watts C.W. The Model 8351 Series features Weinschel Conduction Cooled (flat pack) Attenuators, mounted on an internal heat sink and are cooled with 2 automatic, variable speed fans based upon internal temperature monitoring. This series can be configured with front mounted Type N connectors (IN/OUT) for up to 3 channels, or front to rear Type N connectors for up to 6 Channels. o Sensors indicate the maximum allowed input power into each channel o Thermal monitoring of each channel reported through USB 2.0 and Serial communication interface o Multi-Channel fixed attenuation paths (up to 6 channels) Extremely low VSWR Frequency Range from DC to 6 GHz minimum Power Handling up to 400 watts C.W. per channel Standard communication interfaces: - USB 2.0 - RS-232 (Serial) o 3 light LED Front Panel status indicator o LabView based Attenuator Monitor Software included o Rack Configurable – Rack mount ears are supplied for a standard 19” rack configuration ATTEN OUTPUT ATTEN INPUT 1 Attenuator # 1 1 Attenuator # 2 2 Attenuator # 3 3 Attenuator # 4 4 Attenuator # 5 5 Attenuator # 6 6 Monitoring 2 Monitoring FRONT PANEL o o o o LabVIEWTM based Attenuator Monitor Software is included for the monitoring of the internal power sensors via USB 2.0 or RS-232 communication interfaces. Weinschel also provides custom configurations where multiple dB values / high power requirements can be incorporated within a single unit. Contact us with your specialized needs. 3 Monitoring 4 BACK PANEL Features Monitoring Applications 5 Applications for the 8334 Series include: o o o o Monitoring 4G LTE Base Station Testing Distributed Antenna Systems (DAS) Military Radio Testing High Power Amplifier Testing 6 Monitoring Monitoring USB / RS-232 Model Number Configuration Matrix PSU 8351 - A XX - X - X N Basic Attenuator Model Designator Number (see below) Controller Simplified 6 Channel Block Diagram Connector Type N = N Female Attenuator dB Value Example: 8351-A10-6-TN Number of Channels (1 to 6)* Connector Location F = Front (IN/OUT)* T = Front (IN) to Rear (OUT) * Up to 3 Channels for Option F (Front) 12 © API Technologies, Inc. Proprietary Information | weinschel.apitech.com | [email protected] | 301-846-9222 , 800-638-2048 WEINSCHEL Physical Dimensions 76.20 [3.000] 6.0 [.24] 6.35 X 10.2 [.250 X .40] 4X SLOT 9.7 [.38] 8.7 [.34] 13.2 [.52] 31.8 [1.25] PWR SW 4 PWR INPUT 115/230 VAC ATTEN OUTPUT 1 CAUTION 250 WATTS MAX PER ATTEN HIGH OPERATING SURFACE TEMP WEINSCHEL 19.7 [.78] 72.7 [2.86] 63.5 [2.50] 5 4 AIR DIRECTION OUT 55.9 [2.20] 322.3 [12.69] 1 CONNECTOR USB MINI B 354.1 [13.94] 5 465.1 [18.31] CONNECTOR 9 PIN D MALE RS232 USB 385.8 [15.19] 5X 55.9 [2.20] =[279.4] 11.00 SERIAL ATTEN INPUT 482.6 [19.00] 2 425.2 [16.74] AIR DIRECTION OUT 2 6 STATUS 8351 SERIES CAUTION 50 WATTS MAX PER ATTEN HIGH OPERATING SURFACE TEMP 3 ATTEN OUTPUT 6 3 6X CONNECTOR TYPE N, FEMALE 2 6X CONNECTOR TYPE N, FEMALE 2 1.3 [.05] 29.8 [1.18] 304.8 [12.00] 88.1 [3.47] 61.0 [2.40] NOTE: 1. All dimensions are given in mm (inches). 2. Connectors and hole plugs are installed as required and are determined by the number of channels in the unit. 6 channel shown. 3. Connector location (Front/Rear) may vary depending upon the Model ordered. Attenuator Designations & Specifications Channel Specifications Frequency Range DC-6 GHz DC-6 GHz DC-6 GHz Attenuator Attenuator Designation Model Attenuation (dB) Deviation (+dB) VSWR IN (maximum) 2.5 GHz 2.5-6 GHz VSWR Maximum OUT Power** RoHS (maximum) (Watt) 10 268-10-33 10 1 1.1 1.15 1.35 100 20 268-20-33 20 1 1.1 1.15 1.35 100 30 268-30-33 30 1 1.1 1.15 1.35 100 40 268-40-33 40 1 1.1 1.15 1.35 100 10 257-10-33 10 1 1.1 1.15 1.35 250 20 257-20-33 20 1 1.1 1.15 1.35 250 30 257-30-33 30 1 1.1 1.15 1.35 250 40 257-40-33 40 1 1.1 1.15 1.35 250 10 258-10-33 10 1.50 1.1 1.15 1.35 400 20 258-20-33 20 1.50 1.1 1.15 1.35 400 30 258-30-33 30 1.75 1.1 1.15 1.35 400 40 258-40-33 40 1.75 1.1 1.15 1.35 400 A B C RoHS compliance dependent upon attenuator installed. ** Maximum Input Power is derated in certain cases, depending upon the ambient temperature and the number of active channels. 