TI MSP430F2101IRGET

MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
MIXED SIGNAL MICROCONTROLLER
FEATURES
1
•
•
•
•
•
•
•
•
Low Supply Voltage Range: 1.8 V to 3.6 V
Ultra-Low Power Consumption
– Active Mode: 250 μA at 1 MHz, 2.2 V
– Standby Mode: 0.7 μA
– Off Mode (RAM Retention): 0.1 μA
Ultra-Fast Wake-Up From Standby Mode in
Less Than 1 μs
16-Bit RISC Architecture, 62.5-ns Instruction
Cycle Time
Basic Clock Module Configurations
– Internal Frequencies up to 16 MHz With
Four Calibrated Frequencies to ±1%
– 32-kHz Crystal
– High-Frequency Crystal up to 16 MHz
– Resonator
– External Digital Clock Source
16-Bit Timer_A With Three Capture/Compare
Registers
On-Chip Comparator for Analog Signal
Compare Function or Slope Analog-to-Digital
(A/D) Conversion
Brownout Detector
•
•
•
•
•
•
Serial Onboard Programming, No External
Programming Voltage Needed, Programmable
Code Protection by Security Fuse
Bootstrap Loader
On Chip Emulation Module
Family Members:
– MSP430F2101
– 1KB + 256B Flash Memory
– 128B RAM
– MSP430F2111
– 2KB + 256B Flash Memory
– 128B RAM
– MSP430F2121
– 4KB + 256B Flash Memory
– 256B RAM
– MSP430F2131
– 8KB + 256B Flash Memory
– 256B RAM
Available in a 20-Pin Plastic Small-Outline
Wide Body (SOWB) Package, 20-Pin Plastic
Small-Outline Thin (TSSOP) Package, 20-Pin
TVSOP Package, and 24-Pin QFN Package
For Complete Module Descriptions, See the
MSP430x2xx Family User’s Guide (SLAU144)
DESCRIPTION
The Texas Instruments MSP430 family of ultra-low-power microcontrollers consist of several devices featuring
different sets of peripherals targeted for various applications. The architecture, combined with five low-power
modes, is optimized to achieve extended battery life in portable measurement applications. The device features a
powerful 16-bit RISC CPU, 16-bit registers, and constant generators that contribute to maximum code
efficiency.The digitally controlled oscillator (DCO) allows wake-up from low-power modes to active mode in less
than 1 μs.
The MSP430x21x1 series is an ultra-low-power mixed signal microcontroller with a built-in 16-bit timer, versatile
analog comparator, and sixteen I/O pins.
Typical applications include sensor systems that capture analog signals, convert themto digital values, and then
process the data for display or for transmission to a host system. Stand-alone RF sensor front end is another
area of application. The analog comparator provides slope A/D conversion capability.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2004–2011, Texas Instruments Incorporated
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
Table 1. Available Options
PACKAGED DEVICES
TA
-40°C to 85°C
-40°C to 105°C
PLASTIC
20-PIN SOWB
(DW)
PLASTIC
20-PIN TSSOP
(PW)
PLASTIC
20-PIN TVSOP
(DGV)
PLASTIC
24-PIN QFN
(RGE)
MSP430F2101IDW
MSP430F2101IPW
MSP430F2101IDGV
MSP430F2101IRGE
MSP430F2111IDW
MSP430F2111IPW
MSP430F2111IDGV
MSP430F2111IRGE
MSP430F2121IDW
MSP430F2121IPW
MSP430F2121IDGV
MSP430F2121IRGE
MSP430F2131IDW
MSP430F2131IPW
MSP430F2131IDGV
MSP430F2131IRGE
MSP430F2101TDW
MSP430F2101TPW
MSP430F2101TDGV
MSP430F2101TRGE
MSP430F2111TDW
MSP430F2111TPW
MSP430F2111TDGV
MSP430F2111TRGE
MSP430F2121TDW
MSP430F2121TPW
MSP430F2121TDGV
MSP430F2121TRGE
MSP430F2131TDW
MSP430F2131TPW
MSP430F2131TDGV
MSP430F2131TRGE
Development Tool Support
All MSP430 microcontrollers include an Embedded Emulation Module (EEM) that allows advanced debugging
and programming through easy-to-use development tools. Recommended hardware options include:
• Debugging and Programming Interface with Target Board
– MSP-FET430U28 (PW package)
• Debugging and Programming Interface
– MSP-FET430UIF (USB)
– MSP-FET430PIF (Parallel Port)
• Target Board
– MSP-TS430PW28 (PW package)
• Production Programmer
– MSP-GANG430
2
Copyright © 2004–2011, Texas Instruments Incorporated
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
Device Pinout
DW, PW, or DGV PACKAGE
(TOP VIEW)
TEST
VCC
P2.5/CA5
VSS
XOUT/P2.7/CA7
XIN/P2.6/CA6
RST/NMI
P2.0/ACLK/CA2
P2.1/INCLK/CA3
P2.2/CAOUT/TA0/CA4
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
P1.7/TA2/TDO/TDI
P1.6/TA1/TDI/TCLK
P1.5/TA0/TMS
P1.4/SMCLK/TCK
P1.3/TA2
P1.2/TA1
P1.1/TA0
P1.0/TACLK
P2.4/TA2/CA1
P2.3/TA1/CA0
P2.5/CA5
VCC
TEST
P1.7/TA2/TDO/TDI
P1.6/TA1/TDI/TCLK
NC
RGE PACKAGE
(TOP VIEW)
24 23 22 21 20 19
18
1
17
2
16
3
Exposed
4 Thermal Pad 15
5
14
6
13
7 8 9 10 11 12
P1.5/TA0/TMS
P1.4/SMCLK/TCK
P1.3/TA2
P1.2/TA1
P1.1/TA0
P1.0/TACLK
P2.1/INCLK/CA3
P2.2/CAOUT/TA0/CA4
NC
P2.3/TA1/CA0
P2.4/TA2/CA1
NC
NC
VSS
XOUT/P2.7/CA7
XIN/P2.6/CA6
RST/NMI
P2.0/ACLK/CA2
A.
NC = Not internally connected
B.
Exposed thermal pad connection to VSS recommended.
Copyright © 2004–2011, Texas Instruments Incorporated
3
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
Functional Block Diagram
VCC
VSS
P1.x, JTAG
8
P2.x,
XIN/XOUT
8
XOUT
XIN
Basic Clock
System+
ACLK
SMCLK
MCLK
16MHz
CPU
incl. 16
Registers
Flash
RAM
8kB
4kB
2kB
1kB
256B
256B
128B
128B
Port P1
Comparator
_A+
8 Channel
Input Mux
8 I/ O
Interrupt
capability,
pullup/down
resistors
Port P2
8 I/ O
Interrupt
capability,
pullup/down
resistors
MAB
MDB
Emulation
(2BP)
JTAG
Interface
Brownout
Protection
Watchdog
WDT+
15/16 Bit
Timer_A3
3 CC
Registers
RST/NMI
NOTE: See port schematics section for detailed I/O information.
4
Copyright © 2004–2011, Texas Instruments Incorporated
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
Table 2. Terminal Functions
TERMINAL
NO.
DW,
PW,
or
DGV
RGE
P1.0/TACLK
13
13
I/O
P1.1/TA
14
14
I/O
P1.2/TA1
15
15
I/O
P1.3/TA2
16
16
I/O
P1.4/SMCLK/TCK
17
17
I/O
P1.5/TA/TMS
18
18
I/O
P1.6/TA1/TDI/TCLK
19
20
I/O
P1.7/TA2/TDO/TDI (1)
20
21
I/O
P2.0/ACLK/CA2
8
6
I/O
P2.1/INCLK/CA3
9
7
I/O
P2.2/CAOUT/TA/CA4
10
8
I/O
NAME
I/O
DESCRIPTION
General-purpose digital I/O pin
Timer_A, clock signal TACLK input
General-purpose digital I/O pin
Timer_A, capture: CCI0A input, compare: Out0 output/BSL transmit
General-purpose digital I/O pin
Timer_A, capture: CCI1A input, compare: Out1 output
General-purpose digital I/O pin
Timer_A, capture: CCI2A input, compare: Out2 output
General-purpose digital I/O pin / SMCLK signal output
Test Clock input for device programming and test
General-purpose digital I/O pin / Timer_A, compare: Out0 output
Test Mode Select input for device programming and test
General-purpose digital I/O pin / Timer_A, compare: Out1 output
Test Data Input or Test Clock Input for programming and test
General-purpose digital I/O pin / Timer_A, compare: Out2 output
Test Data Output or Test Data Input for programming and test
General-purpose digital I/O pin / ACLK output
Comparator_A+, CA2 input
General-purpose digital I/O pin / Timer_A, clock signal at INCLK
Comparator_A+, CA3 input
General-purpose digital I/O pin
Timer_A, capture: CCI0B input/BSL receive
Comparator_A+, output / CA4 input
P2.3/CA0/TA1
11
10
I/O
P2.4/CA1/TA2
12
11
I/O
P2.5/CA5
3
24
I/O
General-purpose digital I/O pin / Timer_A, compare: Out1 output
Comparator_A+, CA0 input
General-purpose digital I/O pin / Timer_A, compare: Out2 output
Comparator_A+, CA1 input
General-purpose digital I/O pin
Comparator_A+, CA5 input
Input terminal of crystal oscillator
XIN/P2.6/CA6
6
4
I/O
General-purpose digital I/O pin
Comparator_A+, CA6 input
Output terminal of crystal oscillator
XOUT/P2.7/CA7 (2)
5
3
I/O
RST/NMI
7
5
I
Reset or nonmaskable interrupt input
TEST
1
22
I
Selects test mode for JTAG pins on Port1. The device protection fuse is connected to
TEST.
VCC
2
23
Supply voltage
VSS
4
2
Ground reference
NA
Pad
General-purpose digital I/O pin
Comparator_A+, CA7 input
QFN Pad
(1)
(2)
NA
QFN package thermal pad. Connect to VSS.
TDO or TDI is selected via JTAG instruction.
If XOUT/P2.7/CA7 is used as an input, excess current will flow until P2SEL.7 is cleared. This is due to the oscillator output driver
connection to this pad after reset.
Copyright © 2004–2011, Texas Instruments Incorporated
5
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
SHORT-FORM DESCRIPTION
CPU
The MSP430™ CPU has a 16-bit RISC architecture
that is highly transparent to the application. All
operations, other than program-flow instructions, are
performed as register operations in conjunction with
seven addressing modes for source operand and four
addressing modes for destination operand.
Program Counter
PC/R0
Stack Pointer
SP/R1
SR/CG1/R2
Status Register
Constant Generator
CG2/R3
General-Purpose Register
R4
General-Purpose Register
R5
General-Purpose Register
R6
General-Purpose Register
R7
General-Purpose Register
R8
General-Purpose Register
R9
General-Purpose Register
R10
Instruction Set
General-Purpose Register
R11
The instruction set consists of 51 instructions with
three formats and seven address modes. Each
instruction can operate on word and byte data.
Table 3 shows examples of the three types of
instruction formats; Table 4 shows the address
modes.
General-Purpose Register
R12
General-Purpose Register
R13
General-Purpose Register
R14
General-Purpose Register
R15
The CPU is integrated with 16 registers that provide
reduced
instruction
execution
time.
The
register-to-register operation execution time is one
cycle of the CPU clock.
Four of the registers, R0 to R3, are dedicated as
program counter, stack pointer, status register, and
constant generator respectively. The remaining
registers are general-purpose registers.
Peripherals are connected to the CPU using data,
address, and control buses and can be handled with
all instructions.
Table 3. Instruction Word Formats
EXAMPLE
OPERATION
Dual operands, source-destination
INSTRUCTION FORMAT
ADD R4,R5
R4 + R5 → R5
Single operands, destination only
CALL R8
PC → (TOS), R8 → PC
JNE
Jump-on-equal bit = 0
Relative jump, unconditional/conditional
Table 4. Address Mode Descriptions
ADDRESS MODE
SYNTAX
EXAMPLE
OPERATION
✓
✓
MOV Rs,Rd
MOV R10,R11
R10 → R11
Indexed
✓
✓
MOV X(Rn),Y(Rm)
MOV 2(R5),6(R6)
M(2+R5) → M(6+R6)
Symbolic (PC relative)
✓
✓
MOV EDE,TONI
M(EDE) → M(TONI)
Absolute
✓
✓
MOV &MEM,&TCDAT
M(MEM) → M(TCDAT)
Indirect
✓
MOV @Rn,Y(Rm)
MOV @R10,Tab(R6)
M(R10) → M(Tab+R6)
Indirect autoincrement
✓
MOV @Rn+,Rm
MOV @R10+,R11
M(R10) → R11
R10 + 2 → R10
Immediate
✓
MOV #X,TONI
MOV #45,TONI
#45 → M(TONI)
6
D
(2)
Register
(1)
(2)
S
(1)
S = source
D = destination
Copyright © 2004–2011, Texas Instruments Incorporated
MSP430F21x1
www.ti.com
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
Operating Modes
The MSP430 microcontrollers have one active mode and five software-selectable low-power modes of operation.
