ML Series Instructions

CONDOR DC POWER SUPPLIES INC.
2311 STATHAM PKWY
OXNARD, CA 93033 + 805-486-4565
ML SERIES
INSTALLATION INSTRUCTIONS
RATINGS:
Input: 100-120/220-240 V ac, 0.2/0.1 A, 50/60 Hz
Derate output current 10% for operation at frequencies below 58 Hz.
Output:
MODEL
ML5-1/OVP-A
ML12-0.5-A
ML15-0.4-A
ML24-0.28-A
MLL12-0.25-A
MLL15-0.2-A
MTLL-5W-A
Notes: 1.
2.
3.
OUTPUT
Secondary Fuse Values
5V 1.0A
F1 = 2.0A SB
12V 0.5A
F1 = 1.0A SB
15V 0.4A
F1 = 0.75A SB
24V 0.28A
F1 = 0.5A SB
±12V 0.25A
F1, F3 = 0.5A SB
±15V 0.2A
F1, F3 = 0.5A SB
+5V 0.5A
F1 = 1.0A SB
±12V or ±15V 0.1A
F3 = 0.5A SB
Maximum ambient temperature for continuous output specified in the table is 50°C.
Maximum Operating Relative Humidity 96%, no condensation.
Maximum output short circuit current is 150% of rated output current.
CERTIFICATION: All models are Certified to be in compliance with the applicable requirements of UL 2601-1, 1st Ed;
CSA 22.2 No. 234 (level 3); EN 60601-1:1988.
CLASSIFICATION: (5.1) Protection against electric shock = Class II
(In accordance with subclause 5 of IEC 601-1)
(5.2) Degree of protection against electric shock = Not acceptable for applied part without
additional isolation (contact factory for details)
(5.3) Protection against harmful ingress of water = Ordinary (no protection)
(5.5) Have not been evaluated for use in the presence of a flammable anaesthetic mixture with
air, oxygen, or nitrous oxide. This evaluation is to be made on the end equipment by the OEM.
(5.6) Mode of operation = Continuous
ISOLATION: The creepage distance between primary and secondary circuits is 8 mm minimum. The
required creepage and clearance distances from primary circuits to ground and secondary circuits must
be maintained after installation to preserve the intended safety.
OUTPUTS: All output commons should be connected to Protective Earth in the end application. The
output(s) are intended for Protectively Earthed Signal Output and Intermediate Circuits only. The
output(s) have not been investigated for patient connection. All DC outputs are SELV under normal and
single fault conditions.
OVERVOLTAGE PROTECTION: The output is monitored for an overvoltage condition. In some
applications where an overvoltage condition could result in a hazard as defined in applicable safety
standards, redundant or additional overvoltage protection may be required. Consult factory for details.
TEMPERATURES: The maximum operating temperatures of certain safety components, as defined in
the applicable safety standards, must not be exceeded after installation to preserve the intended safety.
The output power, ambient air temperature and the availability, amount, direction and/or restriction of
airflow influence the temperatures of these components.
41-32512-0001 Rev. F 9/26/03
Page 1 of 2
ML SERIES INSTALLATION INSTRUCTIONS
OVERCURRENT PROTECTION: EN 60601-1 requires that both supply leads (phase and neutral)
be protected against overcurrent. Complete overcurrent protection must be provided in the host
equipment. Fuse ratings must not exceed 0.25 A for 120 V or 0.125 A for 240 V, must meet the
requirements of EN 60601-1 and be acceptable for the country in which the host equipment is to be
installed.
WARNING! RISK OF FIRE! A blown fuse is an indication of catastrophic failure of circuit
component(s). Repair must be performed by Condor authorized personnel. Refer to fuse markings
above or on unit for rating.
WARNING! SHOCK HAZARD! Dangerous voltages are present on some components, printed wiring
traces and heatsinks.
EXPLANATION OF SYMBOLS
Alternating Current
Direct Current
Attention, Consult
Accompanying Documents
AC INPUT CONNECTIONS
7
5
3
100-120V
1
7
5
3
1
200-240V
Mating Connector, Housing: Amp P/N 640250-7 or equiv.
Mating Connector, Contact: Amp P/N 640706-1 or equiv.
DC OUTPUT CONNECTIONS
Pin
1
2
3
4
5
Single Output
N/C
Common
+ Output
Common
N/C
Dual Output
+ Output #1
Common
N/C
Common
– Output #2
Triple Output
+ Output #2
Common
+ Output #1
Common
– Output #3
Mating Connector, Housing: Amp P/N 640250-5 or equiv.
Mating Connector, Contact: Amp P/N 640706-1 or equiv.
Condor DC Power Supplies Inc. will not be liable for the safety, reliability or performance of these power supplies if a) any changes, modifications or repairs are carried out by other
than authorized agents of Condor DC Power Supplies Inc., or b) the installation of the supply is not in accordance with these installation instructions and the applicable UL, CSA,
and EN/IEC safety standards.
41-32512-0001 Rev. F 9/26/03
Page 2 of 2