13 © API Technologies, Inc. Proprietary Information | weinschel.apitech.com | [email protected] | 301-846-9222 , 800-638-2048 Innovative Design Solutions for Performance Driven Applications RoHS Programmable Phase Shifter Units, Models 8420 & 8421 Model 8421 Model 8420 Front Panel Control & Indicators Weinschel Model 8420 and 8421 Series represent a new streamlined approach in signal phase shift control for bench test and subsystem applications. This series is designed to house and control the new Weinschel Programmable Phase Shifter series via front panel controls, ethernet, USB and Serial communications interfaces. A GPIB (IEEE-488) interface is also available as an option. OUTPUT INPUT 1 Ø 1 Ø 2 Ø 3 Ø 11 Ø 12 Control 2 Weinschel also provides custom subsystems where a variety of test configurations can be incorporated within a single unit. Contact us with your specialized needs. 3 Control 11 Control Software Included BACK PANEL Control FRONT PANEL The 8420 series are single or dual channel configurations housed in half rack enclosures. The 8421 series are multi-channel configurations housed in 19 inch enclosures and can be configured for up to 12 channels. Both series can be configured for front or rear and through (front to rear) is only available for 8421 Series. To Controller Control 12 Weinschel’s LabVIEWTM based Control Center Software can be used in conjunction with the operation of the this series of programmable phase shifter units and allows the user to setup, control and perform test and measurements over standard communication interfaces such as RS232, USB, Ethernet or optional GPIB (IEEE-488). Control Control USB, RS-232, Ethernet * PSU Controller * GPIB (IEEE-488) Option available Simplified 12 Channel Block Diagram Model Number Configuration Matrix 842X - XX - XX - X X G Basic Model Number Phase Shifter Number of Channels Designator (01 to 12)* (see below) Example: 8421-A1-12-TS-G GPIB (IEEE-488) Option Blank = Not Installed G = Installed Connector Type S = SMA Female * N = N Female* Up to 2 Channels (8340) & 6 Channels 8341) for option F & R (Front or Rear) Connector Location** F = Front R = Rear T = Front - Rear Electro-mechanical Frequency Range DC to 6 GHz Phase Shifter Designation A 1 Phase Shifter Model 984-1 Range (°) Step Size (dB) Insertion Loss (maximum) 0 - 630 10° 6.0 dB VSWR RoHS (maximum) 1.6 RoHS compliance dependent on phase shifter installed. Some designs are NOT compliant. 14 © API Technologies, Inc. Proprietary Information | weinschel.apitech.com | [email protected] | 301-846-9222 , 800-638-2048 WEINSCHEL Physical Dimensions Model 8420, Half Rack Unit, 1 or 2 channels: API Weinschel, Inc. DIM A API Weinschel, Inc. 8420 SERIES 8420 SERIES Model 8421, Standard 19 in Rack Unit up to 12 channels: DIM “A” 5.97 [.24] 304.80 [12.00] 13.21 [.52] CHAN 1 A CHAN 3 B CHAN 4 B SERIAL CHAN 6 B 2 CHAN 7 B CHAN 8 A CHAN 10 B CHAN 10 A 2 8421 SERIES CHAN 12 A API Weinschel, Inc. 4X HOLE PLUG CHAN 12 B CHAN 11 B 2 MADE IN USA CHAN 11 A 4X HOLE PLUG .25 X .40 LONG SLOT, 4X [6.35] [10.16] 8X CONNECTOR, TYPE N FEMALE CHAN 9 B CONNECTOR, PER IEEE 488.2 PROTOCOL CHAN 9 A 19.3 [.76] TYP FRONT AND REAR CONNECTOR, ETHERNET RJ45 CHAN 8 B 425.20 [16.74] GPIB 8X CONNECTOR, TYPE N FEMALE CHAN 7 A 11X 31.75 = 349.25 [1.250] [13.75] TYPICAL FRONT AND REAR LAN 2 CHAN 6 A 482.60 [19.00] LINK CHAN 5 A CONNECTOR, USB, MINI B ACT USB CHAN 4 A 465.12 [18.312] CONNECTOR, 9 PIN D MALE, RS232 CHAN 3 A 31.75 [1.250] TYPICAL FRONT AND REAR CHAN 2 B POWER INPUT 115/230 VAC 0.5A 50/60Hz CHAN 2 A 28.70 [1.13] TYP FRONT AND REAR CHAN 1 B WEINSCHEL POWER SWITCH CHAN 5 B 76.20 [3.000] CAGE CODE 93459 37.97 [1.50] TYPICAL FRONT AND REAR MODEL: SERNO: 8.74 [.34] 1.27 [.05] 88.14 [3.47] Connector Type N SMA DIM A 14.7 (0.60) 5.21 (0.21) NOTE: 1. All dimensions are given in mm (inches). 