An interrupt event can wake up the device from any of the five low-power modes, service the request, and
restore back to the low-power mode on return from the interrupt program.
The following six operating modes can be configured by software:
• Active mode (AM)
– All clocks are active.
• Low-power mode 0 (LPM0)
– CPU is disabled.
– ACLK and SMCLK remain active. MCLK is disabled.
• Low-power mode 1 (LPM1)
– CPU is disabled ACLK and SMCLK remain active. MCLK is disabled.
– DCO dc-generator is disabled if DCO not used in active mode.
• Low-power mode 2 (LPM2)
– CPU is disabled.
– MCLK and SMCLK are disabled.
– DCO dc-generator remains enabled.
– ACLK remains active.
• Low-power mode 3 (LPM3)
– CPU is disabled.
– MCLK and SMCLK are disabled.
– DCO dc-generator is disabled.
– ACLK remains active.
• Low-power mode 4 (LPM4)
– CPU is disabled.
– ACLK is disabled.
– MCLK and SMCLK are disabled.
– DCO dc-generator is disabled.
– Crystal oscillator is stopped.
Copyright © 2004–2011, Texas Instruments Incorporated
7
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
Interrupt Vector Addresses
The interrupt vectors and the power-up starting address are located in the address range of 0xFFFF to 0xFFC0.
The vector contains the 16-bit address of the appropriate interrupt handler instruction sequence.
If the reset vector (located at address 0xFFFE) contains 0xFFFF (for example, if flash is not programmed), the
CPU goes into LPM4 immediately after power up.
Table 5. Interrupt Vector Addresses
INTERRUPT SOURCE
INTERRUPT FLAG
Power-up
PORIFG
External reset
RSTIFG
Watchdog
WDTIFG
Flash key violation
KEYV (1)
SYSTEM INTERRUPT
WORD ADDRESS
PRIORITY
Reset
0xFFFE
31, highest
0xFFFC
30
0xFFFA
29
PC out of range (2)
NMI
NMIIFG
(non)-maskable
Oscillator fault
OFIFG
(non)-maskable
Flash memory access violation
ACCVIFG (1) (3)
(non)-maskable
0xFFF8
28
Comparator_A+
CAIFG
maskable
0xFFF6
27
Watchdog Timer+
WDTIFG
maskable
0xFFF4
26
maskable
0xFFF2
25
maskable
0xFFF0
24
0xFFEE
23
0xFFEC
22
0xFFEA
21
0xFFE8
20
Timer_A3
Timer_A3
(1)
(2)
(3)
(4)
(5)
(6)
8
TACCR0 CCIFG
(4)
TACCR2, TACCR1 CCIFG,
TAIFG (1) (4)
I/O port P2 (eight flags)
P2IFG.0 to P2IFG.7
(1) (4)
maskable
0xFFE6
19
I/O port P1 (eight flags)
P1IFG.0 to P1IFG.7 (1) (4)
maskable
0xFFE4
18
0xFFE2
17
0xFFE0
16
See
(5)
0xFFDE
15
See
(6)
0xFFDC to 0xFFC0
14 to 0, lowest
Multiple source flags
A reset is generated if the CPU tries to fetch instructions from within the module register memory address range (0x0000 to 0x01FF) or
from within unused address range.
(non)-maskable: the individual interrupt-enable bit can disable an interrupt event, but the general interrupt enable cannot.
Interrupt flags are located in the module.
This location is used as bootstrap loader security key (BSLSKEY).
A value of 0xAA55 at this location disables the BSL completely.
A value of 0x0 disables the erasure of the flash if an invalid password is supplied.
The interrupt vectors at addresses 0xFFDC to 0xFFC0 are not used in this device and can be used for regular program code if
necessary.
Copyright © 2004–2011, Texas Instruments Incorporated
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
Special Function Registers
Most interrupt and module enable bits are collected into the lowest address space. Special function register bits
not allocated to a functional purpose are not physically present in the device. Simple software access is provided
with this arrangement.
Legend
rw
rw-0, 1
rw-(0), (1)
Bit can be read and written.
Bit can be read and written. It is Reset or Set by PUC.
Bit can be read and written. It is Reset or Set by POR.
SFR bit is not present in device.
Table 6. Interrupt Enable 1
Address
7
6
00h
WDTIE
OFIE
NMIIE
ACCVIE
5
4
ACCVIE
rw-0
3
2
1
0
NMIIE
OFIE
WDTIE
rw-0
rw-0
rw-0
Watchdog timer interrupt enable. Inactive if watchdog mode is selected. Active if watchdog timer is configured in interval
timer mode.
Oscillator fault interrupt enable
(Non)maskable interrupt enable
Flash access violation interrupt enable
Table 7. Interrupt Enable 2
Address
7
6
7
6
5
4
3
2
1
0
01h
Table 8. Interrupt Flag Register 1
Address
5
02h
WDTIFG
OFIFG
RSTIFG
PORIFG
NMIIFG
4
3
2
1
0
NMIIFG
RSTIFG
PORIFG
OFIFG
WDTIFG
rw-0
rw-(0)
rw-(1)
rw-1
rw-(0)
Set on watchdog timer overflow (in watchdog mode) or security key violation.
Reset on VCC power-up or a reset condition at RST/NMI pin in reset mode.
Flag set on oscillator fault
External reset interrupt flag. Set on a reset condition at RST/NMI pin in reset mode. Reset on VCC power up.
Power-on reset interrupt flag. Set on VCC power up.
Set via RST/NMI pin
Table 9. Interrupt Flag Register 2
Address
7
6
5
4
3
2
1
0
03h
Copyright © 2004–2011, Texas Instruments Incorporated
9
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
Memory Organization
Table 10. Memory Organization
MSP430F2101
MSP430F2111
MSP430F2121
Size
1 KB Flash
2 KB Flash
4 KB Flash
8 KB Flash
Main: interrupt vector
Flash
0xFFFF to 0xFFE0
0xFFFF to 0xFFE0
0xFFFF to 0xFFE0
0xFFFF to 0xFFE0
Main: code memory
Flash
0xFFFF to 0xFC00
0xFFFF to 0xF800
0xFFFF to 0xF000
0xFFFF to 0xE000
Information memory
Size
256 Byte
256 Byte
256 Byte
256 Byte
Flash
0x10FF to 0x1000
0x10FF to 0x1000
0x10FF to 0x1000
0x10FF to 0x1000
Size
1 KB
1 KB
1 KB
1 KB
ROM
0x0FFF to 0x0C00
0x0FFF to 0x0C00
0x0FFF to 0x0C00
0x0FFF to 0x0C00
Size
128 B
128 B
256 Byte
256 Byte
0x027F to 0x0200
0x027F to 0x0200
0x02FF to 0x0200
0x02FF to 0x0200
16-bit
0x01FF to 0x0100
0x01FF to 0x0100
0x01FF to 0x0100
0x01FF to 0x0100
8-bit
0x0FF to 0x010
0x0FF to 0x010
0x0FF to 0x010
0x0FF to 0x010
0x0F to 0x00
0x0F to 0x00
0x0F to 0x00
0x0F to 0x00
Memory
Boot memory
RAM
Peripherals
8-bit SFR
MSP430F2131
Bootstrap Loader (BSL)
The MSP430 bootstrap loader (BSL) enables users to program the flash memory or RAM using a UART serial
interface. Access to theMSP430memoryvia theBSLis protected by user-defined password.Abootstrap loader
security key is provided at address 0FFDEh to disable the BSL completely or to disable the erasure of the flash if
an invalid password is supplied. For complete description of the features of the BSL and its implementation, see
the MSP430 Programming Via the Bootstrap Loader User’s Guide, literature number SLAU319.
Table 11. BSL Keys
BSLKEY
DESCRIPTION
00000h
Erasure of flash disabled if an invalid password is supplied
0AA55h
BSL disabled
any other value
BSL enabled
Table 12. BSL Function Pins
BSL FUNCTION
DW, PW, DGV PACKAGE PINS
RGE PACKAGE PINS
Data transmit
14 - P1.1
14 - P1.1
Data receive
10 - P2.2
8 - P2.2
Flash Memory
The flash memory can be programmed via the JTAG port, the bootstrap loader, or in-system by the CPU. The
CPU can perform single-byte and single-word writes to the flash memory. Features of the flash memory include:
• Flash memory has n segments of main memory and four segments of information memory (A to D) of
64 bytes each. Each segment in main memory is 512 bytes in size.
• Segments 0 to n may be erased in one step, or each segment may be individually erased.
• Segments A to D can be erased individually, or as a group with segments 0 to n.
Segments A to D are also called information memory.
• Segment A contains calibration data. After reset, segment A is protected against programming and erasing. It
can be unlocked, but care should be taken not to erase this segment if the device-specific calibration data is
required.
10
Copyright © 2004–2011, Texas Instruments Incorporated
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
Peripherals
Peripherals are connected to the CPU through data, address, and control buses and can be handled using all
instructions. For complete module descriptions, see the MSP430x2xx Family User's Guide (SLAU144).
Oscillator and System Clock
The clock system is supported by the basic clock module that includes support for a 32768-Hz watch crystal
oscillator, an internal digitally-controlled oscillator (DCO), and a high-frequency crystal oscillator. The basic clock
module is designed to meet the requirements of both low system cost and low power consumption. The internal
DCO provides a fast turn-on clock source and stabilizes in less than 1 µs. The basic clock module provides the
following clock signals:
• Auxiliary clock (ACLK), sourced from a 32768-Hz watch crystal or a high-frequency crystal
• Main clock (MCLK), the system clock used by the CPU
• Sub-Main clock (SMCLK), the sub-system clock used by the peripheral modules
Table 13. DCO Calibration Data, Provided From Factory In Flash Info Memory
Segment A
DCO FREQUENCY
CALIBRATION REGISTER
SIZE
CALBC1_1MHZ
byte
0x010FF
CALBC0_1MHZ
byte
0x010FE
CALBC1_8MHZ
byte
0x010FD
CALBC0_8MHZ
byte
0x010FC
CALBC1_12MHZ
byte
0x010FB
CALBC0_12MHZ
byte
0x010FA
CALBC1_16MHZ
byte
0x010F9
CALBC0_16MHZ
byte
0x010F8
1 MHz
8 MHz
12 MHz
16 MHz
ADDRESS
Brownout
The brownout circuit is implemented to provide the proper internal reset signal to the device during power on and
power off.
Digital I/O
There are two 8-bit I/O ports implemented—ports P1 and P2.
• All individual I/O bits are independently programmable.
• Any combination of input, output, and interrupt condition is possible.
• Edge-selectable interrupt input capability for all eight bits of port P1 and P2.
• Read/write access to port-control registers is supported by all instructions.
• Each I/O has an individually programmable pullup/pulldown resistor.
Watchdog Timer (WDT+)
The primary function of the WDT+ module is to perform a controlled system restart after a software problem
occurs. If the selected time interval expires, a system reset is generated. If the watchdog function is not needed
in an application, the module can be disabled or configured as an interval timer and can generate interrupts at
selected time intervals.
Comparator_A+
The primary function of the comparator_A+ module is to support precision slope analog-to-digital conversions,
battery-voltage supervision, and monitoring of external analog signals.
Copyright © 2004–2011, Texas Instruments Incorporated
11
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
Timer_A3
Timer_A3 is a 16-bit timer/counter with three capture/compare registers. Timer_A3 can support multiple
capture/compares, PWM outputs, and interval timing. Timer_A3 also has extensive interrupt capabilities.
Interrupts may be generated from the counter on overflow conditions and from each of the capture/compare
registers.
