NSVS999

NSVS999 Apr. 2013
NewJRC SAW FILTER
NSVS999
Application
GPS L5
Electrical Specification: (Table 1)
The device characteristics are measured in the circuit shown in Fig.1.
Table 1. Electrical Specifications
Item
Input and Output Impedance
Nominal Center Frequency (f0)
Insertion Loss
1166.45~1186.45MHz
Response Variation
1166.45~1186.45MHz
Input and Output VSWR 1166.45~1186.45MHz
Out of Band Rejection
1121.45MHz
(Relative to
1231.45MHz
Through Level)
Spec.
3.5dB max.
1.5dB max.
1.5 max.
Typical
50Ω
1176.45MHz
3.0dB
1.0dB
2.0
30dB min.
40dB
30dB min.
35dB
(Operating Temperature Range : -30~+85ºC)
Maximum Rating: (Table 2)
Table2. Maximum Ratings
Item
Maximum Input Power
Maximum DC Voltage
Operating Temperature Range
Storage Temperature
Rating
+10dBm
7.5V
-30~+85ºC
-40~+90ºC
Mechanical Specifications: (Fig.2)
Package is designed as small as 3.0x3.0x1.15[mm3] for SMD (Surface Mount Device) type.
Notice:
This part is electrostatic discharge sensitive and may be damaged by improper handling.
http://www.njr.co.jp/products/device/index.html
http://www.njr.com/products/device/index.html
(Japanese)
(English)
NSVS999 Apr. 2013
1
6
2 SAW 5
IN
50Ω
3
4
OUT
50Ω
Fig.1 Measuring circuit
(a)
3. 0±0. 15
( b)
3. 0 ± 0. 1 5
221
( c)
OP
(1)
( 0. 6)
( 0. 2 5)
1. 1 5 ± 0. 1 5
( 2)
4
( 0. 6)
[ 2 x]
3
2
5
( 1. 80)
1
( 0. 75)
( 0. 45)
[ 4x]
( 0. 5 3)
[ 4 x]
6
Fig.2 Package dimensions (in mm)
0.93
3.8
1.15
3.8
0.6
2.2
0.93
1.15
Fig.3 Desirable land area (in mm)
Marking
(1) Lot Number
(a) Year
(b) Month
*Oct.--Nov.--Dec.--(c) Date
1-9--10-19--20-31--(2) Part Number Mark
Pin no.
1
2
3
4
5
6
Connection
GND
IN/OUT
GND
GND
OUT/IN
GND
X
Y
Z
0
1
2
NSVS999 Apr. 2013
Notice
1. Use this component within operating temperature range. It might not be
satisfied with electrical specification without operating temperature range.
When it is used less than -30ºC or more than +85ºC, it might be a cause of
degradation or destruction of the component. Even if it endures during a short
time, it causes degradation of qualification.
2. When soldering iron is used, solder with the temperature at the tip of soldering
iron: 350ºC max., the time of soldering: 10 seconds max., the power of
soldering iron: 30W max..
3. Notice that the allowed time of soldering with soldering iron is accumulated
time, when soldering is repeated.
4. As rapid temperature change for cleaning after reflow soldering might be a
cause of destruction clean this component after confirming that temperature of
this component goes down to room temperature.
5. Confirm that there are not any influence for qualification to this component in
mounting on PCB when this component is cleaned.
6. As it might be a cause of degradation of destruction to apply static electricity to
this component, do not apply static electricity or excessive voltage while
assembling and measuring. And do not transport this component with bare
hand.
7. As it might be a cause of degradation or destruction to apply D.C. voltage
between each terminal, apply D.C. voltage 7.5V max. in actual circuit.
Note
1. This specification specifies the quality of this component as a single unit. Make
sure that this component is evaluated and confirmed against this specification
when it is mounted to your products.
NSVS999 Apr. 2013
Insertion Loss [dB]
0
FREQUENCY CHARACTERISTICS
0
10
2
20
4
30
6
40
8
50
10
CH1 : center 1176.45 span 200
CH2 : center 1176.45 span 200
S11
S22
S22
11
9
9
VSWR
VSWR
S11
11
7
5
3
7
5
3
1
1076.5
1276.5
1
1076.5
Frequency [MHz]
S21
0
InsertionLoss [dB]
1276.5
Frequency [MHz]
20
40
60
80
100
0
3000
Frequency [MHz]
New Japan Radio Co.,Ltd.
Insertion Loss [dB]
S21