2. Connectors and hole plugs are installed as required and determined by number of channel in unit. 2 channel shown for Model 8420 and 8 channel unit shown for 8421. 3. Connector location (Front/Rear) may vary depending on Model ordered. 15 © API Technologies, Inc. Proprietary Information | weinschel.apitech.com | [email protected] | 301-846-9222 , 800-638-2048 Innovative Design Solutions for Performance Driven Applications Programmable Switch Unit, Model 8512 Features o Can be configured with up to 14 each, SP3T, SP4T, SP5T or SP6T Switches. o Front panel local control and display make it ideal for lab and manual test environments. o Up to 26.5 GHz Operating Frequency Range. o Integrated Switch Cycle Counter. o Failsafe (break-before-make) & Latching (makebefore-break) switching functionality available. o Easily expandable - additional switches can be quickly installed by the customer. o Low Insertion Loss and High Isolation. o Supplied with industry standard communication interfaces: - Ethernet (10/100 BaseT) - USB 2.0 - RS-232 (Serial) - GPIB/IEEE-488 optional RoHS The Weinschel Model 8512 Series of Programmable Switch Units offer a compact, expandable, rack mount solution for a variety of test, subsystem, and system applications. The Model 8512 Series operates over the DC to 18/26.5 GHz frequency range, with SP3T to SP6T configurations with up to 14/6 switches respectively. Ethernet, USB, and RS-232 control interfaces are standard, along with LabVIEWTM based control software. A GPIB/IEEE-488 interface is also available as an option. Using the Switch Control Center Software supplied with each unit, the user can quickly set up and operate the unit’s switches independently, or using the Configure Virtual Switch option, create custom “tree” or “matrix” configurations by assigning input, output, and path labels as required. Weinschel also provides custom configurations where a variety of configurations can be incorporated within a single unit. Please contact us with your specialized needs. o LabVIEWTM based Switch Control Software included. o Compact 2 RU, 19” Rack Mount Configuration. Other configurations avaiable. Applications o Wi-Fi, WiMAX, 4G LTE Base Station Testing. o Signal routing from multiple instruments to single or multiple DUTs. o Production Testing - Multiple tests can be performed using the same test setup. o ATE and STE applications requiring configuration flexibility. Control Software Included Weinschel LabVIEWTM based Switch Control Center Software (SCCS) is to be used in conjunction with the operation of the Weinschel 8512 series of programmable switch units. The SCCS will allow the user setup, control and perform tests and measurements using these programmable switch units over standard communication interfaces. Redundant 3 x 3 matrix with fixed attenuators in the redundant paths as an example of an 8512-06-XX application. 