Table 14. Timer_A3 Signal Connections
INPUT PIN NUMBER
DW, PW, DGV
RGE
DEVICE INPUT
SIGNAL
13 - P1.0
13 - P1.0
TACLK
TACLK
ACLK
ACLK
SMCLK
SMCLK
MODULE
BLOCK
MODULE
OUTPUT
SIGNAL
Timer
NA
OUTPUT PIN NUMBER
DW, PW, DGV
RGE
9 - P2.1
7 - P2.1
INCLK
INCLK
14 - P1.1
14 - P1.1
TA
CCI0A
14 - P1.1
14 - P1.1
10 - P2.2
8 - P2.2
TA
CCI0B
18 - P1.5
18 - P1.5
VSS
GND
11 - P2.3
10 - P2.3
15 - P1.2
15 - P1.2
19 - P1.6
20 - P1.6
15 - P1.2
16 - P1.3
12
MODULE
INPUT NAME
15 - P1.2
16 - P1.3
VCC
VCC
TA1
CCI1A
CAOUT
(internal)
CCI1B
VSS
GND
CCR0
CCR1
TA
TA1
VCC
VCC
TA2
CCI2A
12 - P2.4
11 - P2.4
ACLK (internal)
CCI2B
16 - P1.3
16 - P1.3
VSS
GND
20 - P1.7
21 - P1.7
VCC
VCC
CCR2
TA2
Copyright © 2004–2011, Texas Instruments Incorporated
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
Peripheral File Map
Table 15. Peripherals With Word Access
MODULE
Timer_A
SHORT NAME
ADDRESS OFFSET
Capture/compare register
REGISTER NAME
TACCR2
0x0176
Capture/compare register
TACCR1
0x0174
Capture/compare register
TACCR0
0x0172
TAR
0x0170
Capture/compare control
TACCTL2
0x0166
Capture/compare control
TACCTL1
0x0164
Capture/compare control
TACCTL0
0x0162
Timer_A3 register
Timer_A3 control
TACTL
0x0160
TAIV
0x012E
Flash control 3
FCTL3
0x012C
Flash control 2
FCTL2
0x012A
Flash control 1
FCTL1
0x0128
WDTCTL
0x0120
SHORT NAME
ADDRESS OFFSET
CAPD
0x005B
CACTL2
0x005A
Timer_A3 interrupt vector
Flash Memory
Watchdog Timer+
Watchdog/timer control
Table 16. Peripherals With Byte Access
MODULE
Comparator_A+
REGISTER NAME
Comparator_A port disable
Comparator_A control 2
Comparator_A control 1
Basic Clock
Port P2
CACTL1
0x0059
Basic clock system control 3
BCSCTL3
0x0053
Basic clock system control 2
BCSCTL2
0x0058
Basic clock system control 1
BCSCTL1
0x0057
DCO clock frequency control
DCOCTL
0x0056
Port P2 resistor enable
P2REN
0x002F
Port P2 selection
P2SEL
0x002E
P2IE
0x002D
Port P2 interrupt edge select
P2IES
0x002C
Port P2 interrupt flag
P2IFG
0x002B
Port P2 direction
P2DIR
0x002A
Port P2 output
P2OUT
0x0029
P2IN
0x0028
Port P1 resistor enable
P1REN
0x0027
Port P1 selection
P1SEL
0x0026
P1IE
0x0025
Port P1 interrupt edge select
P1IES
0x0024
Port P1 interrupt flag
P1IFG
0x0023
Port P1 direction
P1DIR
0x0022
Port P1 output
P1OUT
0x0021
Port P1 input
P1IN
0x0020
SFR interrupt flag 2
IFG2
0x0003
SFR interrupt flag 1
IFG1
0x0002
SFR interrupt enable 2
IE2
0x0001
SFR interrupt enable 1
IE1
0x0000
Port P2 interrupt enable
Port P2 input
Port P1
Port P1 interrupt enable
Special Function
Copyright © 2004–2011, Texas Instruments Incorporated
13
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
Absolute Maximum Ratings (1)
Voltage applied at VCC to VSS
Voltage applied to any pin
-0.3 V to 4.1 V
(2)
-0.3 V to (VCC + 0.3 V)
±2 mA
Diode current at any device terminal
Storage temperature, Tstg
(1)
(3)
Unprogrammed device
-55°C to 150°C
Programmed device
-55°C to 150°C
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltages referenced to VSS. The JTAG fuse-blow voltage, VFB, is allowed to exceed the absolute maximum rating. The voltage is
applied to the TEST pin when blowing the JTAG fuse.
Higher temperature may be applied during board soldering process according to the current JEDEC J-STD-020 specification with peak
reflow temperatures not higher than classified on the device label on the shipping boxes or reels.
(2)
(3)
Recommended Operating Conditions (1)
MIN
VCC
Supply voltage, AVCC = DVCC = VCC
VSS
Supply voltage, AVSS = DVSS = VSS
TA
Operating free-air temperature
fSYSTEM
Processor frequency (maximum MCLK
frequency) (2) (1)
(see Figure 1)
(1)
(2)
NOM
MAX
During program execution
1.8
3.6
During flash memory programming
2.2
3.6
0
UNIT
V
V
I version
-40
85
T version
-40
105
VCC = 1.8 V, Duty cycle = 50% ±10%
0
6
VCC = 2.7 V, Duty cycle = 50% ±10%
0
12
VCC ≥ 3.3 V, Duty cycle = 50% ±10%
0
16
°C
MHz
Modules might have a different maximum input clock specification. See the specification of the respective module in this data sheet.
The MSP430 CPU is clocked directly with MCLK. Both the high and low phase of MCLK must not exceed the pulse width of the
specified maximum frequency.
Legend :
System Frequency −MHz
16 MHz
Supply voltage range
during flash memory
programming
12 MHz
Supply voltage range
during program execution
6 MHz
1.8 V
2.2 V
2.7 V
3.3 V
3.6 V
Supply Voltage − V
NOTE: Minimum processor frequency is defined by system clock. Flash program or erase operations require a minimum VCC
of 2.2 V.
Figure 1. Operating Area
14
Copyright © 2004–2011, Texas Instruments Incorporated
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
Active Mode Supply Current (into DVCC + AVCC ) Excluding External Current
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (1) (2)
PARAMETER
IAM,1MHz
IAM,1MHz
IAM,4kHz
IAM,100kHz
(1)
(2)
TEST CONDITIONS
TA
VCC
MIN
TYP
MAX
2.2 V
250
300
Active mode (AM)
current (1 MHz)
fDCO = fMCLK = fSMCLK = 1 MHz,
fACLK = 32768 Hz,
Program executes in flash,
BCSCTL1 = CALBC1_1MHZ,
DCOCTL = CALDCO_1MHZ,
CPUOFF = 0, SCG0 = 0, SCG1 = 0,
OSCOFF = 0
3V
350
410
2.2 V
200
Active mode (AM)
current (1 MHz)
fDCO = fMCLK = fSMCLK = 1 MHz,
fACLK = 32768 Hz,
Program executes in RAM,
BCSCTL1 = CALBC1_1MHZ,
DCOCTL = CALDCO_1MHZ,
CPUOFF = 0, SCG0 = 0, SCG1 = 0,
OSCOFF = 0
3V
300
Active mode (AM)
current (4 kHz)
fMCLK = fSMCLK = fACLK = 32768 Hz / 8
= 4096 Hz,
fDCO = 0 Hz,
Program executes in flash,
SELMx = 11, SELS = 1,
DIVMx = DIVSx = DIVAx = 11,
CPUOFF = 0, SCG0 = 1, SCG1 = 0,
OSCOFF = 0
-40°C to 85°C
3
3V
105°C
µA
µA
5
6
-40°C to 85°C
fMCLK = fSMCLK = fDCO(0, 0) ≈ 100 kHz,
fACLK = 0 Hz,
Program executes in flash,
RSELx = 0, DCOx = 0, CPUOFF = 0,
SCG0 = 0, SCG1 = 0, OSCOFF = 1
Active mode (AM)
current (100 kHz)
2
2.2 V
105°C
UNIT
9
µA
9
2.2 V
60
85
3V
72
95
µA
All inputs are tied to 0 V or VCC. Outputs do not source or sink any current.
The currents are characterized with a Micro Crystal CC4V-T1A SMD crystal with a load capacitance of 9 pF. The internal and external
load capacitance is chosen to closely match the required 9 pF.
Typical Characteristics - Active-Mode Supply Current (Into VCC)
ACTIVE-MODE CURRENT
vs
SUPPLY VOLTAGE
TA = 25°C
ACTIVE-MODE CURRENT
vs
DCO FREQUENCY
7.0
5.0
Active ModeCurrent – mA
Active Mode Current – mA
5.0
fDCO = 16 MHz
6.0
fDCO = 12 MHz
4.0
fDCO = 8 MHz
3.0
2.0
4.0
TA = 85°C
TA = 25°C
3.0
VCC = 3 V
2.0
TA = 85°C
TA = 25°C
1.0
VCC = 2.2 V
1.0
fDCO = 1 MHz
0.0
1.5
0.0
2.0
2.5
3.0
VCC – Supply Voltage – V
Figure 2.
Copyright © 2004–2011, Texas Instruments Incorporated
3.5
4.0
0
4
8
12
16
fDCO – DCO Frequency – MHz
Figure 3.
15
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
Low-Power-Mode Supply Currents (Into VCC ) Excluding External Current
(1) (2)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
ILPM0,1MHz
ILPM0,100kHz
ILPM2
TEST CONDITIONS
TA
VCC
65
80
Low-power mode 0
(LPM0) current (3)
3V
85
100
2.2 V
37
48
Low-power mode 0
(LPM0) current (3)
fMCLK = 0 MHz,
fSMCLK = fDCO(0, 0) ≈ 100 kHz,
fACLK = 0 Hz,
RSELx = 0, DCOx = 0,
CPUOFF = 1, SCG0 = 0, SCG1 = 0,
OSCOFF = 1
3V
41
52
22
29
Low-power mode 2
(LPM2) current (4)
fMCLK = fSMCLK = 0 MHz,
fDCO = 1 MHz, fACLK = 32768 Hz,
BCSCTL1 = CALBC1_1MHZ,
DCOCTL = CALDCO_1MHZ,
CPUOFF = 1, SCG0 = 0, SCG1 = 1,
OSCOFF = 0
-40°C to 85°C
105°C
2.2 V
-40°C to 85°C
105°C
3V
Low-power mode 3
(LPM3) current (4)
fDCO = fMCLK = fSMCLK = 0 MHz,
fACLK = 32768 Hz,
CPUOFF = 1, SCG0 = 1, SCG1 = 1,
OSCOFF = 0
(3)
(4)
(5)
16
Low-power mode 4
(LPM4) current (5)
fDCO = fMCLK = fSMCLK = 0 MHz,
fACLK = 0 Hz,
CPUOFF = 1, SCG0 = 1, SCG1 = 1,
OSCOFF = 1
32
1
2.3
105°C
3
6
-40°C
0.9
1.2
0.9
1.2
1.6
2.8
3V
105°C
3
7
-40°C
0.1
0.5
0.1
0.5
0.8
1.9
2
4
25°C
85°C
105°C
2.2 V/3 V
µA
µA
1.2
1.6
25°C
µA
34
0.7
2.2 V
UNIT
31
25
0.7
85°C
85°C
(1)
(2)
MAX
2.2 V
25°C
ILPM4
TYP
fMCLK = 0 MHz,
fSMCLK = fDCO = 1 MHz,
fACLK = 32768 Hz,
BCSCTL1 = CALBC1_1MHZ,
DCOCTL = CALDCO_1MHZ,
CPUOFF = 1, SCG0 = 0, SCG1 = 0,
OSCOFF = 0
-40°C
ILPM3,LFXT1
MIN
µA
µA
All inputs are tied to 0 V or VCC. Outputs do not source or sink any current.
The currents are characterized with a Micro Crystal CC4V-T1A SMD crystal with a load capacitance of 9 pF. The internal and external
load capacitance is chosen to closely match the required 9 pF.
Current for brownout and WDT clocked by SMCLK included.
Current for brownout and WDT clocked by ACLK included.
Current for brownout included.
Copyright © 2004–2011, Texas Instruments Incorporated
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
Schmitt-Trigger Inputs (Ports P1, P2)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
VIT+
TEST CONDITIONS
Positive-going input threshold voltage
VCC
Negative-going input threshold voltage
Vhys
Input voltage hysteresis (VIT+ - VIT- )
RPull
Pullup/pulldown resistor
For pullup: VIN = VSS,
For pulldown: VIN = VCC
CI
Input capacitance
VIN = VSS or VCC
TYP
MAX
0.45 VCC
0.75 VCC
1
1.65
1.35
2.25
0.25 VCC
0.55 VCC
2.2 V
0.55
1.20
3V
0.75
1.65
2.2 V
0.2
1
3V
0.3
1
2.2 V
3V
VIT-
MIN
20
35
UNIT
V
V
V
50
kΩ
5
pF
Inputs (Ports P1, P2)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
t(int)
(1)
External interrupt timing
TEST CONDITIONS
VCC
Port P1, P2: P1.x to P2.x, External trigger pulse width to
set interrupt flag (1)
2.2 V/3 V
MIN
MAX
UNIT
20
ns
An external signal sets the interrupt flag every time the minimum interrupt pulse width t(int) is met. It may be set with trigger signals
shorter than t(int).
