www.osram.com/lightify-pro LIGHTIFY Pro Commissioning and control via Smart Device (Tablet / Smart Phone) Welcome to LIGHTIFY Pro Page 1. LIGHTIFY Pro – System overview and operating principle 3 2. Installation information 4 3. Setup – First steps 5 4. Configuration with the LIGHTIFY Pro Commissioning App 7 4.1. How to connect the LIGHTIFY Pro Gateway 7 4.2. Configuration menu and functions 8 4.2.1. Dashboard (System overview) 8 4.2.2. Functions 9 4.2.2.1. Scan (Add new network devices) 9 4.2.2.2. Identify (Identify network endpoints) 10 4.2.2.3. Canvas (System configuration interface) 11 4.2.2.4. QR Codes (User access configuration) 12 4.2.2.5. Network diagnostics (Check of network quality) 12 4.2.2.6. Disconnecting (Disconnect gateway connection) 13 4.2.3. System settings 4.3. Configuration (Setting system parameters) 4.3.1. Activating and setting system parameters 13 14 14 4.3.1.1. Removing existing network devices 14 4.3.1.2. Uploading / using floor plan 15 4.3.1.3. Creating groups 15 4.3.1.4. Saving scenes 15 4.3.1.5. Calling and setting the operating mode 16 4.3.1.6. Activating the group-in group function (swarm) 17 LIGHTIFY Pro installation 1 www.osram.com/lightify-pro Welcome to LIGHTIFY Pro 4.3.2. Device parameter activation and configuration Page 17 4.3.2.1. Parameter setting / change 18 4.3.2.2. Index of available parameters - What / Where / How 19 5. Control with the LIGHTIFY Pro Control App LIGHTIFY Pro installation 22 2 www.osram.com/lightify-pro Welcome to LIGHTIFY Pro Many thanks for purchasing a LIGHTIFY Pro product. For more detailed information about the LIGHTIFY Pro system, including descriptions of use, data sheets and installation information, please see: www.osram.com/lightify-pro 1. LIGHTIFY Pro – System overview and operating principle The LIGHTIFY Pro system contains of hardware and software components Hardware of LIGHTIFY Pro system: • LIGHTIFY Pro Gateway • LIGHTIFY Pro system components LIGHTIFY Pro DSE LIGHTIFY Pro PBC … Software / Apps of LIGHTIFY Pro system: • LIGHTIFY Pro Commissioning App Mandatory to commission LIGHTIFY Pro system ( see chapter 4.) = LIGHTIFY Pro Commissioning App Tablet – iOS 8.x PC – Windows (available later) • LIGHTIFY Pro Control App Mandatory to control LIGHTIFY Pro system ( see chapter 5.) = LIGHTIFY Pro Control App Smart Phone / Tablet – iOS 8.x / Android 4.x PC – Windows (available later) For downloads and further information on available App versions, please visit our homepage: www.osram.com/lightify-pro LIGHTIFY Pro installation 3 www.osram.com/lightify-pro 2. Installation information The installation should be carried out by an authorized electrician. Please see the respective installation information of each LIGHTIFY product! LIGHTIFY Pro installation 4 www.osram.com/lightify-pro 3. Setup – First steps Step 1: Download latest app(s): www.osram.com/lightify-pro and install the app(s) on your Smart Device / PC. = LIGHTIFY Pro Commissioning App Tablet – IOS 8.x PC – Windows (available later) = LIGHTIFY Pro Control App Smart Phone / Tablet – IOS 8.x / Android 4.x PC – Windows (available later) Step 2: Choose from system operating possibilities: Independent use without IT network integration HOTSPOT mode (without Router) OR Integration in an already existing IT network CLIENT mode (with Router) Step 3: Please connect the Gateway, depending on your system operating preference with or without router, and switch it ON. A wireless Gateway connection has to be established as following: HOTSPOT mode (without Router) Connect your Smart Device / PC with the Gateway WIFI. The Gateway WIFI access code will be found on the backside of your Gateway. CLIENT mode (with Router) Connect your Smart Device / PC with the Router WIFI (IT network). For the Router WIFI access code, please contact your IT system administrator. LIGHTIFY Pro installation 5 www.osram.com/lightify-pro 3. Setup – First steps Step 4: Activate the LIGHTIFY Pro Commissioning App and select your Gateway from the list of WIFI / LAN connected Gateways. Step 5: After Gateway selection you will be asked to enter a personal password: During initial commissioning please decide whether to assign password NOW OR to proceed without entering password. (Password assignment can be done at any time later during commissioning please see 4.2.3.: System settings) READY: Now your LIGHTIFY Pro system status will be activated and system commissioning can be started. LIGHTIFY Pro installation 6 www.osram.com/lightify-pro 4. Configuration with the LIGHTIFY Pro Commissioning app 4.1. How to connect the LIGHTIFY Pro Gateway Activate the App and select the gateway to be activated from the list on the left. Please note: ONLY Gateways with established WIFI / LAN connection will be shown! Following activation, all the system parameters are loaded and made available on the graphical user interface. If