16 © API Technologies, Inc. Proprietary Information | weinschel.apitech.com | [email protected] | 301-846-9222 , 800-638-2048 WEINSCHEL Model Number Configuration Matrix Electro-mechanical Switch Designation (See Table) Basic Model Number GPIB (IEEE-488) Option Blank = Not Installed G = Installed Number of Switches Installed (01 to 14)* Connector Location F = Front R = Rear * Up to 6 Channels for Option C Switch Designation Switch Description 8512 - XX - XX - X G Example: 8512-A6-07-F Physical Dimensions DC-18 GHz, Failsafe to open, Make Before Break, SMA Female A DC-18 GHz, Latching, Make Before Break, SMA Female B DC-26.5 GHz, Failsafe to open, Break Before Make, SMA Female C # of Positions 3 4 5 6 3 4 5 6 3 4 5 6 SP3T SP4T SP5T SP6T SP3T SP4T SP5T SP6T SP3T SP4T SP5T SP6T Options A & B: POWER SWITCH 88.1 [3.47] 1/4-20 GND STD AIR VENTS 76.2 [3.00] 5.9 [.23] 304.8 [12.00] 38.1 [1.50] 1.7 [.07] 10.4 [.41] 84.7 [3.33] POWER INPUT 115/230 VAC CONNECTOR, 9 PIN D, MALE, SERIAL MODEL: 8512-A6-XX-R SERNO: XXXX CAGE CODE 93459 DISPLAY MADE IN USA API Weinschel, Inc. SCROLL-WHEEL CONTROL BUTTON SERIAL CONNECTOR, USB, MINI-B CONNECTOR, ETHERNET RJ45 SW 1 SW 8 SW 2 SW 9 SW 3 SW 10 425.2 [16.74] SW 4 SW 11 6 X 37.47 = 224.8 [1.475] [8.85] 6 X 37.47 = 224.8 [1.475] [8.85] 2 SW 5 SW 12 SW 5 SW 12 SW 7 SW 14 SW 7 SW 14 SW 6 SW 13 37.5 [1.48] SW 6 SW 13 37.5 [1.48] SWITCH COVER PLATE SW 4 SW 11 482.6 [19.00] CONNECTOR, GPIB (OPTIONAL) SW 3 SW 10 SW 1 SW 8 465.3 [18.32] SW 2 SW 9 LINK LAN ACT USB GPIB 14 X SWITCH COVER PLATE 8512 SERIES 64.3 [2.53] 35.6 [1.40] 8.6 [.34] 21.8 [.86] 55.1 [2.17] 4X SLOTS 7.1 [.28] X 10.2 [.40] 56.7 [2.23] 20.3 [.80] AIR VENTS 19.2 [.76] 9.6 [.38] 5.6 [.22] 4 1 9.6 [.38] 9.6 [.38] 9.6 [.38] 3 19.2 [.76] 19.2 [.76] 19.2 [.76] 1 5.6 [.22] 11.1 [.44] 5.6 [.22] 1 11.1 [.44] 6 5.6 [.22] 1 11.1 [.44] 30° 2 11.1 [.44] 1. 2. 22.2 B.C. [.88] 3 2 30° 22.2 B.C. [.88] SP3T, SWITCH PORTS NOTE: 5 C C SP4T, SWITCH PORTS C 4 22.2 [.88] 2 3 11.1 [.44] 30° 5 11.1 [.44] C 4 2 30° 3 22.2 B.C. [.88] SP5T, SWITCH PORTS SP6T, SWITCH PORTS DETAIL A SCALE 2 : 1 ROTATED 90° CW 22.2 B.C. [.88] All dimensions are given in mm (inches). RF Switches and switch plates as required and determined by configuration. Seven switch unit configuration shown. 17 © API Technologies, Inc. Proprietary Information | weinschel.apitech.com | [email protected] | 301-846-9222 , 800-638-2048 Innovative Design Solutions for Performance Driven Applications Physical Dimensions Options C: 88.1 [3.47] 5.9 [.23] AIR VENT 76.2 [3.00] 38.1 [1.50] 304.8 [12.00] 1.7 [.07] 10.4 [.41] 84.7 [3.33] 1/4-20 GND STD MODEL: SERNO: CAGE CODE 93459 MADE IN USA API Weinschel, Inc. DISPLAY POWER INPUT 115/230 VAC CONNECTOR, 9 PIN D, MALE, SERIAL LINK LAN ACT USB GPIB SERIAL POWER SWITCH SCROLL-WHEEL CONTROL BUTTON CONNECTOR, USB, MINI-B SW 1 465.3 [18.32] CONNECTOR, ETHERNET RJ45 2 SW 2 RF SWITCH SP6T, W/SMA FEMALE CONNECTORS, MATING REQUIREMENTS PER MIL-STD-348 SEE DETAIL A 482.6 [19.00] SW 3 5 X 44.96 = 224.8 [1.77] [8.85] 425.2 [16.74] CONNECTOR, GPIB (OPTIONAL) SW 4 6X, COVER PLATE SWITCH SW 5 44.96 [1.77] SW 6 4X SLOTS 7.1 [.28] X 10.2 [.40] 8512 SERIES 61.73 [2.43] 44.06 [1.73] 8.6 [.34] AIR VENT 23.4 [.92] 11.7 [.46] 23.4 [.92] 11.7 [.46] 6.7 [.27] 13.5 [.53] 6 1 C 5 27.0 [1.06] 3 4 SP6T, SWITCH PORTS DETAIL A SCALE 2 : 1 ROTATED 90° 13.5 [.53] 27.0 [1.06] 3 27.0 B.C. [1.06] 4 13.5 [.53] 5 4 SP5T, SWITCH PORTS 3 1 C 13.5 [.53] 3 2 30° 30° R13.5 B.C. [.53] 1 13.5 [.53] C 2 23.4 [.92] 11.7 [.46] 6.7 [.27] 2 C 30° 23.4 [.92] 6.7 [.27] 1 13.5 [.53] 2 11.7 [.46] 30° SP4T, SWITCH PORTS R13.5 B.C. [.53] 6.7 [.27] SP3T, SWITCH PORTS R13.5 B.C. [.53] NOTE: 1. All dimensions are given in mm (inches). 2. RF Switches and switch plates as required and determined by configuration. Six switch unit configuration shown. 