Leakage Current (Ports P1, P2)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
Ilkg(Px.y)
(1)
(2)
High-impedance leakage current
TEST CONDITIONS
(1) (2)
VCC
2.2 V/3 V
MIN
MAX
UNIT
±50
nA
The leakage current is measured with VSS or VCC applied to the corresponding pin(s), unless otherwise noted.
The leakage of the digital port pins is measured individually. The port pin is selected for input and the pullup/pulldown resistor is
disabled.
Copyright © 2004–2011, Texas Instruments Incorporated
17
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
Outputs (Ports P1, P2)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
IOH(max) = -1.5 mA
VOH
High-level output voltage
2.2 V
IOH(max) = -6 mA (2)
IOH(max) = -1.5 mA (1)
3V
IOH(max) = -6 mA (2)
IOL(max) = 1.5 mA
VOL
Low-level output voltage
(2)
MIN
MAX
VCC - 0.25
VCC
VCC - 0.6
VCC
VCC - 0.25
VCC
VCC - 0.6
VCC
VSS
VSS + 0.25
(1)
2.2 V
IOL(max) = 6 mA (2)
IOL(max) = 1.5 mA (1)
3V
IOL(max) = 6 mA (2)
(1)
VCC
(1)
VSS
VSS + 0.6
VSS
VSS + 0.25
VSS
VSS + 0.6
UNIT
V
V
The maximum total current, IOH(max) and IOL(max), for all outputs combined, should not exceed ±12 mA to hold the maximum voltage drop
specified.
The maximum total current, IOH(max) and IOL(max), for all outputs combined, should not exceed ±48 mA to hold the maximum voltage drop
specified.
Output Frequency (Ports P1, P2)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VCC
fPx.y
Port output frequency (with load)
P1.4/SMCLK, CL = 20 pF, RL = 1 kΩ (1) (2)
fPort_CLK
Clock output frequency
P2.0/ACLK, P1.4/SMCLK, CL = 20 pF (2)
(1)
(2)
18
MIN
MAX
2.2 V
10
3V
12
2.2 V
12
3V
16
UNIT
MHz
MHz
Alternatively, a resistive divider with two 0.5-kΩ resistors between VCC and VSS is used as load. The output is connected to the center
tap of the divider.
The output voltage reaches at least 10% and 90% VCC at the specified toggle frequency.
Copyright © 2004–2011, Texas Instruments Incorporated
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
Typical Characteristics - Outputs
One output loaded at a time.
TYPICAL LOW-LEVEL OUTPUT CURRENT
vs
LOW-LEVEL OUTPUT VOLTAGE
TYPICAL LOW-LEVEL OUTPUT CURRENT
vs
LOW-LEVEL OUTPUT VOLTAGE
50.0
VCC = 2.2 V
P2.4
TA = 25°C
20.0
I OL − Typical Low-Level Output Current − mA
I OL − Typical Low-Level Output Current − mA
25.0
TA = 85°C
15.0
10.0
5.0
0.0
0.0
0.5
1.0
1.5
2.0
VCC = 3 V
P2.4
40.0
TA = 85°C
30.0
20.0
10.0
0.0
0.0
2.5
VOL − Low-Level Output Voltage − V
0.5
1.0
1.5
2.0
2.5
3.0
Figure 4.
Figure 5.
TYPICAL HIGH-LEVEL OUTPUT CURRENT
vs
HIGH-LEVEL OUTPUT VOLTAGE
TYPICAL HIGH-LEVEL OUTPUT CURRENT
vs
HIGH-LEVEL OUTPUT VOLTAGE
0.0
I OH − Typical High-Level Output Current − mA
VCC = 2.2 V
P2.4
−5.0
−10.0
−15.0
−20.0
−25.0
0.0
3.5
VOL − Low-Level Output Voltage − V
0.0
I OH − Typical High-Level Output Current − mA
TA = 25°C
TA = 85°C
TA = 25°C
0.5
1.0
1.5
2.0
VOH − High-Level Output Voltage − V
Figure 6.
Copyright © 2004–2011, Texas Instruments Incorporated
2.5
VCC = 3 V
P2.4
−10.0
−20.0
−30.0
−40.0
−50.0
0.0
TA = 85°C
TA = 25°C
0.5
1.0
1.5
2.0
2.5
3.0
3.5
VOH − High-Level Output Voltage − V
Figure 7.
19
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
POR/Brownout Reset (BOR) (1) (2)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VCC(start)
See Figure 8
dVCC /dt ≤ 3 V/s
V(B_IT-)
See Figure 8 through
Figure 10
dVCC /dt ≤ 3 V/s
Vhys(B_IT-)
See Figure 8
dVCC /dt ≤ 3 V/s
td(BOR)
See Figure 8
t(reset)
Pulse length needed at
RST/NMI pin to accepted
reset internally
(1)
(2)
TA
VCC
MIN
TYP
MAX
0.7 ×
V(B_IT-)
V
1.71
-40°C to 85°C
70
130
180
105°C
70
130
210
2000
2.2 V/3 V
2
UNIT
V
mV
µs
µs
The current consumption of the brownout module is already included in the ICC current consumption data. The voltage level
V(B_IT-) + Vhys(B_IT-) is ≤ 1.8 V.
During power up, the CPU begins code execution following a period of td(BOR) after VCC = V(B_IT-) + Vhys(B_IT-). The default DCO settings
must not be changed until VCC ≥ VCC(min), where VCC(min) is the minimum supply voltage for the desired operating frequency.
VCC
Vhys(B_IT−)
V(B_IT−)
VCC(start)
1
0
t d(BOR)
Figure 8. POR/Brownout Reset (BOR) vs Supply Voltage
20
Copyright © 2004–2011, Texas Instruments Incorporated
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
Typical Characteristics - POR/Brownout Reset (BOR)
VCC
3V
2
VCC(drop) − V
VCC = 3 V
Typical Conditions
t pw
1.5
1
VCC(drop)
0.5
0
0.001
1
1000
1 ns
t pw − Pulse Width − µs
1 ns
t pw − Pulse Width − µs
Figure 9. VCC(drop) Level With a Square Voltage Drop to Generate a POR/Brownout Signal
VCC
2
t pw
3V
VCC(drop) − V
VCC = 3 V
1.5
Typical Conditions
1
VCC(drop)
0.5
0
0.001
tf = tr
1
t pw − Pulse Width − µs
1000
tf
tr
t pw − Pulse Width − µs
Figure 10. VCC(drop) Level With a Triangle Voltage Drop to Generate a POR/Brownout Signal
Copyright © 2004–2011, Texas Instruments Incorporated
21
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
Main DCO Characteristics
•
•
•
All ranges selected by RSELx overlap with RSELx + 1: RSELx = 0 overlaps RSELx = 1, ... RSELx = 14
overlaps RSELx = 15.
DCO control bits DCOx have a step size as defined by parameter SDCO.
Modulation control bits MODx select how often fDCO(RSEL,DCO+1) is used within the period of 32 DCOCLK
cycles. The frequency fDCO(RSEL,DCO) is used for the remaining cycles. The frequency is an average equal to:
faverage =
32 × fDCO(RSEL,DCO) × fDCO(RSEL,DCO+1)
MOD × fDCO(RSEL,DCO) + (32 – MOD) × fDCO(RSEL,DCO+1)
DCO Frequency
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VCC
MIN
TYP
MAX
RSELx < 14
1.8
3.6
RSELx = 14
2.2
3.6
UNIT
VCC
Supply voltage range
3.0
3.6
fDCO(0,0)
DCO frequency (0, 0)
RSELx = 0, DCOx = 0, MODx = 0
2.2 V/3 V
0.06
0.14
MHz
fDCO(0,3)
DCO frequency (0, 3)
RSELx = 0, DCOx = 3, MODx = 0
2.2 V/3 V
0.07
0.17
MHz
fDCO(1,3)
DCO frequency (1, 3)
RSELx = 1, DCOx = 3, MODx = 0
2.2 V/3 V
0.10
0.20
MHz
fDCO(2,3)
DCO frequency (2, 3)
RSELx = 2, DCOx = 3, MODx = 0
2.2 V/3 V
0.14
0.28
MHz
fDCO(3,3)
DCO frequency (3, 3)
RSELx = 3, DCOx = 3, MODx = 0
2.2 V/3 V
0.20
0.40
MHz
fDCO(4,3)
DCO frequency (4, 3)
RSELx = 4, DCOx = 3, MODx = 0
2.2 V/3 V
0.28
0.54
MHz
fDCO(5,3)
DCO frequency (5, 3)
RSELx = 5, DCOx = 3, MODx = 0
2.2 V/3 V
0.39
0.77
MHz
fDCO(6,3)
DCO frequency (6, 3)
RSELx = 6, DCOx = 3, MODx = 0
2.2 V/3 V
0.54
1.06
MHz
fDCO(7,3)
DCO frequency (7, 3)
RSELx = 7, DCOx = 3, MODx = 0
2.2 V/3 V
0.80
1.50
MHz
fDCO(8,3)
DCO frequency (8, 3)
RSELx = 8, DCOx = 3, MODx = 0
2.2 V/3 V
1.10
2.10
MHz
fDCO(9,3)
DCO frequency (9, 3)
RSELx = 9, DCOx = 3, MODx = 0
2.2 V/3 V
1.60
3.00
MHz
fDCO(10,3)
DCO frequency (10, 3)
RSELx = 10, DCOx = 3, MODx = 0
2.2 V/3 V
2.50
4.30
MHz
fDCO(11,3)
DCO frequency (11, 3)
RSELx = 11, DCOx = 3, MODx = 0
2.2 V/3 V
3.00
5.50
MHz
fDCO(12,3)
DCO frequency (12, 3)
RSELx = 12, DCOx = 3, MODx = 0
2.2 V/3 V
4.30
7.30
MHz
fDCO(13,3)
DCO frequency (13, 3)
RSELx = 13, DCOx = 3, MODx = 0
2.2 V/3 V
6.00
9.60
MHz
fDCO(14,3)
DCO frequency (14, 3)
RSELx = 14, DCOx = 3, MODx = 0
2.2 V/3 V
8.60
13.9
MHz
fDCO(15,3)
DCO frequency (15, 3)
RSELx = 15, DCOx = 3, MODx = 0
3V
12.0
18.5
MHz
fDCO(15,7)
DCO frequency (15, 7)
RSELx = 15, DCOx = 7, MODx = 0
3V
16.0
26.0
MHz
SRSEL
Frequency step between
range RSEL and RSEL+1
SRSEL = fDCO(RSEL+1,DCO) /fDCO(RSEL,DCO)
2.2 V/3 V
1.55
ratio
SDCO
Frequency step between tap
DCO and DCO+1
SDCO = fDCO(RSEL,DCO+1) /fDCO(RSEL,DCO)
2.2 V/3 V
1.05
1.08
1.12
ratio
Duty cycle
Measured at P1.4/SMCLK
2.2 V/3 V
40
50
60
RSELx = 15
22
V
%
Copyright © 2004–2011, Texas Instruments Incorporated
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
Calibrated DCO Frequencies - Tolerance at Calibration
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
Frequency tolerance at calibration
TA
VCC
MIN
TYP
MAX
UNIT
25°C
3V
-1
±0.2
+1
25°C
3V
0.990
1
1.010
MHz
%
fCAL(1MHz)
1-MHz calibration value
BCSCTL1 = CALBC1_1MHZ,
DCOCTL = CALDCO_1MHZ,
Gating time: 5 ms
fCAL(8MHz)
8-MHz calibration value
BCSCTL1 = CALBC1_8MHZ,
DCOCTL = CALDCO_8MHZ,
Gating time: 5 ms
25°C
3V
7.920
8
8.080
MHz
fCAL(12MHz)
12-MHz calibration value
BCSCTL1 = CALBC1_12MHZ,
DCOCTL = CALDCO_12MHZ,
Gating time: 5 ms
25°C
3V
11.88
12
12.12
MHz
fCAL(16MHz)
16-MHz calibration value
BCSCTL1 = CALBC1_16MHZ,
DCOCTL = CALDCO_16MHZ,
Gating time: 2 ms
25°C
3V
15.84
16
16.16
MHz
MAX
UNIT
Calibrated DCO Frequencies - Tolerance Over Temperature 0°C to 85°C
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
fCAL(1MHz)
fCAL(8MHz)
fCAL(12MHz)
fCAL(16MHz)
TA
VCC
1-MHz tolerance over
temperature
0°C to 85°C
3V
-2.5
±0.5
+2.5
%
8-MHz tolerance over
temperature
0°C to 85°C
3V
-2.5
±1
+2.5
%
12-MHz tolerance over
temperature
0°C to 85°C