the Gateway to be activated is not shown, it is possible to establish connection manually. Change between Gateways Please note: If you want to change between Gateways, please make sure to disconnect first from existing Gateway connection before establishing a new connection! Disconnect ( see 4.2.2.6.: Disconnecting) During change process following steps have to be carried out: Please press within the Dashboard on the „Gateway“ symbol in the lower left corner to activate and show list of all WIFI / LAN connected Gateways. Option 1: You activate another Gateway running already in CLIENT mode from the list OR Option 2: You establish a new WIFI connection to another Gateway in HOTSPOT mode and activate this Gateway afterwarts. LIGHTIFY Pro installation 7 www.osram.com/lightify-pro 4.2. Configuration menu and functions By activating the Gateway all system parameters will be transferred and the configuration menu will be shown. a b a) Functions b) System status / Canvas c) Gateways d) Settings e) Information c d e Starting from the configuration menu you are able to choose between different available functions (a) to perform system configuration. b Furthermore you are able to switch from any open canvas to one of the following overviews: b) System status c) Gateways d) Settings e) Information c d e 4.2.1. Dashboard (System overview) The system status (b) will be automatically shown after Gateway activation b AND 1x Press on the function „Dashboard“ top left The Dashboard informs you about: − Floor plan (if already uploaded and used) − System status (e.g. available software updates) − Network status (e.g. reachability of network devices) − Gateway data (e.g. IP address) Direct system control is already available on the Dashboard top right. Installation von LIGHTIFY Pro 8 7 www.osram.com/lightify-pro 4.2.2. Functions Starting from the Dashboard following functions (a) to perform system configuration can be used: a Dashboard (siehe: 4.2.1.) Scan (siehe: 4.2.2.1.) Identify (siehe: 4.2.2.2.) Canvas (siehe: 4.2.2.3.) QR Codes (siehe: 4.2.2.4.) Netzwork Diagnostics (siehe: 4.2.2.5.) Disconnecting (siehe: 4.2.2.6.) Automatic user navigation: Please pay attention to the grafically highlighted and pulsating symbols. 4.2.2.1. Scan (Add new network devices) In the system overview, press Scan. Step 1: Disconnect new devices / network devices Step 2: Select the time for the scan process (Please note: The more devices there are to be read in, the longer the time selected should be) Step 3: Start the scan process Step 4: Switch ON new devices / network devices If the process was aborted during scanning or if devices / network devices could not be correctly identified / read in, restart the scanning process. LIGHTIFY Pro installation 9 www.osram.com/lightify-pro 4.2.2.2. Identify (Identify network endpoints) In the system overview, press Identify. The list on the left shows ALL network endpoints / devices. Newly scanned endpoints / devices will be marked with NEW. You can identify the following 3 product types: 1. Lights (lamps, luminaires) 2. Push-buttons / switches (manual operating interface) 3. Sensors (motion and daylight sensors) Tip: By clicking the symbols you will be informed about the specific operating principle during identification. Now please select the first network endpoint – directly nearby your current location – and start the process. To start identification, press the specific symbol below the dedicated devise type and follow the instructions. First identification completed: If the network device selected has been identified, it can be directly used, renamed and configured. ( see 4.2.2.3.: Canvas) Please note: A network device may contain several configurable end points, e.g. LIGHTIFY Pro DSE see picture on the right Carrying out further identifications: Restart the process to identify other network endpoints / devices. LIGHTIFY Pro installation 10 www.osram.com/lightify-pro 4.2.2.3. Canvas (System configuration interface) In the system overview, press the Canvas. Orientation: LEFT (list): Available network endpoints / devices The view can be changed between "Endpoints" and "Devices" TOP: Display settings The view can be changed between "Groups", "Devices" and "Connections" CENTER: Canvas Main function for configuration, grouping and parametrising of network endpoints / devices BOTTOM: Functions for system configuration "New group", "Selection", "Identification", "Layout" and "Help“ Operating the canvas: Selection of endpoint / device = 1x short press Endpoint / device parameter list = 2x short press Move endpoint / device (drag&drop) Establish a connection = press and hold = draw connection between endpoints / devices with your finger Delete a connection = 1x short press on connection and confirm deletion Configuration of network endpoints / devices: (see 4.3: Configuration) Data