18 © API Technologies, Inc. Proprietary Information | weinschel.apitech.com | [email protected] | 301-846-9222 , 800-638-2048 WEINSCHEL Model 8390 & 8390-1 Amplifier / Switch Units AT10 3T-2 S4 J8 2 C 1 S6 J7 AT9 3T-2 2 C 1 AT8 3T-2 S3 J6 2 AT2 3T-1 AMP1 AT1 150T-31 0-31 dB 1 dB STEPS 2 S8 S7 2 C C 1 1 AT6 3T-2 S2 Weinschel Models 8390 and 8390-1, Amplifier / Switch Unit is comprised of an array of eight input switches (S1-S8), a relaybased step attenuator that provides 0-31 dB of attenuation in 1 dB steps and an output RF amplifier. Switch, S8 is terminated with a 50 Ω termination at port 2. Each input/output port contains a masking pad. The unit includes a front-panel interface for status and control, and supports programming via a serial RS232 port and/or 10/100 BaseT Ethernet port. J5 AT7 3T-2 RF INPUT 1 50 Ω RF OUTPUT C J4 2 C J3 1 FRONT PANEL S5 AT5 3T-2 2 C 1 AT4 3T-2 S1 J2 2 C 1 J1 AT3 3T-2 REAR PANEL Simplified Block Diagram o Choice of Frequency Ranges.: - Model 8390: 3.4 to 4.2 GHz - Model 8390-1: 0.95 to 13 GHz EXPORT CONTROL: This product is controlled for export under the International Traffic in Arms Regulations (ITAR). A license from the U.S. Department of State is required prior to the export of this product from the United States. o Can be rack mounted into any rack or cabinet designed per EIA RS-310 or MIL-STD-189. EXPORT WARNING: Military and space products are controlled for export under the International Traffic in Arms Regulations (ITAR) and may not be sold or proposed or offered for sale to certain countries. (See ITAR 126.1 for complete information.) Physical Dimensions AIR EXHAUST MODEL: 8390 SERNO: XXXX CAGE CODE 93459 MADE IN USA Aeroflex / Weinschel 43.7 [1.72] 31.7 [1.25] .4 [.02] 5.9 [.23] 42.7 [1.68] 454.0 [17.88] 27.4 [1.08] 1/4-20 GND STD 1 AC INPUT 115-230 VOLTS 50-60 Hz 2 3 4 S1 ~ 50-60 Hz 115-230V, 50W FUSE: F1.5, 250V 5 8 ACT 7 J8 LINK HEADER FOR SWITCH MARKINGS 429.8 [16.92] RJ45 J7 425.2 [16.74] 3X, SINGLE DIGIT DISPLAY J6 465.3 [18.32] ATTEN (dB) 482.6 [19.00] CONNECTOR, 9 PIN D, FEMALE SERIAL 6 8X, PUSH-BUTTON SWITCH J5 2X, PUSH-BUTTON SWITCH J3 J4 RF OUTPUT 8X, CONNECTOR TYPE N, FEMALE (INPUTS) J2 J1 AMPLIFIER/ SWITCH UNIT MODEL 8390 -1 CONNECTOR TYPE N, FEMALE (OUTPUT) 609.6 [24.00] 8.6 [.34] 2X SUPPORTS 4X SLOTS 7.1 [.28] X 10.2 [.40] AIR INTAKE NOTE: All dimensions are given in mm (inches) and are maximum, unless otherwise specified. © API Technologies, Inc. Proprietary Information | weinschel.apitech.com | [email protected] | 301-846-9222 , 800-638-2048 19 Innovative Design Solutions for Performance Driven Applications Precision Step Attenuator Unit, Model 3057 Specifications 50 Ω dc to 1.5 GHz 0 to 50 dB 0.1 dB, 1.0 dB, 10.0 dB 0 - 0.9 dB: +0.1 dB 1.0 - 50 dB: +0.2 dB INSERTION LOSS: 1.5 dB maximum VSWR: 1.3:1 maximum NOMINAL IMPEDANCE: FREQUENCY RANGE: ATTENUATION RANGE: RESOLUTION: Attenuation Accuracy: Model 3057 Series Precision Step Attenuators are designed for use in automatic test equipment and OEM systems operating in the DC to 1.5 GHz frequency range. This design contains three API Weinschel Manual Step Attenuators connected in series to provide 0 to 50 dB of attenuation with 0.1, 1.0 and 10.0 dB of resolution. REPEATABILITY: 0.02 dB o Wide Dynamic Range - Up to 50 dB of attenuation with 0.1 dB resolution. o Excellent Repeatability. o Highly Accurate Detent Stepping o Compact 2 RU, 19” Rack Mount Configuration. MAXIMUM POWER RATING: 1 watt TEMPERATURE RANGE: Operating: Nonoperating: 0°C to + 54°C -54°C to +54°C Low Passive Intermodulation Fixed Attenuators & Terminations Weinschel announces a New line of Low Passive Intermodulation (PIM) coaxial fixed attenuators and terminations. These designs offer models with power handling up to 175 watts with PIM levels, 3rd Order IM Magnitude (IM3) down to -120 dBc to -150 dBc. o o o Low PIM design Quality connectors with special high temperature support beads Rugged construction, free of solder joints. Models 254 /1479 Fixed Attenuators Model Number Models 298 /1492 Model 264 Connector Type Frequency Range (GHz) Average Power (W) Standard Attenuation Values (dB) SWR (maximum) 264-XX-XX SMK (2.92mm)/ N DC-8.5 50 10, 20, 30, 40 1.20-1.30* 298-XX-XX SMK (2.92mm)/ N DC-6.0 100 10, 20, 30, 40 1.10-1.15* 254-XX-XX SMK (2.92mm)/ N DC-6.5 175 10, 20, 30, 40 1.10-1.20* Terminations & Loads Model Number Connector Type Frequency Range (GHz) Average Power (W) SWR (maximum) 1491-X SMK (2.92mm) / N DC-8.5 50 1.20-1.30* 1492-X SMK (2.92mm) / N DC-6.5 100 1.20 1479-X SMK (2.92mm) / N DC-6.5 175 1.10-1.20* Notes: 1. 