3V
-2.5
±1
+2.5
%
16-MHz tolerance over
temperature
0°C to 85°C
3V
-3
±2
+3
%
2.2 V
0.97
1
1.03
3V
0.975
1
1.025
3.6 V
0.97
1
1.03
2.2 V
7.76
8
8.4
3V
7.8
8
8.2
3.6 V
7.6
8
8.24
2.2 V
11.7
12
12.3
3V
11.7
12
12.3
3.6 V
11.7
12
12.3
3V
15.52
16
16.48
15
16
16.48
1-MHz calibration value
8-MHz calibration value
12-MHz calibration value
16-MHz calibration value
TEST CONDITIONS
BCSCTL1 = CALBC1_1MHZ,
DCOCTL = CALDCO_1MHZ,
Gating time: 5 ms
0°C to 85°C
BCSCTL1 = CALBC1_8MHZ,
DCOCTL = CALDCO_8MHZ,
Gating time: 5 ms
0°C to 85°C
BCSCTL1 = CALBC1_12MHZ,
DCOCTL = CALDCO_12MHZ,
Gating time: 5 ms
0°C to 85°C
BCSCTL1 = CALBC1_16MHZ,
DCOCTL = CALDCO_16MHZ,
Gating time: 2 ms
0°C to 85°C
Copyright © 2004–2011, Texas Instruments Incorporated
3.6 V
MIN
TYP
MHz
MHz
MHz
MHz
23
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
Calibrated DCO Frequencies - Tolerance Over Supply Voltage VCC
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA
VCC
MIN
TYP
MAX
1-MHz tolerance over VCC
25°C
8-MHz tolerance over VCC
25°C
12-MHz tolerance over VCC
16-MHz tolerance over VCC
UNIT
1.8 V to 3.6 V
-3
±2
+3
%
1.8 V to 3.6 V
-3
±2
+3
%
25°C
2.2 V to 3.6 V
-3
±2
+3
%
25°C
3 V to 3.6 V
-3
±2
+3
%
fCAL(1MHz)
1-MHz calibration value
BCSCTL1 = CALBC1_1MHZ,
DCOCTL = CALDCO_1MHZ,
Gating time: 5 ms
25°C
1.8 V to 3.6 V
0.97
1
1.03
MHz
fCAL(8MHz)
8-MHz calibration value
BCSCTL1 = CALBC1_8MHZ,
DCOCTL = CALDCO_8MHZ,
Gating time: 5 ms
25°C
1.8 V to 3.6 V
7.76
8
8.24
MHz
fCAL(12MHz)
12-MHz calibration value
BCSCTL1 = CALBC1_12MHZ,
DCOCTL = CALDCO_12MHZ,
Gating time: 5 ms
25°C
2.2 V to 3.6 V
11.64
12
12.36
MHz
fCAL(16MHz)
16-MHz calibration value
BCSCTL1 = CALBC1_16MHZ,
DCOCTL = CALDCO_16MHZ,
Gating time: 2 ms
25°C
3 V to 3.6 V
15
16
16.48
MHz
MIN
TYP
MAX
UNIT
Calibrated DCO Frequencies - Overall Tolerance
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TA
VCC
1-MHz tolerance
overall
I: -40°C to 85°C
T: -40°C to 105°C
1.8 V to 3.6 V
-5
±2
+5
%
8-MHz tolerance
overall
I: -40°C to 85°C
T: -40°C to 105°C
1.8 V to 3.6 V
-5
±2
+5
%
12-MHz
tolerance overall
I: -40°C to 85°C
T: -40°C to 105°C
2.2 V to 3.6 V
-5
±2
+5
%
16-MHz
tolerance overall
I: -40°C to 85°C
T: -40°C to 105°C
3 V to 3.6 V
-6
±3
+6
%
fCAL(1MHz)
BCSCTL1 = CALBC1_1MHZ,
1-MHz
DCOCTL = CALDCO_1MHZ,
calibration value
Gating time: 5 ms
I: -40°C to 85°C
T: -40°C to 105°C
1.8 V to 3.6 V
0.95
1
1.05
MHz
fCAL(8MHz)
BCSCTL1 = CALBC1_8MHZ,
8-MHz
DCOCTL = CALDCO_8MHZ,
calibration value
Gating time: 5 ms
I: -40°C to 85°C
T: -40°C to 105°C
1.8 V to 3.6 V
7.6
8
8.4
MHz
fCAL(12MHz)
BCSCTL1 = CALBC1_12MHZ,
12-MHz
DCOCTL = CALDCO_12MHZ,
calibration value
Gating time: 5 ms
I: -40°C to 85°C
T: -40°C to 105°C
2.2 V to 3.6 V
11.4
12
12.6
MHz
fCAL(16MHz)
BCSCTL1 = CALBC1_16MHZ,
16-MHz
DCOCTL = CALDCO_16MHZ,
calibration value
Gating time: 2 ms
I: -40°C to 85°C
T: -40°C to 105°C
3 V to 3.6 V
15
16
17
MHz
24
TEST CONDITIONS
Copyright © 2004–2011, Texas Instruments Incorporated
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
Typical Characteristics - Calibrated 1-MHz DCO Frequency
CALIBRATED 1-MHz FREQUENCY
vs
TEMPERATURE
CALIBRATED 1-MHz FREQUENCY
vs
SUPPLY VOLTAGE
1.03
1.03
1.02
1.02
1.00
VCC = 3 V
VCC = 2.2 V
0.99
Frequency – MHz
Frequency – MHz
VCC = 1.8 V
1.01
1.01
TA = 105°C
TA = 85°C
1.00
TA = 25°C
0.99
VCC = 3.6 V
TA = -40°C
0.98
0.97
-50
0.98
-25
0
25
50
TA – Temperature – °C
Figure 11.
Copyright © 2004–2011, Texas Instruments Incorporated
75
100
0.97
1.5
2.0
2.5
3.0
3.5
4.0
VCC – Supply Voltage – V
Figure 12.
25
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
Wake-Up From Lower-Power Modes (LPM3/4)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VCC
MIN
TYP
BCSCTL1 = CALBC1_1MHZ,
DCOCTL = CALDCO_1MHZ
tDCO,LPM3/4
(1)
(2)
UNIT
2
BCSCTL1 = CALBC1_8MHZ,
DCO clock wake-up time DCOCTL = CALDCO_8MHZ
from LPM3/4 (1)
BCSCTL1 = CALBC1_12MHZ,
DCOCTL = CALDCO_12MHZ
2.2 V/3 V
1.5
µs
1
BCSCTL1 = CALBC1_16MHZ,
DCOCTL = CALDCO_16MHZ
tCPU,LPM3/4
MAX
3V
CPU wake-up time from
LPM3/4 (2)
1
1 / fMCLK +
tClock,LPM3/4
The DCO clock wake-up time is measured from the edge of an external wake-up signal (for example, a port interrupt) to the first clock
edge observable externally on a clock pin (MCLK or SMCLK).
Parameter applicable only if DCOCLK is used for MCLK.
Typical Characteristics - DCO Clock Wake-Up Time From LPM3/4
DCO WAKE-UP TIME FROM LPM3
vs
DCO FREQUENCY
DCO Wake Time − µs
10.00
RSELx = 0 to 11
RSELx = 12 to 15
1.00
0.10
0.10
1.00
10.00
DCO Frequency − MHz
Figure 13.
26
Copyright © 2004–2011, Texas Instruments Incorporated
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
Crystal Oscillator LFXT1, Low-Frequency Mode (1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
fLFXT1,LF
LFXT1 oscillator crystal
frequency, LF mode 0, 1
fLFXT1,LF,logic
LFXT1 oscillator logic level
square wave input frequency, XTS = 0, LFXT1Sx = 3
LF mode
OALF
Oscillation allowance for
LF crystals
CL,eff
fFault,LF
(1)
(2)
(3)
(4)
Integrated effective load
capacitance, LF mode (2)
XTS = 0, LFXT1Sx = 0 or 1
VCC
MIN
1.8 V to 3.6 V
1.8 V to 3.6 V
TYP
MAX
32768
10000
32768
XTS = 0, LFXT1Sx = 0,
fLFXT1,LF = 32768 Hz, CL,eff = 6 pF
500
XTS = 0, LFXT1Sx = 0,
fLFXT1,LF = 32768 Hz, CL,eff = 12 pF
200
UNIT
Hz
50000
Hz
kΩ
XTS = 0, XCAPx = 0
1
XTS = 0, XCAPx = 1
5.5
XTS = 0, XCAPx = 2
8.5
XTS = 0, XCAPx = 3
11
Duty cycle, LF mode
XTS = 0, Measured at P2.0/ACLK,
fLFXT1,LF = 32768 Hz
2.2 V/3 V
30
Oscillator fault frequency,
LF mode (3)
XTS = 0, LFXT1Sx = 3 (4)
2.2 V/3 V
10
50
pF
70
%
10000
Hz
To improve EMI on the XT1 oscillator, the following guidelines should be observed.
(a) Keep the trace between the device and the crystal as short as possible.
(b) Design a good ground plane around the oscillator pins.
(c) Prevent crosstalk from other clock or data lines into oscillator pins XIN and XOUT.
(d) Avoid running PCB traces underneath or adjacent to the XIN and XOUT pins.
(e) Use assembly materials and praxis to avoid any parasitic load on the oscillator XIN and XOUT pins.
(f) If conformal coating is used, ensure that it does not induce capacitive/resistive leakage between the oscillator pins.
(g) Do not route the XOUT line to the JTAG header to support the serial programming adapter as shown in other documentation. This
signal is no longer required for the serial programming adapter.
Includes parasitic bond and package capacitance (approximately 2 pF per pin).
Because the PCB adds additional capacitance, it is recommended to verify the correct load by measuring the ACLK frequency. For a
correct setup, the effective load capacitance should always match the specification of the crystal that is used.
Frequencies below the MIN specification set the fault flag. Frequencies above the MAX specification do not set the fault flag.
Frequencies in between might set the flag.
Measured with logic-level input frequency but also applies to operation with crystals.
Copyright © 2004–2011, Texas Instruments Incorporated
27
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
Crystal Oscillator LFXT1, High-Frequency Mode (1)
PARAMETER
VCC
MIN
XTS = 1, LFXT1Sx = 0
1.8 V to 3.6 V
LFXT1 oscillator crystal
frequency, HF mode 1
XTS = 1, LFXT1Sx = 1
LFXT1 oscillator crystal
frequency, HF mode 2
XTS = 1, LFXT1Sx = 2
fLFXT1,HF0
LFXT1 oscillator crystal
frequency, HF mode 0
fLFXT1,HF1
fLFXT1,HF2
TEST CONDITIONS
MAX
UNIT
0.4
1
MHz
1.8 V to 3.6 V
1
4
MHz
1.8 V to 3.6 V
2
10
2.2 V to 3.6 V
2
12
3 V to 3.6 V
fLFXT1,HF,logic
OAHF
CL,eff
LFXT1 oscillator logic-level
square-wave input
frequency, HF mode
Oscillation allowance for HF
crystals (see Figure 14 and
Figure 15)
Integrated effective load
capacitance, HF mode (2)
(1)
(2)
(3)
(4)
(5)
28
Oscillator fault frequency
2
16
1.8 V to 3.6 V
0.4
10
2.2 V to 3.6 V
0.4
12
3 V to 3.6 V
0.4
16
XTS = 1, LFXT1Sx = 0,
fLFXT1,HF = 1 MHz, CL,eff = 15 pF
2700
XTS = 1, LFXT1Sx = 1,
fLFXT1,HF = 4 MHz, CL,eff = 15 pF
800
XTS = 1, LFXT1Sx = 2,
fLFXT1,HF = 16 MHz, CL,eff = 15 pF
300
XTS = 1 (3)
XTS = 1, Measured at P2.0/ACLK,
fLFXT1,HF = 10 MHz
Duty cycle, HF mode
fFault,HF
XTS = 1, LFXT1Sx = 3
XTS = 1, Measured at P2.0/ACLK,
fLFXT1,HF = 16 MHz
(4)
TYP
XTS = 1, LFXT1Sx = 3 (5)
MHz
Ω
1
pF
40
50
60
40
50
60
2.2 V/3 V
2.2 V/3 V
MHz
%
30
300
kHz
To improve EMI on the XT2 oscillator the following guidelines should be observed:
(a) Keep the trace between the device and the crystal as short as possible.
(b) Design a good ground plane around the oscillator pins.
(c) Prevent crosstalk from other clock or data lines into oscillator pins XIN and XOUT.
(d) Avoid running PCB traces underneath or adjacent to the XIN and XOUT pins.