saving: Data is automatically saved after each configuration step is implemented. This process is indicated by a data transfer symbol during data saving. LIGHTIFY Pro installation 11 www.osram.com/lightify-pro 4.2.2.4. QR Codes (Creating QR Codes for system control) In the system overview, press QR Codes. Please note: QR Codes determines which functions used by the LIGHTIFY Pro Control App ( see 5.) are enabled. Step 1: Step 2: Press “Add” and name the QR Code Choose your group(s) out of the list provided, which shall be activated for specific QR Code usage. By pressing on each group, select the functions you wish to enable for Control App use and press “Done” The QR code will be generated and it can be shown by pressing the QR symbol behind each QR code name listed. Press “Create PDF” to choose your favored print layout Step 3: Step 4: Step 5: The generated QR code can be read in by any smart device with a camera with use of the LIGHTIFY Pro Control app ( see 5.). The functions enabled by the system permissions are automatically made available for use on the smart device used. 4.2.2.5. Network diagnostics (Check of network quality) In the system overview, press Network diagnostics. The network diagnostics will be started automatically and the network quality shown by colored status symbols for each existing connection between network devices. Status symbols: Green - connection / signal available Orange - connection / signal is moderate Red - no connection / signal Please note: The diagnostics will be executed for existing network devices ONLY. Devices not scanned yet or belonging to another network will not be considered. LIGHTIFY Pro installation 12 www.osram.com/lightify-pro 4.2.2.6. Disconnecting (Disconnect gateway connection) In the system overview, press Disconnecting Establishing a new Gateway connection: see 4.1.: How to connect the LIGHTIFY Pro Gateway 4.2.3. Settings In the system overview, press Settings Set Commissioning Password This function enables you to assign or change system password of the connected Gateway. Configuration Backup This function enables you to save all configuration data as backup on an USB stick. Configuration Restore This function enables you to recover a system configuration backup. Print System Report This function enables you to print a complete report of the system configuration. Firmware Updates This function enables you to download / install new firmware to your system devices. Step 1: Download Firmware Updates from the internet first Please note: Internet connection required! Step 2: Install Firmware Updates to your system components System Maintenance This function enables you to reload / rediscover / reset / fix system data. ATTENTION! The System Maintenance functions can change or delete ! your system settings. LIGHTIFY Pro installation 13 www.osram.com/lightify-pro 4.3. Configuration (Setting system parameters) The configuration of individual network devices is implemented in the canvas. ( see 4.2.2.3: Canvas (System configuration interface) 4.3.1. Activating and setting system parameters In the system overview, press the Canvas. Operating the canvas: Selection of endpoint / device = 1x short press Endpoint / device parameter list = 2x short press Move endpoint / device (drag&drop) = press and hold Establish a connection = draw connection between endpoints / devices with your finger Delete a connection = 1x short press on connection and confirm deletion Please note: Different network devices will show different parameter lists in regard to their implemented functions. Data saving: Data is automatically saved after each configuration step is implemented. This process is indicated by a data transfer symbol during data saving. 4.3.1.1. Removing existing network devices Step 1: Activate the parameter list (2x short press) of device, which shall be removed / deleted from canvas. Step 2: Please note: Choose between: a) „Remove from Canvas“ to remove device from configuration interface – Device still exist in network! b) „Delete from Network“ to delete device out of the network – Device will be reseted and can be used in another network! LIGHTIFY Pro installation 14 www.osram.com/lightify-pro 4.3.1.2. Uploading / using floor plan Important: Useable data formats: PDF, JPG, GIF Step 1: Copy floor plan to an existing USB stick and connect stick to USB input on Gateway Step 2: Select “Floor Plan” in Canvas and upload floor plan from USB stick 4.3.1.3. Creating groups Step 1: Via drag & drop, move the devices to be grouped from the list of network devices onto the Canvas Step 2: Select the end points of the products to be grouped Step 3: Activate the "Select" function and select "Add to new group“ OR Step 1: Via drag & drop, move the devices to be grouped from the list of network devices onto the Canvas Step 2: Activate the "New