ISL6293 ® Data Sheet January 4, 2006 FN9180.1 Li-ion/Li Polymer Battery Charger Accepting Two Power Sources Features The ISL6293 is a fully integrated low-cost single-cell Li-ion or Li-polymer battery charger. The charger accepts two power inputs, normally one from a USB (Universal Serial Bus) port and another one from a desktop cradle. The ISL6293 is an ideal charger for smart handheld devices that need to communicate with a personal computer via USB. • Accept Two Power Sources The ISL6293 features 28V and 7V maximum voltages for the cradle and the USB inputs respectively. The 28V rating allows low-cost adapters be safely used. When both inputs are powered, the cradle input is used to charge the battery. The charge current is independently programmable for both inputs with two small resistors. One additional USBP pin allows the selection of high-power or low-power port for the USB input. The charger is self-protected against over temperature. If the die temperature rises above 100°C, a thermal foldback function reduces the charge current automatically to prevent further temperature rise. The charger preconditions the battery with low current when the battery voltage is below 2.6V. The charger has two indication pins. The PPR (power present) pin outputs an open-drain logic LOW when either the cradle or the USB input power is attached. The CHG (charge) pin is also an open-drain output that indicates a logic LOW when the charge current is above a minimum current level. When the charge current is below the minimum current, the charger remains in operation but the CHG pin indicates a logic HIGH signal. • Charge Current Thermal Foldback for Thermal Protection Ordering Information Related Literature PART NUMBER TEMP. RANGE PART (°C) MARKING PACKAGE • Complete Charger for Single-Cell Li-ion/Polymer Batteries PKG. DWG. # ISL6293-2CR 93-2 -40 to 85 10 Ld 3x3 DFN L10.3x3 ISL6293-2CR-T 93-2 10 Ld 3x3 DFN Tape and Reel ISL6293-2CRZ (Note) 932Z -40 to 85 10 Ld 3x3 DFN L10.3x3 (Pb-free) ISL6293-2CRZ-T 932Z (Note) • Low Component Count - Integrated Pass Element - Integrated Charge-Current Sensor with 10% Accuracy - No External Blocking Diode Required • 28V Maximum Voltage for the Cradle Input • Charge Indication • Adapter Presence Indication • Less than 1µA Leakage Current off the Battery when No Input Power Attached • Ambient Temperature Range: -40°C to 85°C • Thermally-Enhanced 3x3 DFN Package • Pb-Free Plus Anneal Available (RoHS Compliant) Applications • Smart Handheld Devices • Cell Phones, PDAs, MP3 Players • Digital Still Cameras • Handheld Test Equipment • Technical Brief TB363 “Guidelines for Handling and Processing Moisture Sensitive Surface Mount Devices (SMDs)” • Technical Brief TB389 “PCB Land Pattern Design and Surface Mount Guidelines for QFN Packages” Pinout ISL6293-2 (10 LD 3X3 DFN) TOP VIEW 10 Ld 3x3 DFN Tape and Reel (Pb-free) NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 1 CRDL 1 10 BAT USB 2 9 ICDL PPR 3 8 GND CHG 4 7 USBP EN 5 6 IUSB CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2004, 2006. All Rights Reserved All other trademarks mentioned are the property of their respective owners. ISL6293 Block Diagram CRDL BAT USB Temp Monitor ICDL IUSB USBP CA + CPPR + VA Reference Current Control CPPR LBAT VREF IR USB CRDL BAT ENA EN PPR Control GND CHG 2 FN9180.1 January 4, 2006 ISL6293 Typical Applications A Simple Charger Accepting Power from Both a USB Port and a Desktop Cradle To Cradle Connector To Battery BAT CRDL C1 To USB Connector ICDL ISL6293-2 USB R1 C2 IUSB RICDL RIUSB PPR R3 D1 D2 C3 CHG EN 500mA 100mA R2 Disable Enable GND USBP COMPONENT SELECTION RICDL 1.82kΩ for 0.8A cradle charge current RIUSB 80kΩ for 100mA/500mA USB charge current R2, R3 470Ω C1, C2, C3 R1 D1, D2 1µF ceramic capacitor 1Ω LEDs A Simple Charger with Programmable Charge Current and Wide Input Voltage Range BAT USB To Cradle Connector ICDL CRDL C1 RICDL C2 IUSB ISL6293-2 USBP Disable Enable To Battery PPR CHG EN GND COMPONENT SELECTION RICDL 1.82kΩ for 0.8A cradle charge current C1, C2 1µF ceramic capacitor RIUSB is not required when the USB input of ISL6293-2 is left floating in the design for a single input charger. 