(e) Use assembly materials and praxis to avoid any parasitic load on the oscillator XIN and XOUT pins.
(f) If conformal coating is used, ensure that it does not induce capacitive/resistive leakage between the oscillator pins.
(g) Do not route the XOUT line to the JTAG header to support the serial programming adapter as shown in other documentation. This
signal is no longer required for the serial programming adapter.
Includes parasitic bond and package capacitance (approximately 2 pF per pin). Because the PCB adds additional capacitance, it is
recommended to verify the correct load by measuring the ACLK frequency. For a correct setup, the effective load capacitance should
always match the specification of the used crystal.
Requires external capacitors at both terminals. Values are specified by crystal manufacturers.
Frequencies below the MIN specification set the fault flag, frequencies above the MAX specification do not set the fault flag, and
frequencies in between might set the flag.
Measured with logic-level input frequency, but also applies to operation with crystals.
Copyright © 2004–2011, Texas Instruments Incorporated
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
Typical Characteristics - LFXT1 Oscillator in HF Mode (XTS = 1)
OSCILLATION ALLOWANCE
vs
CRYSTAL FREQUENCY
CL,eff = 15 pF, TA = 25°C
OSCILLATOR SUPPLY CURRENT
vs
CRYSTAL FREQUENCY
CL,eff = 15 pF, TA = 25°C
800
100000
LFXT1Sx = 3
XT Oscillator Supply Current – µA
Oscillation Allowance – W
700
10000
1000
LFXT1Sx = 3
100
LFXT1Sx = 1
LFXT1Sx = 2
600
500
400
300
LFXT1Sx = 2
200
100
LFXT1Sx = 1
10
0.1
1
10
Crystal Frequency – MHz
Figure 14.
Copyright © 2004–2011, Texas Instruments Incorporated
100
0
0
4
8
12
16
20
Crystal Frequency – MHz
Figure 15.
29
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
Timer_A
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
fTA
Timer_A clock frequency
Internal: SMCLK, ACLK
External: TACLK, INCLK
Duty cycle = 50% ± 10%
tTA,cap
Timer_A capture timing
TA0, TA1, TA2
VCC
MIN
TYP
MAX
2.2 V
10
3V
16
2.2 V/3 V
20
UNIT
MHz
ns
Comparator_A+ (1)
over recommended operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
I(DD)
CAON = 1, CARSEL = 0, CAREF = 0
I(Refladder/RefDiode)
CAON = 1, CARSEL = 0, CAREF = 1/2/3,
No load at P2.3/CA0/TA1 and P2.4/CA1/TA2
TYP
MAX
2.2 V
VCC
MIN
25
40
3V
45
60
2.2 V
30
50
3V
45
71
UNIT
µA
µA
V(IC)
Common-mode input
voltage range
CAON = 1
2.2 V/3 V
0
V(Ref025)
(Voltage at 0.25 VCC
node) / VCC
PCA0 = 1, CARSEL = 1, CAREF = 1,
No load at P2.3/CA0/TA1 and P2.4/CA1/TA2
2.2 V/3 V
0.23
0.24
0.25
V(Ref050)
(Voltage at 0.5 VCC
node) / VCC
PCA0 = 1, CARSEL = 1, CAREF = 2,
No load at P2.3/CA0/TA1 and P2.4/CA1/TA2
2.2 V/3 V
0.47
0.48
0.5
See Figure 19 and
Figure 20
PCA0 = 1, CARSEL = 1, CAREF = 3,
No load at P2.3/CA0/TA1 and P2.4/CA1/TA2,
TA = 85°C
2.2 V
390
480
540
V(RefVT)
3V
400
490
550
V(offset)
Offset voltage (2)
2.2 V/3 V
-30
30
mV
Vhys
Input hysteresis
2.2 V/3 V
0
0.7
1.4
mV
TA = 25°C, Overdrive 10 mV,
Without filter: CAF = 0 (3)
(see Figure 16 and Figure 17)
2.2 V
80
165
300
3V
70
120
240
TA = 25°C, Overdrive 10 mV,
With filter: CAF = 1 (3)
(see Figure 16 and Figure 17)
2.2 V
1.4
1.9
2.8
3V
0.9
1.5
2.2
t(response)
(1)
(2)
(3)
30
Response time
(low-high and high-low)
CAON = 1
VCC - 1
V
mV
ns
µs
The leakage current for the Comparator_A+ terminals is identical to Ilkg(Px.y) specification.
The input offset voltage can be cancelled by using the CAEX bit to invert the Comparator_A+ inputs on successive measurements. The
two successive measurements are then summed together.
Response time measured at P2.2/CAOUT.
Copyright © 2004–2011, Texas Instruments Incorporated
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
0V
VCC
0
1
CAF
CAON
To Internal
Modules
Low-Pass Filter
+
_
V+
V−
0
0
1
1
CAOUT
Set CAIFG
Flag
τ ≈ 2.0 µs
Figure 16. Comparator_A+ Module Block Diagram
VCAOUT
Overdrive
V−
400 mV
t (response)
V+
Figure 17. Overdrive Definition
CASHORT
CA0
CA1
1
VIN
+
−
Comparator_A+
CASHORT = 1
IOUT = 10µA
Figure 18. Comparator_A+ Short Resistance Test Condition
Copyright © 2004–2011, Texas Instruments Incorporated
31
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
Typical Characteristics - Comparator_A+
V(RefVT)
vs
TEMPERATURE
VCC = 2.2 V
V(RefVT)
vs
TEMPERATURE
VCC = 2.2 V
650
650
VCC = 2.2 V
600
V(REFVT) – Reference Volts – mV
V(REFVT) – Reference Volts – mV
VCC = 3 V
Typical
550
500
450
400
-45
-25
15
55
75
35
-5
TA – Free-Air Temperature – °C
600
Typical
550
500
450
400
-45
95
-25
15
55
75
35
-5
TA – Free-Air Temperature – °C
Figure 19.
Figure 20.
SHORT RESISTANCE
vs
VIN/VCC
100
Short Resistance – kW
95
VCC = 1.8 V
VCC = 2.2 V
VCC = 3 V
10
VCC = 3.6 V
1
0
0.2
0.4
0.6
0.8
1.0
VIN/VCC – Normalized Input Voltage – V/V
Figure 21.
32
Copyright © 2004–2011, Texas Instruments Incorporated
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
Flash Memory
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VCC
MIN
TYP
MAX
UNIT
VCC (PGM/ERASE)
Program and erase supply voltage
2.2
3.6
V
fFTG
Flash timing generator frequency
257
476
kHz
IPGM
Supply current from VCC during program
2.2 V/3.6 V
3
5
mA
IERASE
Supply current from VCC during erase
2.2 V/3.6 V
3
7
mA
10
ms
(1)
tCPT
Cumulative program time
tCMErase
Cumulative mass erase time
2.2 V/3.6 V
2.2 V/3.6 V
20
ms
104
Program/erase endurance
105
cycles
tRetention
Data retention duration
TJ = 25°C
tWord
Word or byte program time
See
(2)
30
tFTG
tBlock,
0
Block program time for first byte or word
See
(2)
25
tFTG
tBlock,
1-63
Block program time for each additional
byte or word
See
(2)
18
tFTG
Block program end-sequence wait time
See
(2)
6
tFTG
Mass erase time
See
(2)
10593
tFTG
See
(2)
4819
tFTG
tBlock,
End
tMass Erase
tSeg Erase
(1)
(2)
Segment erase time
100
years
The cumulative program time must not be exceeded when writing to a 64-byte flash block. This parameter applies to all programming
methods: individual word/byte write and block write modes.
These values are hardwired into the flash controller's state machine (tFTG = 1/fFTG).
RAM
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
V(RAMh)
(1)
RAM retention supply voltage
(1)
TEST CONDITIONS
MIN
CPU halted
MAX
UNIT
1.6
V
This parameter defines the minimum supply voltage VCC when the data in RAM remains unchanged. No program execution should
happen during this supply voltage condition.
JTAG Interface
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
fTCK
TCK input frequency (1)
RInternal
Internal pulldown resistance on TEST
(1)
VCC
MIN
TYP
MAX
UNIT
2.2 V
0
5
MHz
3V
0
10
MHz
2.2 V/3 V
25
60
90
kΩ
MAX
fTCK may be restricted to meet the timing requirements of the module selected.
JTAG Fuse (1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
TA
MIN
VCC(FB)
Supply voltage during fuse-blow condition
PARAMETER
25°C
2.5
VFB
Voltage level on TEST for fuse blow
25°C
6
IFB
Supply current into TEST during fuse blow
25°C
100
mA
tFB
Time to blow fuse
25°C
1
ms
(1)
UNIT
V
7
V
Once the fuse is blown, no further access to the JTAG/Test and emulation features is possible, and the JTAG block is switched to
bypass mode.
Copyright © 2004–2011, Texas Instruments Incorporated
33
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
APPLICATION INFORMATION
Port P1 Pin Schematic: P1.0 to P1.3, Input/Output With Schmitt Trigger
Pad Logic
P1REN.x
P1DIR.x
0
P1OUT.x
0
1
0
1
1
Direction
0: Input
1: Output
1
Module XOUT
DVSS
DVCC
P1.0/TACLK
P1.1/TA0
P1.2/TA1
P1.3/TA2
P1SEL.x
P1IN.x
EN
Module XIN
D
P1IE.x
P1IRQ.x
EN
Q
P1IFG.x
P1SEL.x
P1IES.x
Set
Interrupt
Edge
Select
Table 17. Port P1 (P1.0 to P1.3) Pin Functions
PIN NAME (P1.x)
x
FUNCTION
P1.0
P1.0/TACLK
0
(1)
(I/O)
1
2
0
0
1
DVSS
1
1
I: 0; O: 1
0
Timer_A3.CCI0A
0
1
Timer_A3.TA0
1
1
I: 0; O: 1
0
Timer_A3.CCI0A
0
1
Timer_A3.TA0
1
1
I: 0; O: 1
0
Timer_A3.CCI0A
0
1
Timer_A3.TA0
1
1
P1.3 (1) (I/O)
P1.3/TA2
(1)
34
3
P1SEL.x
I: 0; O: 1
P1.2 (1) (I/O)
P1.2/TA1
P1DIR.x
TACLK
P1.1 (1) (I/O)
P1.1/TA0
CONTROL BITS / SIGNALS
Default after reset (PUC/POR)
Copyright © 2004–2011, Texas Instruments Incorporated
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
Port P1 Pin Schematic: P1.4 to P1.7, Input/Output With Schmitt Trigger
Pad Logic
P1REN.1
P1DIR.1
0
P1OUT.1
0
1
0
1
1
Direction
0: Input
1: Output
1
Module XOUT
DVSS
DVCC
P1.4/SMCLK/TCK
P1.5/TA0/TMS
P1.6/TA1/TDI
P1.7/TA2/TDO/TDI
Bus
Keeper
P1SEL.1
EN
P1IN.1
EN
Module XIN
D
P1IE.1
P1IRQ.1
EN
Q
P1IFG.1
P1SEL.1
P1IES.1
Set
Interrupt
Edge
Select
To JTAG
From JTAG
TDO From JTAG
P1.7/TA2/TDO/TDI only
TEST pad
TEST
JTAG
Fuse
DVSS
Copyright © 2004–2011, Texas Instruments Incorporated
35
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
Table 18. Port P1 (P1.4 to P1.7) Pin Functions
PIN NAME (P1.x)
x
FUNCTION
P1.4
P1.4/SMCLK/TCK
4
(2)
(I/O)
5
P1.7/TA2/TDO/TDI
(1)
(2)
(3)
36
6
7
P1SEL.x
TEST
I: 0; O: 1
0
0
1
1
0
TCK
X
X
1
I: 0; O: 1
0
0
Timer_A3.TA0
1
1
0
TMS
X
X
1
I: 0; O: 1
0
0
P1.6 (2) (I/O)
P1.6/TA1/TDI/TCLK
P1DIR.x
SMCLK
P1.5 (2) (I/O)
P1.5/TA0/TMS
CONTROL BITS / SIGNALS (1)
Timer_A3.TA1
1
1
0
TDI/TCLK (3)
X
X
1
P1.7 (2) (I/O)
I: 0; O: 1
0
0
Timer_A3.TA2
1
1
0
TDO/TDI (3)
X
X
1
X = don't care
Default after reset (PUC/POR)
Function controlled by JTAG
Copyright © 2004–2011, Texas Instruments Incorporated
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
Port P2 Pin Schematic: P2.0 to P2.5, Input/Output With Schmitt Trigger
Pad Logic
To Comparator_A+
From Comparator_A+
CAPD.x
P2REN.x
P2DIR.x
0
0
Module XOUT
1
0
DVCC
1
1
Direction
0: Input
1: Output
1
P2OUT.x
DVSS
P2.0/ACLK/CA2
P2.1/INCLK/CA3
P2.2/CAOUT/TA0/CA4
P2.3/TA1/CA0
P2.4/TA2/CA1
P2.5/CA5
Bus
Keeper
P2SEL.x
EN
P2IN.x
EN
Module XIN
D
P2IE.x
P2IRQ.x
EN
Q
Set
P2IFG.x
P2SEL.x
P2IES.x
Interrupt
Edge
Select
Table 19. Control Signal " From Comparator_A+"
PIN NAME
FUNCTION
SIGNAL "From Comparator_A+" = 1 (1)
P2CA4
P2CA0
P2CA3
P2CA2
P2CA1
P2.0/ACLK/CA2
CA2
1
1
0
1
0
P2.1/INCLK/CA3
CA3
N/A
N/A
0
1
1
P2.2/CAOUT/TA0/CA4
CA4
N/A
N/A
1
0
0
P2.3/TA1/CA0
CA0
0
1
N/A
N/A
N/A
P2.4/TA2/CA1
CA1
1
0
0
0
1
P2.5/CA5
CA5
N/A
N/A
1
0
1
(1)
OR
N/A = Not available or not applicable
Copyright © 2004–2011, Texas Instruments Incorporated
37
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
Table 20. Port P2 (P2.0 to P2.5) Pin Functions
PIN NAME (P2.x)
x
FUNCTION
P2.0
P2.0/ACLK/CA2
0
(2)
(I/O)
1
2
3
0
0
1
0
CA2 (3)
X
X
1
I: 0; O: 1
0
0
Timer_A3.INCLK
0
1
0
DVSS
1
1
0
CA3 (3)
X
X
1
P2.5/CA5
(1)
(2)
(3)
38
4
5
(2)
I: 0; O: 1
0
0
Timer_A3.CCI0B
0
1
0
CAOUT
1
1
0
(3)
X
X
1
P2.3 (2) (I/O)
I: 0; O: 1
0
0
Timer_A3.TA1
1
1
0
CA0 (3)
X
X
1
P2.4
P2.4/TA2/CA1
CAPD.x
1
CA4
P2.3/TA1/CA0
P2SEL.x
I: 0; O: 1
P2.2
P2.2/CAOUT/TA0/CA4
P2DIR.x
ACLK
P2.1 (2) (I/O)
P2.1/INCLK/CA3
CONTROL BITS / SIGNALS (1)
(2)
(I/O)
I: 0; O: 1
0
0
Timer_A3.TA2
1
1
0
CA1 (3)
X
X
1
I: 0; O: 1
0
0
X
X
1
P2.5
(2)
CA5 (3)
(I/O)
(I/O)
X = don't care
Default after reset (PUC/POR)
Setting theCAPD.x bit disables the output driver as well as the input Schmitt trigger to prevent parasitic cross currentswhen applying
analog signals. Selecting the CAx input pin to the comparator multiplexer with the P2CAx bits automatically disables the input buffer for
that pin, regardless of the state of the associated CAPD.x bit.