group" function Step 3: Connect the end points of the products to be grouped with the newly established 4.3.1.4. Saving scenes Please note: Scenes are saved at group level. a) Assign a scene to a complete group b) Assign a scene to an endpoint / device within a group a) Assign a scene to a complete group: Step 1: Activate the parameter list (2x short press) of the group for which the scene is intended Step 2: Select "Control light" Step 3: Configure the light setting according to your requirements and press "New scene from current settings" Step 4: Name the scene that is then automatically saved with the assigned name LIGHTIFY Pro installation 15 www.osram.com/lightify-pro b) Assign a scene to an endpoint / device within a group: Step 1: Activate the parameter list (2x short press) of the end point / product for which the scene is intended Step 2: Select "Control light" Step 3: Configure the light setting according to your requirements Step 4: Activate the parameter list (2x short press) of the group containing the end point / product Step 5: Select "Scene management" in the parameter list Step 6: Add a scene to the list and name the scene. It will be automatically saved under the assigned name Please note: All saved scenes can be displayed, edited and activated under "Scene management" in the parameter list. 4.3.1.5. Calling and setting the operating mode Step 1: Activate the parameter list (2x short press) of the group for which the operating mode is intended Step 2: Select "Operating mode" Step 3: Select "Display selection" for the following pre-configured operating modes: 1. Office 4. Staircase 2. Meeting room 5. Sanitary room 3. Corridor 6. Classroom OR Configure the required operating mode yourself by using the parameter list: Step 4: 1. ON-Time (T1) 3. Hold-Time (T2) 2. ON-Level 4. Hold-Level Activate / deactivate additional functions in the parameter list: Semi-automatic = manual switch-on required via push-button / switch Staircase function = light signal / power dip shortly before switch-off Please note: Activated parameters and functions during operating mode setting will be saved automatically after exiting the parameter list. LIGHTIFY Pro installation 16 www.osram.com/lightify-pro 4.3.1.6. Activate the group-in-group function (swarm) Please note: A group-in-group function is based on a minimum of 2 single groups. Each single group must still be individually configured, but can be additionally integrated into a higher-level group (swarm group) for higher-level functions, e.g. central ON/OFF for all groups via single Switch/Push-button. Step 1: Establish at least 2 groups ( see: 4.3.1.3.: Creating groups) Step 2: Activate the "New group" function Step 3: Connect the already created groups with the newly created swarm group Step 4: Activate the parameter list (2x short press) of the swarm group Step 5: Activate "Swarm mode" in the parameter list Please note: The single-groups in the swarm still keep their parameter settings as long as they are not modified on single-group level. 4.3.2. Device parameter activation and configuration Please note: Activation of devices / network devices is a group function, means creating a group before activating certain devices is necessary first hand ( see: 4.3.1.3.: Creating groups) and this group has to be connected to min. 1 light point (lamp, luminaire). Step 1: Via drag & drop, move the device to be grouped from the list of network devices onto the Canvas OR Use already existing device endpoints on canvas Step 2: Connect the end points of the products to be activated with the newly created group or an existing group Step 3: Activate the parameter list (2x short press) for required configuration settings LIGHTIFY Pro installation 17 www.osram.com/lightify-pro Device parameters and group parameters Please note: It is important to distinguish between device parameters and group parameters as they will influence the system / network differently. Device parameters: Will effect only the device on which the parameter list had been activated. Group parameters: Will have effect on the group and therefore on one or more devices connected to this group. 