2. * = VARIES WITH FREQUENCY. Connector Option: 1 (SMK female) 2 (SMK male) 3 (N female) 4 (N male) Model 1491 264 - XX - XX Basic Model Number Attenuation Value (dB) Connector Options 1st digit is input side 2nd digit is output side 20 © API Technologies, Inc. Proprietary Information | weinschel.apitech.com | [email protected] | 301-846-9222 , 800-638-2048 WEINSCHEL Conduction Cooled (Flat-Pack) Fixed Attenuators & Terminations API Weinschel line of conduction cooled flat-pack coaxial fixed attenuators and terminations is expanding to include new models covering the DC to 10 GHz frequency range. These products offer several models with power handling up to 550 watts. o Precision Connectors with high temperature support beads o Designed to meet environmental requirements of MIL-DTL-3933 o 10 Kilowatts peak, Conduction Cooled o Low Intermodulation Distortion Option available on select models o Wireless Applications - Optimized for use in the communications bands Fixed Attenuators Model Number Frequency Range (GHz) Average Power (W) Peak Power (kW) 253-XX-XX** SMK (2.92mm) / N DC-6.0 550 10 10, 20, 30, 40 257-XX-XX** SMK (2.92mm) / N DC-6.0 250 10 10, 20, 30, 40 1.10 258-XX-XX** SMK (2.92mm)/ N DC-6.0 400 10 10, 20, 30, 40 1.10-1.25* 268-XX-XX** SMK (2.92mm) / N DC-6.0 100 10 6, 10, 20, 30, 40 1.10-1.15* SMK (2.92mm) DC-40.0 5 0.2 3, 6, 10, 20. 30 1.25-1.45* 284-XX-XX** SMK (2.92mm)/ N DC-10.0 50 5 3. 6, 10, 20, 30, 40 1.15-1.30* 285-XX-XX** SMK (2.92mm)/ N DC-10.0 100 10 10, 20, 30, 40 1.10-1.50* 286-XX-XX** SMK (2.92mm)/ N DC-10.0 150 10 10, 20, 30, 40 1.10-1.50* 287-XX-XX** SMK (2.92mm)/ N DC-10.0 200 10 10, 20, 30, 40 1.10-1.20* 275-XX-XX Notes: 1. 2. 3. * = VARIES WITH FREQUENCY. ** = Low Intermodulation available Connector Option: 1 (SMK female) 2 (SMK male) 3 (N female) 4 (N male) Standard Attenuation Values (dB) SWR1 (maximum) Connector Type 1.10-1.20* 253 - XX - XX - LIM IM Option Basic Model Number Attenuation Value (dB) Connector Options 1st digit is input side 2nd digit is output side * Add -LIM for Low Intermodulation option. Terminations & Loads Model Number Connector Type Frequency Range (GHz) Average Power (W) Peak Power (kW) SWR1 (maximum) 1470-X** SMK (2.92mm) / N DC-6.0 100 10 1.20 1471-X** SMK (2.92mm) / N DC-6.0 250 10 1.20 1472-X** SMK (2.92mm) / N DC-6.0 400 10 1.20 1473-X** SMK (2.92mm) / N DC-6.0 550 10 1.20 1474-X** SMK (2.92mm) DC-40.0 5 0.2 1.25-1.45* 1476-X SMK (2.92mm) / N DC-10.0 50 5 1.15-1.30* 1482-X** SMK (2.92mm) / N DC-10.0 100 10 1.20 1483-X** SMK (2.92mm) / N DC-10.0 150 10 1.20 1484-X** SMK (2.92mm) / N DC-10.0 200 10 1.20 Notes: 1. 2. 3. * = VARIES WITH FREQUENCY. ** = Low Intermodulation available. Add -LIM to Model number -X = Connector Option: -1 (SMK female), -2 (SMK male), -3 (N female), -4 (N male) 21 © API Technologies, Inc. Proprietary Information | weinschel.apitech.com | [email protected] | 301-846-9222 , 800-638-2048 Innovative Design Solutions for Performance Driven Applications High Reliability Attenuators (DC to 18 / 40 GHz) Model 273 Since 1952, Weinschel has supplied high quality precision coaxial attenuators and terminations to test and calibration labs throughout the