Copyright © 2004–2011, Texas Instruments Incorporated
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
Port P2 Pin Schematic: P2.6, Input/Output With Schmitt Trigger and Crystal Oscillator Input
Pad Logic
To Comparator_A+
From Comparator_A+
CAPD.x
LFXT1 Oscillator
BCSCTL3.LFXT1Sx = 11
P2.7/XOUT/CA7
LFXT1 off
0
LFXT1CLK
1
P2SEL.7
P2REN.6
P2DIR.6
0
0
Module XOUT
1
0
DVCC
1
1
Direction
0: Input
1: Output
1
P2OUT.6
DVSS
P2.6/XIN/CA6
Bus
Keeper
P2SEL.6
EN
P2IN.6
EN
Module XIN
D
P2IE.6
P2IRQ.6
EN
Q
P2IFG.6
P2SEL.6
P2IES.6
Set
Interrupt
Edge
Select
Table 21. Control Signal " From Comparator_A+"
PIN NAME
P2.6/XIN/CA6
FUNCTION
CA6
Copyright © 2004–2011, Texas Instruments Incorporated
SIGNAL "From Comparator_A+" = 1
P2CA3
P2CA2
P2CA1
1
1
0
39
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
Table 22. Port P2 (P2.6) Pin Functions
PIN NAME (P2.x)
x
FUNCTION
P2.6 (I/O)
P2.6/XIN/CA6
(1)
(2)
(3)
40
6
CONTROL BITS / SIGNALS (1)
P2DIR.x
P2SEL.x
CAPD.x
I: 0; O: 1
0
0
XIN (2)
X
1
0
CA6 (3)
X
X
1
X = don't care
Default after reset (PUC/POR)
Setting theCAPD.x bit disables the output driver as well as the input Schmitt trigger to prevent parasitic cross currentswhen applying
analog signals. Selecting the CAx input pin to the comparator multiplexer with the P2CAx bits automatically disables the input buffer for
that pin, regardless of the state of the associated CAPD.x bit.
Copyright © 2004–2011, Texas Instruments Incorporated
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
Port P2 Pin Schematic: P2.7, Input/Output With Schmitt Trigger and Crystal Oscillator Output
Pad Logic
To Comparator_A+
From Comparator_A+
CAPD.x
LFXT1 Oscillator
BCSCTL3.LFXT1Sx = 11
LFXT1 off
0
LFXT1CLK
1
From
P2.6/XIN
P2.6/XIN/CA6
Pad Logic
P2SEL.6
P2REN.7
P2DIR.7
0
0
Module XOUT
1
0
DVCC
1
1
Direction
0: Input
1: Output
1
P2OUT.7
DVSS
P2.7/XOUT/CA7
Bus
Keeper
P2SEL.7
EN
P2IN.7
EN
Module XIN
D
P2IE.7
P2IRQ.7
EN
Q
P2IFG.7
P2SEL.7
P2IES.7
Set
Interrupt
Edge
Select
Table 23. Control Signal " From Comparator_A+"
PIN NAME
FUNCTION
P2.7/XOUT/CA7
CA7
Copyright © 2004–2011, Texas Instruments Incorporated
SIGNAL "From Comparator_A+" = 1
P2CA3
P2CA2
P2CA1
1
1
1
41
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
Table 24. Port P2 (P2.7) Pin Functions
PIN NAME (P2.x)
P2.7/XOUT/CA7
(1)
(2)
(3)
(4)
42
x
6
FUNCTION
CONTROL BITS / SIGNALS (1)
P2DIR.x
P2SEL.x
CAPD.x
P2.7 (I/O)
I: 0; O: 1
0
0
XOUT (2) (3)
X
1
0
CA7 (4)
X
X
1
X = don't care
Default after reset (PUC/POR)
If the pin XOUT/P2.7/CA7 is used as an input a current can flow until P2SEL.7 is cleared due to the oscillator output driver connection to
this pin after reset.
Setting theCAPD.x bit disables the output driver as well as the input Schmitt trigger to prevent parasitic cross currentswhen applying
analog signals. Selecting the CAx input pin to the comparator multiplexer with the P2CAx bits automatically disables the input buffer for
that pin, regardless of the state of the associated CAPD.x bit.
Copyright © 2004–2011, Texas Instruments Incorporated
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
JTAG Fuse Check Mode
MSP430 devices that have the fuse on the TEST terminal have a fuse check mode that tests the continuity of the
fuse the first time the JTAG port is accessed after a power-on reset (POR). When activated, a fuse check
current, ITF , of 1 mA at 3 V, 2.5 mA at 5 V can flow from the TEST pin to ground if the fuse is not burned. Care
must be taken to avoid accidentally activating the fuse check mode and increasing overall system power
consumption.
When the TEST pin is again taken low after a test or programming session, the fuse check mode and sense
currents are terminated.
Activation of the fuse check mode occurs with the first negative edge on the TMS pin after power up or if TMS is
being held low during power up. The second positive edge on the TMS pin deactivates the fuse check mode.
After deactivation, the fuse check mode remains inactive until another POR occurs. After each POR the fuse
check mode has the potential to be activated.
The fuse check current flows only when the fuse check mode is active and the TMS pin is in a low state (see
Figure 22). Therefore, the additional current flow can be prevented by holding the TMS pin high (default
condition).
Time TMS Goes Low After POR
TMS
ITF
ITEST
Figure 22. Fuse Check Mode Current
NOTE
The CODE and RAM data protection is ensured if the JTAG fuse is blown and the 256-bit
bootloader access key is used. Also, see the Bootstrap Loader section for more
information.
Copyright © 2004–2011, Texas Instruments Incorporated
43
MSP430F21x1
SLAS439F – SEPTEMBER 2004 – REVISED AUGUST 2011
www.ti.com
REVISION HISTORY
Literature
Number
Summary
SLAS439
PRODUCT PREVIEW release
SLAS439A
PRODUCTION DATA release
SLAS439B
Corrected instruction cycle time to 62.5ns, pg 1.
Updated Figure 1, pg 12.
Updated Figures 2 and 3, pg 13.
RPull unit corrected from Ω to kΩ, pg 15.
MAX load current specification and Note 3 removed from "outputs" table, pg 16.
MIN and MAX percentages for "calibrated DCO frequencies - tolerance over supply voltage VCC" corrected from 2.5% to
3% to match the specified frequency ranges., pg 22.
SLAS439C
MSP430x21x1T production data sheet release.
105°C characterization results added.
SLAS439D
Corrected Timer_A2 to Timer_A3 and added TACCR2 to Interrupt Flag column in "interrupt vector addresses", pg 6
SLAS439E
Changed Tstg, Programmed device, to -40°C to 150°C in Absolute Maximum Ratings.
Corrected Test Conditions for OAHF row and and Duty Cycle row in Crystal Oscillator LFXT1, High-Frequency Mode.
SLAS439F
Changed Tstg, Programmed device, to -55°C to 150°C in Absolute Maximum Ratings.