4.3.2.1. Parameter setting / change Please note: A device can have more than one configurable endpoint see picture on the right Parameter setting: Step 1: Step 2: Step 3: Activate the parameter list (2x short press) of the endpoint to be set up. Select the parameter out of the list provided. Change parameter value as required within the provided value range. Data saving: Data is automatically saved after leaving the parameter list and started with immediate effect. This process is indicated by a data transfer symbol during data saving. LIGHTIFY Pro installation 18 www.osram.com/lightify-pro 4.3.2.2. Index of available parameters - What / Where / How What: Where: How: Firmware updates for network devices 1st option: Dashboard 2nd option: Settings 1x short press: „Firmware updates“ System configuration – Backup / restore Settings 1x short press: „Configuration Restore“ / „Configuration Backup“ System password – Setup / change Settings 1x short press: „Set Commissioning Password“ System report – Print Settings 1x short press: „Print System Report“ System maintenance Settings 1x short press: „System maintenance“ WIFI password Backside of Gateway WPA2 Key: xxxxxxxx Gateway Light point (luminaire / lamp) Device name / light name – Setup / change Canvas 2x short press: Light point symbol 1x short press: „Light Name“ or „Device Name“ Light point (luminaire / lamp) switching / dimming / change Canvas 2x short press: Light point symbol 1x short press: „Control Light“ Push-buttons / switches and coupler Device name – Setup / change Canvas 2x short press: Switch symbol 1x short press: „Control Name“ or „Device Name“ Device configuration – Act as push-button or switch Canvas 2x short press: Switch symbol „Should act as Button = NO/YES“ LIGHTIFY Pro installation 19 www.osram.com/lightify-pro 4.3.2.2. Index of available parameters - What / Where / How What: Where: How: Push-buttons / switches and coupler Push-button / Switch – Activation / Deactivation Canvas 2x short press: Switch symbol „Enabled = OFF/ON“ Push-button / Switch – Input monitoring Canvas 2x short press: Switch symbol „Input Monitoring = OFF/ON“ Canvas 2x short press: Switch symbol 1x short press: „Short Press Actions“ / „Long Press Actions “ Push-button / Switch – Short & long press actions Sensors based on movement and daylight detection Device name – Setup / change Canvas 2x short press: Movement / daylight symbol 1x short press: „Control Name“ or „Device name“ Sensors – Activation / Deactivation Canvas 2x short press: Movement / daylight symbol „Enabled = OFF/ON“ Sensor MOVEMENT – Input monitoring Canvas 2x short press: Movement / daylight symbol „Input Monitoring = OFF/ON“ Sensor MOVEMENT – Detection range / sensitivity 1st option: HF sensor = Canvas 2nd option: PIR sensor = Range ONLY mechanically adjustable! HF sensor: 2x short press: Movement symbol „Detection Range = -5 to +5“ / „Vibration Sensitivity = OFF to MAX“ PIR sensor: ONLY mechanical adjustment at sensor lense possible! Sensor „DAYLIGHT“ – Activation / Deactivation of automatic daylight regulation Canvas Group function: 1x short press: Group symbol „Light Regulation = OFF/ON“ Sensor „DAYLIGHT“ – Light level Canvas 2x short press: Daylight symbol „Actual Level = xx%“ LIGHTIFY Pro installation 20 www.osram.com/lightify-pro 4.3.2.2. Index of available parameters - What / Where / How What: Where: Sensors based on Sensor DAYLIGHT – Light level setup LIGHTIFY Pro installation How: movement and daylight detection Canvas 1st option: Store light level 2nd option: Set target level Group function: Store light level: 1x short press: Group symbol 1x short press: Control Group Adjust light level 1x short press: „Store light level for daylight regulation“ Set target level: 1x short press: Group symbol 1x short press: Light Regulation 1x short press: A. Set to current light level B. Target level 21 www.osram.com/lightify-pro 5. Control with LIGHTIFY Pro Control App In this chapter the LIGHTIFY Pro system control is shown by using the LIGHTIFY Pro Control App. Open the app on your smart device. Functions and control Please note: ONLY QR codes created by the LIGHTIFY Pro Commissioning App can be used see 4.2.2.4.: QR Codes Step 1: Access the LIGHTIFY Pro Control App. a) During first use of App the scan function will be started automatically and the camera activated. Scan a QR-Code. b) If QR codes had been scanned and saved already, they will be shown after App access is granted. Choose a QR-Code out of the list provided. Please note: A QR code created by using the LIGHTIFY Pro Commissioning App contains ALL light groups and their respective x light functions enabled during the commissioning process and they y will automatically made available for control on the smart device used. Control menu: z x) Information y) Adding QR Codes z) List of already scanned QR Codes LIGHTIFY Pro installation 22 www.osram.com/lightify-pro Step 2: Select a QR code (= light group) to open the respective light functions available. ALL enabled light functions for this group will be shown under the group name in symbolic order. Step 3: Control your light installation by operating the intuitive user interface. Please note: The LIGHTIFY Pro Control App can only be used to control the light installation. Requested changes on control functionality or a re-commissioning of the light installation has to be done by using the LIGHTIFY Pro Commissioning App. After re-commissioning a new QR code has to be created to ensure activation of new light functions on your smart device! LIGHTIFY Pro installation 23