3 FN9180.1 January 4, 2006 ISL6293 Absolute Maximum Ratings Thermal Information Supply Voltage (USB) . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 7V Supply Voltage (CRDL) . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 28V Signal Input Voltage (EN, USBP, ICDL, IUSB, BAT) . . . . -0.3V to 7V Open-Drain Pull-Up Voltage (PPR, CHG) . . . . . . . . . . . . -0.3V to 7V Thermal Resistance Recommended Operating Conditions θJA (°C/W) θJC (°C/W) 3x3 DFN Package (Notes 1, 2) . . . . . . 46 4 Maximum Junction Temperature (Plastic Package) . . . . . . . . 150°C Maximum Storage Temperature Range . . . . . . . . . . . -65°C to 150°C Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300°C Ambient Temperature Range . . . . . . . . . . . . . . . . . . . .-40°C to 85°C Supply Voltage (USB Pin) . . . . . . . . . . . . . . . . . . . . . . 4.3V to 5.5V Supply Voltage (CRDL Pin) . . . . . . . . . . . . . . . . . . . . . . 4.3V to 24V Typical Cradle Charge Current . . . . . . . . . . . . . . . . . . 300mA to 1A Typical USB Charge Current . . . . . . . . . . . . . . . . 350mA to 450mA CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. θJA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech Brief TB379. 2. For θJC, the “case temp” location is the center of the exposed metal pad on the package underside. Electrical Specifications Typical Values Are Tested at USB = CRDL = 5V and ambient temperature is at 25°C, Unless Otherwise Noted. All Maximum and Minimum Values Are Guaranteed Under the Recommended Operating Conditions. PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNITS Rising USB/CRDL Threshold 3.4 3.7 4.0 V Falling USB/CRDL Threshold 3.2 3.5 3.8 V POWER-ON RESET VIN-BAT OFFSET VOLTAGE Rising Edge VOS Falling Edge VOS VBAT = 4.0V, use CHG pin to indicate the comparator output (Note 3) 175 mV 110 mV STANDBY CURRENT BAT Pin Sink Current ISTANDBY EN = HIGH or both inputs are floating CRDL Pin Supply Current ICRDL USB Pin Supply Current EN = HIGH µA 150 IUSB CRDL/USB Pin Supply Current µA 1.0 150 EN = LOW or floating µA 250 0.55 mA VOLTAGE REGULATION Output Voltage (Note 4) VCH Charge current = 20mA 4.158 4.2 4.242 V CRDL PMOS On Resistance VBAT = 3.8V, ICHARGER = 0.5A 700 mΩ USB PMOS On Resistance VBAT = 3.8V, ICHARGER = 0.35A 700 mΩ CHARGE CURRENT (Note 5) ICDL Pin Output Voltage VICDL IUSB Pin Output Voltage VIUSB VBAT = 3.8V 1.17 1.20 1.23 V 0.776 0.8 0.824 V CRDL Input Constant Charge Current ICHARGE RICDL = 1.82kΩ, VBAT = 3.8V Valid for -10°C to 85°C 720 800 880 mA CRDL Input Trickle Charge Current ITRICKLE 9.2 13.2 17.2 % USB Input Constant Charge Current ICHARGE USBP = HIGH, RIUSB = 80kΩ, VBAT = 3.8V 380 440 500 mA USB Input Trickle Charge Current (Note 4) ITRICKLE 8.0 10.0 12.0 % 4 RICDL = 1.82kΩ, VBAT = 2.4V Given as a percentage of the CRDL ICHARGE Valid for -10°C to 85°C USBP = HIGH, RIUSB = 80kΩ, VBAT = 2.4V Given as a percentage of the USB HIGH ICHARGE FN9180.1 January 4, 2006 ISL6293 Electrical Specifications Typical Values Are Tested at USB = CRDL = 5V and ambient temperature is at 25°C, Unless Otherwise Noted. All Maximum and Minimum Values Are Guaranteed Under the Recommended Operating Conditions. (Continued) PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNITS 68 84 100 mA USBP = LOW, RIUSB = 80kΩ, VBAT = 2.4V Given as a percentage of the USB LOW ICHARGE 45.0 50.0 55.0 % USB Input Constant Charge Current ICHARGE USBP = LOW, RIUSB = 80kΩ, VBAT = 3.8V USB Input Trickle Charge Current ITRICKLE END-OF-CHARGE CURRENT THRESHOLD Powered From USB Pin IEOC USBP = HIGH, RIUSB = 80kΩ Given as a percentage of the USB HIGH ICHARGE 8.0 10.5 13.0 % Powered From USB Pin IEOC USBP = LOW, RIUSB = 80kΩ Given as a percentage of the USB LOW ICHARGE 17.0 21.0 25.0 % Powered From CRDL Pin IEOC RICDL = 1.82kΩ, Given as a percentage of the CRDL ICHARGE 5.5 8.5 11.0 % VMIN 2.5 2.6 2.7 V TFOLD 85 100 115 °C PRECONDITIONING CHARGE THRESHOLD Preconditioning Charge Threshold Voltage INTERNAL TEMPERATURE MONITORING Current Foldback Threshold (Note 5) LOGIC INPUT AND OUTPUT USBP Pin Logic Input High 2.0 V USBP Pin Logic Input Low 0.4 USBP Pin Internal Pull Down Resistance V 1000 EN Pin Logic Input High kΩ 1.2 V EN Pin Logic Input Low 0.4 EN Pin Internal Pull Down Resistance CHG/PPR Sink Current V 1000 Pin Voltage = 0.8V kΩ 15 mA NOTES: 3. The 4.0V VBAT is selected so that the CHG output can be used as the indication for the offset comparator output indication. If the VBAT is lower than the POR threshold, no output pin can be used for indication. 4. The maximum and minimum limits are guaranteed over -40°C to 70°C ambient temperature range. 5. The charge current may be reduced by the thermal foldback function, depending on the heatsinking condition of the test setup. 6. The threshold value at which the charger output is reduced to near zero. Guaranteed by characterization or correlation to other test. Functional Pin Description CRDL (Pin 1) Cradle input. This pin is usually connected to a cradle power input. The maximum input voltage is 28V. The charge current from this pin is programmable with the ICDL pin up to 1A. When this pin is connected to a power source, no charge current is drawn from the USB pin. A 1µF or larger value ceramic capacitor is recommended for decoupling. USB (Pin 2) USB input. This pin is usually connected to a USB port power connector. Other sources that are lower than 5.5V are also acceptable. The charge current from the USB pin is selectable between 100mA and 500mA maximum with the 5 USBP pin when the RIUSB = 80kΩ. A 1µF or larger value ceramic capacitor is recommended for decoupling. It is also recommended to have a 1Ω resistor in series with the decoupling capacitor to prevent an over-shoot voltage when a USB hot plug event occurs. PPR (Pin 3) Power presence indication. This is an open-drain output pin that outputs a logic LOW when either the USB input voltage or the CRDL input voltage is above its POR level, regardless if the charger is enabled or disabled. This pin provides a wake-up signal to a microprocessor when either the cradle or the USB power is connected. FN9180.1 January 4, 2006 ISL6293 CHG (Pin 4) TABLE 1. RATIO vs. RICDL Charge indication pin. When the charge current from the cradle input during the constant current mode falls to below 8% of the programmed reference current by the ICDL pin or the charge current from the USB input is below 10% of the programmed charge current, the open-drain MOSFET is turned off. The pin will be pulled to logic HIGH by an external resistor to indicate the End Of Charge. RICDL (kΩ) 1.5 2.2 3.0 3.9 4.6 Ratio 1291 1216 1155 1122 1088 It is recommended that the charge current be programmed in the range of 300mA to 1A. EN (Pin 5) 1280 Enable logic input. Connect to LOW or leave floating to enable the charger. 