44
Copyright © 2004–2011, Texas Instruments Incorporated
PACKAGE OPTION ADDENDUM
www.ti.com
29-Jul-2011
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
(3)
MSP430F2101IDGV
ACTIVE
TVSOP
DGV
20
90
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430F2101IDGVR
ACTIVE
TVSOP
DGV
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430F2101IDW
ACTIVE
SOIC
DW
20
25
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430F2101IDWR
ACTIVE
SOIC
DW
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430F2101IPW
ACTIVE
TSSOP
PW
20
70
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430F2101IPWR
ACTIVE
TSSOP
PW
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430F2101IRGER
ACTIVE
VQFN
RGE
24
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430F2101IRGET
ACTIVE
VQFN
RGE
24
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430F2101TDGV
ACTIVE
TVSOP
DGV
20
90
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430F2101TDGVR
ACTIVE
TVSOP
DGV
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430F2101TDW
ACTIVE
SOIC
DW
20
25
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430F2101TDWR
ACTIVE
SOIC
DW
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430F2101TPW
ACTIVE
TSSOP
PW
20
70
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430F2101TPWR
ACTIVE
TSSOP
PW
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430F2101TRGER
ACTIVE
VQFN
RGE
24
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430F2101TRGET
ACTIVE
VQFN
RGE
24
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430F2111IDGV
ACTIVE
TVSOP
DGV
20
90
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Addendum-Page 1
Samples
(Requires Login)
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
29-Jul-2011
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
(3)
MSP430F2111IDGVR
ACTIVE
TVSOP
DGV
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430F2111IDW
ACTIVE
SOIC
DW
20
25
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430F2111IDWR
ACTIVE
SOIC
DW
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430F2111IPW
ACTIVE
TSSOP
PW
20
70
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430F2111IPWR
ACTIVE
TSSOP
PW
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430F2111IRGER
ACTIVE
VQFN
RGE
24
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430F2111IRGET
ACTIVE
VQFN
RGE
24
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430F2111TDGV
ACTIVE
TVSOP
DGV
20
90
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430F2111TDGVR
ACTIVE
TVSOP
DGV
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430F2111TDW
ACTIVE
SOIC
DW
20
25
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430F2111TDWR
ACTIVE
SOIC
DW
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430F2111TPW
ACTIVE
TSSOP
PW
20
70
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430F2111TPWR
ACTIVE
TSSOP
PW
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430F2111TRGER
ACTIVE
VQFN
RGE
24
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430F2111TRGET
ACTIVE
VQFN
RGE
24
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430F2121IDGV
ACTIVE
TVSOP
DGV
20
90
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430F2121IDGVR
ACTIVE
TVSOP
DGV
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430F2121IDW
ACTIVE
SOIC
DW
20
25
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Addendum-Page 2
Samples
(Requires Login)
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
29-Jul-2011
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
(3)
MSP430F2121IDWR
ACTIVE
SOIC
DW
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430F2121IPW
ACTIVE
TSSOP
PW
20
70
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430F2121IPWR
ACTIVE
TSSOP
PW
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430F2121IRGER
ACTIVE
VQFN
RGE
24
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430F2121IRGET
ACTIVE
VQFN
RGE
24
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430F2121TDGV
ACTIVE
TVSOP
DGV
20
90
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430F2121TDGVR
ACTIVE
TVSOP
DGV
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430F2121TDW
ACTIVE
SOIC
DW
20
25
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430F2121TDWR
ACTIVE
SOIC
DW
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430F2121TPW
ACTIVE
TSSOP
PW
20
70
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430F2121TPWR
ACTIVE
TSSOP
PW
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430F2121TRGER
ACTIVE
VQFN
RGE
24
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430F2121TRGET
ACTIVE
VQFN
RGE
24
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430F2131IDGV
ACTIVE
TVSOP
DGV
20
90
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430F2131IDGVR
ACTIVE
TVSOP
DGV
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430F2131IDW
ACTIVE
SOIC
DW
20
25
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430F2131IDWR
ACTIVE
SOIC
DW
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430F2131IPW
ACTIVE
TSSOP
PW
20
70
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Addendum-Page 3
Samples
(Requires Login)
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
29-Jul-2011
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
(3)
MSP430F2131IPWR
ACTIVE
TSSOP
PW
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430F2131IRGER
ACTIVE
VQFN
RGE
24
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430F2131IRGET
ACTIVE
VQFN
RGE
24
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430F2131TDGV
ACTIVE
TVSOP
DGV
20
90
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430F2131TDGVR
ACTIVE
TVSOP
DGV
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430F2131TDW
ACTIVE
SOIC
DW
20
25
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430F2131TDWR
ACTIVE
SOIC
DW
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430F2131TPW
ACTIVE
TSSOP
PW
20
70
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430F2131TPWR
ACTIVE
TSSOP
PW
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430F2131TRGER
ACTIVE
VQFN
RGE
24
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430F2131TRGET
ACTIVE
VQFN
RGE
24
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Samples
(Requires Login)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Addendum-Page 4
PACKAGE OPTION ADDENDUM
www.ti.com
29-Jul-2011
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 5
PACKAGE MATERIALS INFORMATION
www.ti.com
19-Aug-2011
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
MSP430F2101IDGVR
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
TVSOP
DGV
20
2000
330.0
12.4
6.9
5.6
1.6
8.0
12.0
Q1
MSP430F2101IDWR
SOIC
DW
20
2000
330.0
24.4
10.8
13.0
2.7
12.0
24.0
Q1
MSP430F2101IPWR
TSSOP
PW
20
2000
330.0
16.4
6.95
7.1
1.6
8.0
16.0
Q1
MSP430F2101IRGER
VQFN
RGE
24
3000
330.0
12.4
4.25
4.25
1.15
8.0
12.0
Q2
MSP430F2101IRGET
VQFN
RGE
24
250
180.0
12.4
4.25
4.25
1.15
8.0
12.0
Q2
MSP430F2101TDGVR
TVSOP
DGV
20
2000
330.0
12.4
6.9
5.6
1.6
8.0
12.0
Q1
MSP430F2101TDWR
SOIC
DW
20
2000
330.0
24.4
10.8
13.0
2.7
12.0
24.0
Q1
MSP430F2101TPWR
TSSOP
PW
20
2000
330.0
16.4
6.95
7.1
1.6
8.0
16.0
Q1
MSP430F2101TRGER
VQFN
RGE
24
3000
330.0
12.4
4.25
4.25
1.15
8.0
12.0
Q2
MSP430F2101TRGET
VQFN
RGE
24
250
180.0
12.4
4.25
4.25
1.15
8.0
12.0
Q2
MSP430F2111IDGVR
TVSOP
DGV
20
2000
330.0
12.4
6.9
5.6
1.6
8.0
12.0
Q1
MSP430F2111IDWR
SOIC
DW
20
2000
330.0
24.4
10.8
13.0
2.7
12.0
24.0
Q1
MSP430F2111IPWR
TSSOP
PW
20
2000
330.0
16.4
6.95
7.1
1.6
8.0
16.0
Q1
MSP430F2111IRGER
VQFN
RGE
24
3000
330.0
12.4
4.25
4.25
1.15
8.0
12.0
Q2
MSP430F2111IRGET
VQFN
RGE
24
250
180.0
12.4
4.25
4.25
1.15
8.0
12.0
Q2
MSP430F2111TDGVR
TVSOP
DGV
20
2000
330.0
12.4
6.9
5.6
1.6
8.0
12.0
Q1
MSP430F2111TDWR
SOIC
DW
20
2000
330.0
24.4
10.8
13.0
2.7
12.0
24.0
Q1
MSP430F2111TPWR
TSSOP
PW
20
2000
330.0
16.4
6.95
7.1
1.6
8.0
16.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
19-Aug-2011
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
MSP430F2111TRGER
VQFN
RGE
24
3000
330.0
12.4
4.25
4.25
1.15
8.0
12.0
Q2
MSP430F2111TRGET
VQFN
RGE
24
250
180.0
12.4
4.25
4.25
1.15
8.0
12.0
Q2
MSP430F2121IDGVR
TVSOP
DGV
20
2000
330.0
12.4
6.9
5.6
1.6
8.0
12.0
Q1
MSP430F2121IDWR
SOIC
DW
20
2000
330.0
24.4
10.8
13.0
2.7
12.0
24.0
Q1
MSP430F2121IPWR
TSSOP
PW
20
2000
330.0
16.4
6.95
7.1
1.6
8.0
16.0
Q1
MSP430F2121IRGER
VQFN
RGE
24
3000
330.0
12.4
4.25
4.25
1.15
8.0
12.0
Q2
MSP430F2121IRGET
VQFN
RGE
24
250
180.0
12.4
4.25
4.25
1.15
8.0
12.0
Q2
MSP430F2121TDGVR
TVSOP
DGV
20
2000
330.0
12.4
6.9
5.6
1.6
8.0
12.0
Q1
MSP430F2121TDWR
SOIC
DW
20
2000
330.0
24.4
10.8
13.0
2.7
12.0
24.0
Q1
MSP430F2121TPWR
TSSOP
PW
20
2000
330.0
16.4
6.95
7.1
1.6
8.0
16.0
Q1
MSP430F2121TRGER
VQFN
RGE
24
3000
330.0
12.4
4.25
4.25
1.15
8.0
12.0
Q2
MSP430F2121TRGET
VQFN
RGE
24
250
180.0
12.4
4.25
4.25
1.15
8.0
12.0
Q2
MSP430F2131IDGVR
TVSOP
DGV
20
2000
330.0
12.4
6.9
5.6
1.6
8.0
12.0
Q1
MSP430F2131IDWR
SOIC
DW
20
2000
330.0
24.4
10.8
13.0
2.7
12.0
24.0
Q1
MSP430F2131IPWR
TSSOP
PW
20
2000
330.0
16.4
6.95
7.1
1.6
8.0
16.0
Q1
MSP430F2131IRGER
VQFN
RGE
24
3000
330.0
12.4
4.25
4.25
1.15
8.0
12.0
Q2
MSP430F2131IRGET
VQFN
RGE
24
250
180.0
12.4
4.25
4.25
1.15
8.0
12.0
Q2
MSP430F2131TDGVR
TVSOP
DGV
20
2000
330.0
12.4
6.9
5.6
1.6
8.0
12.0
Q1
MSP430F2131TDWR
SOIC
DW
20
2000
330.0
24.4
10.8
13.0
2.7
12.0
24.0
Q1
MSP430F2131TPWR
TSSOP
PW
20
2000
330.0
16.4
6.95
7.1
1.6
8.0
16.0
Q1
MSP430F2131TRGER
VQFN
RGE
24
3000
330.0
12.4
4.25
4.25
1.15
8.0
12.0
Q2
MSP430F2131TRGET
VQFN
RGE
24
250
180.0
12.4
4.25
4.25
1.15
8.0
12.0
Q2
Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
19-Aug-2011
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
MSP430F2101IDGVR
TVSOP
DGV
20
2000
346.0
346.0
29.0
MSP430F2101IDWR
SOIC
DW
20
2000
346.0
346.0
41.0
MSP430F2101IPWR
TSSOP
PW
20
2000
346.0
346.0
33.0
MSP430F2101IRGER
VQFN
RGE
24
3000
346.0
346.0
29.0
MSP430F2101IRGET
VQFN
RGE
24
250
210.0
185.0
35.0
MSP430F2101TDGVR
TVSOP
DGV
20
2000
346.0
346.0
29.0
MSP430F2101TDWR
SOIC
DW
20
2000
346.0
346.0
41.0
MSP430F2101TPWR
TSSOP
PW
20
2000
346.0
346.0
33.0
MSP430F2101TRGER
VQFN
RGE
24
3000
346.0
346.0
29.0
MSP430F2101TRGET
VQFN
RGE
24
250
210.0
185.0
35.0
MSP430F2111IDGVR
TVSOP
DGV
20
2000
346.0
346.0
29.0
MSP430F2111IDWR
SOIC
DW
20
2000
346.0
346.0
41.0
MSP430F2111IPWR
TSSOP
PW
20
2000
346.0
346.0
33.0
MSP430F2111IRGER
VQFN
RGE
24
3000
346.0
346.0
29.0
MSP430F2111IRGET
VQFN
RGE
24
250
210.0
185.0
35.0
MSP430F2111TDGVR
TVSOP
DGV
20
2000
346.0
346.0
29.0
MSP430F2111TDWR
SOIC
DW
20
2000
346.0
346.0
41.0
MSP430F2111TPWR
TSSOP
PW
20
2000
346.0
346.0
33.0
MSP430F2111TRGER
VQFN
RGE
24
3000
346.0
346.0
29.0
MSP430F2111TRGET
VQFN
RGE
24
250
210.0
185.0
35.0
Pack Materials-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
19-Aug-2011
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
MSP430F2121IDGVR
TVSOP
DGV
20
2000
346.0
346.0
29.0
MSP430F2121IDWR
SOIC
DW
20
2000
346.0
346.0
41.0
MSP430F2121IPWR
TSSOP
PW
20
2000
346.0
346.0
33.0
MSP430F2121IRGER
VQFN
RGE
24
3000
346.0
346.0
29.0
MSP430F2121IRGET
VQFN
RGE
24
250
210.0
185.0
35.0
MSP430F2121TDGVR
TVSOP
DGV
20
2000
346.0
346.0
29.0
MSP430F2121TDWR
SOIC
DW
20
2000
346.0
346.0
41.0
MSP430F2121TPWR
TSSOP
PW
20
2000
346.0
346.0
33.0
MSP430F2121TRGER
VQFN
RGE
24
3000
346.0
346.0
29.0
MSP430F2121TRGET
VQFN
RGE
24
250
210.0
185.0
35.0
MSP430F2131IDGVR
TVSOP
DGV
20
2000
346.0
346.0
29.0
MSP430F2131IDWR
SOIC
DW
20
2000
346.0
346.0
41.0
MSP430F2131IPWR
TSSOP
PW
20
2000
346.0
346.0
33.0
MSP430F2131IRGER
VQFN
RGE
24
3000
346.0
346.0
29.0
MSP430F2131IRGET
VQFN
RGE
24
250
210.0
185.0
35.0
MSP430F2131TDGVR
TVSOP
DGV
20
2000
346.0
346.0
29.0
MSP430F2131TDWR
SOIC
DW
20
2000
346.0
346.0
41.0
MSP430F2131TPWR
TSSOP
PW
20
2000
346.0
346.0
33.0
MSP430F2131TRGER
VQFN
RGE
24
3000
346.0
346.0
29.0
MSP430F2131TRGET
VQFN
RGE
24
250
210.0
185.0
35.0
Pack Materials-Page 4
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Communications and Telecom www.ti.com/communications
Amplifiers
amplifier.ti.com
Computers and Peripherals
www.ti.com/computers
Data Converters
dataconverter.ti.com
Consumer Electronics
www.ti.com/consumer-apps
DLP® Products
www.dlp.com
Energy and Lighting
www.ti.com/energy
DSP
dsp.ti.com
Industrial
www.ti.com/industrial
Clocks and Timers
www.ti.com/clocks
Medical
www.ti.com/medical
Interface
interface.ti.com
Security
www.ti.com/security
Logic
logic.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Power Mgmt
power.ti.com
Transportation and
Automotive
www.ti.com/automotive
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
Wireless
www.ti.com/wireless-apps
RF/IF and ZigBee® Solutions
www.ti.com/lprf
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated