RSS

RT9073N-33GB
Evaluation Board
your power partner.
1µA IQ, 250mA Low-Dropout Linear Regulator
Purpose
The RT9073 is a low-dropout (LDO) voltage regulators with enable function that operates from 1.2V to 5.5V. It
provides up to 250mA of output current and offers low-power operation in miniaturized packaging.
The features of low quiescent current as low as 1µA and almost zero disable current is ideal for powering the battery
equipment to a longer service life. The RT9073 is stable with the ceramic output capacitor over its wide input range
from 1.2V to 5.5V and the entire range of output load current (0mA to 250mA).
Table of Contents
Purpose ................................................................................................................................................................. 1
Introduction............................................................................................................................................................ 2
Key Performance Summary Table .......................................................................................................................... 2
Bench Test Setup Conditions ................................................................................................................................. 3
Schematic, Bill of Materials & Board Layout ........................................................................................................... 4
More Information.................................................................................................................................................... 6
Important Notice for Richtek Evaluation Board ....................................................................................................... 6
EVB_RT9073N-33GB-00
December 2015
1
http://www.richtek.com
RT9073N-33GB
Evaluation Board
your power partner.
Introduction
General Product Information
The RT9073 is a low quiescent current linear regulator designed especially for low external components system.
The input voltage range is from 1.2V to 5.5V. The RT9073 builds in a P-MOSFET output transistor which provides a
low switch-on resistance for low dropout voltage applications.
The Error Amplifier compares the internal reference voltage with the output feedback voltage from the internal
divider, and controls the Gate voltage of P-MOSFET to support good line regulation and load regulation at output
voltage.
Product Feature

1µA Ground Current at no Load

PSRR = 75dB at 1kHz

Adjustable Output Voltage Available by Specific Application

±2% Output Accuracy

250mA (VIN ≥ 2.3V) Output Current with EN

Low (0.1µA) Disable Current

1.2V to 5.5V Operating Input Voltage

Dropout Voltage : 0.5V at 250mA when VOUT ≥ 3V

Support Fixed Output Voltage 3.3V

Stable with Ceramic or Tantalum Capacitor

Current Limit Protection

Over Temperature Protection

SOT-23-5 Packages Available
Key Performance Summary Table
Key Features
Evaluation Board Number : PCB041_V1
Input Voltage Range
1.2V to 5.5V
Output Current Limit
350mA
Power Supply Rejection Ratio
75dB
Default Marking & Package Type
RT9073N-33GB, SOT-23-5
VCC Consumption Current
1µA
EVB_RT9073N-33GB-00
December 2015
2
http://www.richtek.com
RT9073N-33GB
Evaluation Board
your power partner.
Bench Test Setup Conditions
Headers Description and Placement
Please carefully inspect the EVB IC and external components, comparing them to the following Bill of Materials, to ensure that all components are
installed and undamaged. If any components are missing or damaged during transportation, please contact the distributor or send e-mail to
[email protected]
Test Points
The EVB is provided with the test points and pin names listed in the table below.
Test point/
Pin name
Signal
Comment (expected waveforms or voltage levels on test points)
VIN
Input voltage
Input voltage range = 1.2V to 5.5V.
GND
Ground
Ground.
EN
Enable
Enable Control Input.
SNS
Output Voltage Sense point
Output Voltage Sense.
NC
NC
No Internal Connection. (RT9073N only).
VOUT
Output voltage
Default output voltage = 3.3V
Power-up & Measurement Procedure
1. Connect input power (1.2V < VIN < 5.5V) to VIN test pin.
2. VIN/VOUT placed 1µF capacitor.
3. Observe the output voltage is correct.
EVB_RT9073N-33GB-00
December 2015
3
http://www.richtek.com
RT9073N-33GB
Evaluation Board
your power partner.
Schematic, Bill of Materials & Board Layout
EVB Schematic Diagram
Bill of Materials
Reference
Qty
Part Number
Description
Package
Manufacture
U1
1
RT9073N-33GB
Single Output LDO
SOT-23-5
Richtek
C1,C2
2
C1608X7R1C105K
1µF/16V
C-0805
TDK
GP1
1
VIN
SIP-1P-GP
GP2
1
VOUT
SIP-1P-GP
GP3, GP4
2
GND
SIP-1P-GP
R1
1
WR06X1000F
100R
R-0603
WALSIN
R2, R3
2
WR06X1002F
10k
R-0603
WALSIN
R4
1
NC
R-0603
TP1
1
IN
SIP-1P-TP
TP2
1
EN
SIP-1P-TP
Z1, Z2, Z3, Z4
4
SIP-1P-M
SIP-1P-M
Z5, Z6
2
FK_1
FK_1
EVB_RT9073N-33GB-00
December 2015
4
http://www.richtek.com
RT9073N-33GB
Evaluation Board
your power partner.
PCB Layout
Top View
Bottom View
EVB_RT9073N-33GB-00
December 2015
5
http://www.richtek.com
RT9073N-33GB
Evaluation Board
your power partner.
More Information
For more information, please find the related datasheet or application notes from Richtek website
http://www.richtek.com.
Important Notice for Richtek Evaluation Board
THIS DOCUMENT IS FOR REFERENCE ONLY, NOTHING CONTAINED IN THIS DOCUMENT SHALL BE CONSTRUED AS RICHTEK’S WARRANTY, EXPRESS
OR IMPLIED, UNDER CONTRACT, TORT OR STATUTORY, WITH RESPECT TO THE PRESENTATION HEREIN. IN NO EVENT SHALL RICHTEK BE LIABLE T O
BUYER OR USER FOR ANY AND ALL DAMAGES INCLUDING WITHOUT LIMITATION TO DIRECT, INDIRECT, SPECIAL, PUNITIVE OR CONSEQUENTIAL
DAMAGES.
EVB_RT9073N-33GB-00
December 2015
6
http://www.richtek.com