world. These products offer rugged construction, frequency ranges up to 40 GHz, many standard dB values and power handling to 1,500 Watts. Weinschel has released the Model 32K, DC to 40 GHz, 2 Watt High Reliability Fixed Coaxial Attenuator designed specifically for space applications. The Model 32K is available with SMK connectors in dB values of 3, 6, 10, 20 and 30. Other features include 1.25-1.45 maximum SWR, + 1.00-1.50 dB deviation, quality connectors, and an operating temperature range of -55 °C to +100 °C. Model 274 Model 32K Also being introduced is a line of hi-reliability fixed attenuators (Models 272-274, 276) specifically designed as commercial alternative to MIL-DTL-3933 CLASS IIWI/IVE, N/S (N=Non-Screened, S=Screened) attenuators. These units are designed to meet the MIL-DTL-3933 requirements. Model 272 Model 276 Connector Type Frequency Range (GHz) 32K SMK (f-m) DC-40.0 2 0.50 3, 6, 10, 20, 30 1.25-1.45 272-XX-N/S N (f-m) DC-18.0 2 0.5 1- 10, 20, 30, 40 1.12-1.20 273-XX-N/S SMA (f-m) DC-18.0 2 0.5 0-10 in 0.5 increments, 11- 20 in 1 increments, 25 - 40 in 5 increments 1.10-1.35 274-XX-N/S SMA (f-m) DC-18.0 2 0.5 0-20 in 0.5 increments, 30, 40 1.15-1.35 276-XX-N/S N (f-m) DC-18.0 25 1.0 3, 6, 10, 20, 30 1.15-1.40 Notes: Average Peak Power (W) Power (kW) Standard Attenuation Values (dB) SWR1 (maximum) Model Number 1. VARIES WITH FREQUENCY. 2. Custom dB values available. XX = Standard dB Value, f = female, m = Male Features Screening o Screened and Non-screened models available. Units are screened as follows: o Choice of attenuation values. o Frequency Ranges from DC to 18 GHz. o Power capability from 2 to 25 watts. o Test Data supplied at additional cost as follows: Non-screened (N): Swept data plots of Attenuation and SWR across the frequency band. Screened (S): Swept data plots of Attenuation and SWR across the frequency band. Film, Standard data package includes lot record performance showing pass/fail quantities for all tests and test reports as applicable. "N" versions: SWR Attenuation Peak Power "S" versions: Thermal Shock Monitored Thermal Cycle (MTC) Attenuation w/Parts Assembly Verification (PAV) Conditioning Peak Power Attenuation SWR Radiographics 22 © API Technologies, Inc. Proprietary Information | weinschel.apitech.com | [email protected] | 301-846-9222 , 800-638-2048 WEINSCHEL Medium & High Power Attenuators, Terminations & Mismatches (DC to 6 / 18 GHz) Model 279 / 1477 API Weinschel continues to expand its medium and high power fixed coaxial attenuator and termination offering with the additions of new models with: o The Model 251 is a convection cooled, 200 W Bi-directional design that operates over the DC to 6 GHz frequency range. Available in standard dB values of 10, 20, 30 and 40. Standard Type N or SMK (2.92mm) connectors. o Designs DC to 40 GHz, 10 W (Model 279 / 1477) and 20 W (Model 89 / 1478) with choice of SMK (2.92mm) male / female connectors. o New body style 50 W (Model 90 / 1468) and 100 W (Model 260 / 1467) designs that operate over the DC to 18 GHz frequency range with Type N or 3.5mm connectors and are available in 50 W or 100 W configurations. Standard dB values: 3, 6, 10, 20, 30. o API Weinschel introduces a new line of Medium and High Power Mismatches that operate over the DC to 6 GHz frequency range. This Model offers mismatch SWR values of 2 to 6.5 in 0.5 increments. Model 89 / 1478 Model 90 / 1467 Model 290/1479 Model 251 Fixed Attenuators Model Number Connector Type Frequency Range (GHz) Average Power (W) Peak Power (kW) 89-XX-XX SMK (2.92mm) DC-40.0 20 0.2 90-XX-XX 3.5mm / N DC-18.0 50 1 251-XX-XX SMK (2.92mm) / N DC-6.0 200 260-XX-XX 3.5mm / N DC-18.0 100 279-XX-XX SMK (2.92mm) DC-40.0 10 290-XX-XX 3.5mm / N DC-18.0 300 Standard Attenuation Values (dB) Model 260 / 1469 SWR1 (maximum) 10, 20, 30 1.25-1.40* 3, 6, 10, 20, 30 1.15-1.30 10 10, 20, 30, 40 1.10-1.20 1 3, 6, 10, 20, 30 1.15-1.30 0.2 10, 20, 30 1.20-1.35* 10 10, 20, 30, 40 1.10-1.20 Terminations & Loads Model Number Connector Type Frequency Range (GHz) Average Power (W) Peak Power (kW) SWR1 (maximum) 1467-X 3.5mm / N DC-20.0 50 1 1.30-1.60* 1468-X BNC / SMA / N DC-6.0 50 1 1.15-1.20 1469-X 3.5mm / N DC-18.0 100 1 1.15 1475-X 3.5mm / N DC-18.0 150 1 1.90 1477-X SMK (2.92mm) DC-40.0 10 0.2 1.25-1.40* 1478-X SMK (2.92mm) DC-40.0 20 0.2 1.25-1.40* 1479-X 3.5mm / N DC-18.0 300 10 1.90 Model 1468 Model 1475 Model 1060 Mismatches Model Number Connector Type Frequency Range (GHz) Average Power (W) Peak Power (kW) Mismatch SWR 1060-M-X N / 3.5mm) DC-6.0 25 5 2 to 6.5 in 0.5 values 1061-M-X N / SMK (2.92mm) DC-6.0 50 10 2 to 6.5 in 0.5 values 1062-M-X N / SMK (2.92mm) DC-6.0 100 10 2 to 6.5 in 0.5 values Notes: Model 1061 Models 1062 1. * = VARIES WITH FREQUENCY. 23 © API Technologies, Inc. Proprietary Information | weinschel.apitech.com | [email protected] | 301-846-9222 , 800-638-2048 Innovative Design Solutions for Performance Driven Applications Get the latest Products Information from API Weinschel. . . RF & Microwave Components & Subsystems Catalog The New Weinschel Full-line catalog outlines their wide range of RF, Wireless, and Microwave Components and Subsystems that operate over the DC to 50 GHz frequency range. Included are programmable step attenuators including MMIC, PIN, FET, relay and edge-line technologies, resistive power splitters, dividers, high power (up to 1500 watts) and low passive IM fixed attenuators, coaxial terminations, continuously variable and manual step attenuators, Planar Blind-mate and Planar Crown connector systems, custom and RF simulation subsystems. Visit our website @ .... weinschel.apitech.com Weinschel website is updated daily and outlines a wide variety of Standard RF & Microwave Components & Subsystems that operate over the DC to 50 GHz frequency range. Weinschel also designs and manufactures Custom RF & Microwave Components & subsystems for application specific customer requirements. About API Weinschel For over sixty years the name Weinschel has become synonymous with leadership in RF and microwave technologies and superior quality components and subsystems for wireless, defense, test and measurement, and broadband markets throughout the world. Among its many technological achievements, Weinschel was the first to design and manufacture commercially available coaxial attenuators. Today, built upon a strong heritage, Weinschel (formerly Aeroflex / Weinschel) continues to provide a vast array of standard products together with custom-engineered solutions to satisfy demanding market needs for precision and high reliability coaxial components. The Weinschel product offering includes fixed attenuators for test, metrology and space applications; continuously variable, manual step, solid-state digital step and programmable step attenuators; high power terminations; resistive splitters and dividers; manual phase shifters; Planar Blind-Mate ®, Planar Crown® connectors. In addition to coaxial components covering DC-50 GHz, Weinschel offers a complete range of standard and custom-designed SmartStep ® multi-path switching, combining, and attenuation subsystems for cable infrastructure and mobile wireless test applications, including RF simulation, multi-path and fading, high-power hot-switching attenuation, RF signal conditioning, RF and IF signal routing, and production testing. 5305 Spectrum Drive, Frederick, MD 21703-7362 Tel: 800-638-2048, 301-846-9222 Fax: 301-846-9116 weinschel.apitech.com [email protected]