1250 The IUSB pin programs the USB charge current. This pin is regulated to 0.8V. The current flowing out of this pin is mirrored to the USB charge current control reference. When the USBP pin is connected to logic HIGH, the typical USB charge current can be found as: V REF 0.8V I USB = 45000 ⋅ ------------------ = 45000 × ------------------ ( A ) R IUSB R IUSB The RIUSB has a programming range of 80kΩ to 103kΩ, thus the USB current has a nominal value ranging from 350mA to 450mA. When the USBP pin is driven to logic LOW, the charge current is approximately 1/5 of the above value. USBP (Pin 7) USB port selection logic input. When this pin is left floating or driven to logic LOW, the USB port is regarded as a low-power port, in such case the charge current is 100mA maximum. When this pin is driven to logic HIGH, the USB port is considered a high-power port, and the charge current is 500mA maximum. The ratio of the charge current when this pin is HIGH or LOW is fixed at approximately 5:1. GND (Pin 8) System ground. ICDL (Pin 9) The ICDL pin has two functions. The first function is to program the cradle charge current during the constantcurrent phase. The voltage of this pin is 1.20V during the constant-current phase of the cradle input charger. The constant-current is programmed by the following equation: 1.20V I CDL = ----------------- ⋅ ratio R ICDL (A) where RICDL is the resistor connected to the ICDL pin (see Typical Application). The ratio is given by the following table and curve. 6 1220 RATIO IUSB (Pin 6) 1190 1160 1130 1100 1070 1 2 3 RICDL (kΩ) 4 5 FIGURE 1. THE RATIO USED IN THE CHARGE CURRENT CALCULATION vs. RICDL The second function of the ICDL pin is to monitor the actual charge current. The voltage of this pin, VICDL, is proportional to the actual charge current, ICHG, in either the USB or the cradle charger. When the cradle charger or the USB charger is working with USBP connected to logic HIGH, the ICDL pin voltage is given by the following equation: R ICDL ⋅ I CHG 1.20V V ICDL = ---------------- ⋅ I CHG = ----------------------------------I CDL ratio where the ratio has the same value given in Table 1. The cradle charge current should be programmed equal or higher than the USB current; otherwise, the ICDL pin voltage will be higher than 1.20V during the constant current phase when the USB charger is working. The charger still works properly but the accuracy of the current monitoring voltage degrades and saturates at approximately 2.1V. When the USB charger is working with the USBP pin connected to logic LOW, the ICDL pin voltage is approximately five times of the above equation. BAT (Pin 10) Charger output pin. Connect this pin to the battery pack or the battery cell. A 1µF or larger value ceramic capacitor is recommended for decoupling. The charger relies on the battery for stability so a battery should always be connected to the BAT pin. FN9180.1 January 4, 2006 ISL6293 Description Floating Charge Voltage The ISL6293 is designed for a single-cell Li-ion or Li-polymer battery charging circuit that accepts both a USB port and a desktop cradle as its power source. The charge current from each power source is independently programmable but only one of the two sources charges the battery. The following describes the operation of the charger. The floating voltage during the constant voltage phase is 4.2V. The floating voltage has an 1% accuracy over the ambient temperature range of -40°C to 70°C. Input Auto Selection When both input sources are present, the charger selects only one power source to charge the battery. When the CRDL input is higher than both the POR threshold and the battery voltage, CRDL is selected as the power source. Otherwise the USB input is selected. If the CRDL input voltage is below the battery voltage but the USB input voltage is higher than the battery voltage, then the USB input is used to charge the battery. The control circuit always breaks both internal power devices before switching in one power source to avoid any simultaneous conduction of both power MOSFETs. When the BAT pin voltage is below 1.7V, the charger selects the CRDL input as the power source. Hence, if the USB input is powered, the charger will not charge the battery. Trickle Charge Current When the battery voltage is below the minimum battery voltage VMIN given in the electrical specification, the charger operates in a trickle/preconditioning mode. If power comes from the cradle, the trickle mode current is 1.20V I TRICKLE = ----------------- ⋅ 100 R ICDL (A) The trickle current is 45mA if the power comes from the USB port with RIUSB = 80kΩ. End-of-Charge Indication The CHG pin outputs a logic HIGH by turning off the internal open-drain MOSFET when the charge current falls below 8% of the constant current mode current for the cradle input or 10% for the USB input when RIUSB is 80kΩ. The charger, however, does not turn off as long as an input power source is attached. Power Presence Indication USB Charge Current When the USB port is selected as the power source, the charge current is programmed by the logic input USBP pin. With the RIUSB selected at 80kΩ, when the USBP is driven to logic LOW, the charge current is set to 90mA. When the USBP is driven to logic HIGH, the charge current is set to 450mA. The USBP is equivalent to a logic LOW when left floating. Typically the P-channel MOSFET for the USB input has an rDS(ON) of 700mΩ at room temperature, thus with a 500mA charge current, the typical head room is 350mV. If the input voltage drops to a level that the voltage different between the USB pin and the BAT pin is less than 350mV, the rDS(ON) becomes a limiting factor of the charge current and the charge current drops out the constant current regulation. When either the USB or the cradle input voltage is above the POR level, the PPR pin outputs a logic LOW signal to indicate the presence of input power. Cradle Charge Current The cradle charge current is programmed with the external resistor connected between the ICDL pin and the GND pin. The current can be calculated with the equation given in the ICDL pin description. The typical rDS(ON) value of the Pchannel MOSFET for the CRDL input is 700mΩ at room temperature, thus when the head room between the input and output voltages is small, the actual charge current, similar to the USB case, could be limited by the rDS(ON). On the other hand, if the head room between the input and output voltages is large, the charge current maybe limited by the thermal foldback threshold due to the increased power dissipation. 7 FN9180.1 January 4, 2006 ISL6293 Dual Flat No-Lead Plastic Package (DFN) 2X 0.15 C A D A L10.3x3 10 LEAD DUAL FLAT NO-LEAD PLASTIC PACKAGE MILLIMETERS 2X 0.15 C B E 6 INDEX AREA SYMBOL MIN 0.80 0.90 1.00 - - - 0.05 - 0.28 5,8 2.05 7,8 1.65 7,8 0.20 REF 0.18 D 1.95 E SIDE VIEW C SEATING PLANE A3 1 e 1.60 - 0.50 BSC - k 0.25 - - L 0.30 0.35 0.40 N 10 Nd 5 8 2 3 1. Dimensioning and tolerancing conform to ASME Y14.5-1994. 2. N is the number of terminals. NX k E2/2 N-1 7. Dimensions D2 and E2 are for the exposed pads which provide improved electrical and thermal performance. NX b 5 (Nd-1)Xe REF. 4. All dimensions are in millimeters. Angles are in degrees. 6. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 identifier may be either a mold or mark feature. NX L e 3. Nd refers to the number of terminals on D. 5. Dimension b applies to the metallized terminal and is measured between 0.15mm and 0.30mm from the terminal tip. E2 8 1.55 NOTES: D2/2 2 N - Rev. 3 6/04 D2 (DATUM B) 2.00 8 7 6 INDEX AREA (DATUM A) 0.08 C - 3.00 BSC E2 0.10 C 0.23 3.00 BSC D2 A NOTES A A3 B MAX A1 b TOP VIEW NOMINAL 0.10 M C A B 8. Nominal dimensions are provided to assist with PCB Land Pattern Design efforts, see Intersil Technical Brief TB389. BOTTOM VIEW C L 0.415 NX (b) (A1) 0.200 5 L NX L e SECTION "C-C" C NX b C C TERMINAL TIP FOR ODD TERMINAL/SIDE All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 8 FN9180.1 January 4, 2006