NSVS872

NSVS872 Apr. 2013
NewJRC SAW FILTER
NSVS872
Application
314MHz R.K.E.
Electrical Specification: (Table 1)
The device characteristics are measured in the circuit shown in Fig.1.
Table 1. Electrical Specifications
Item
Spec.
Typ.
Input and Output Impedance
50Ω
Nominal Center Frequency (f0)
314MHz
Insertion Loss
313.5~314.5MHz
3.0dB max.
1.5dB
Response Variation
313.5~314.5MHz
1.5dB max.
0.6dB
Input and Output VSWR
313.5~314.5MHz
2.5 max.
1.5
Out of Band Rejection
292.1MHz
50dB min.
60dB
(Relative to Through Level)
334.9MHz
45dB min.
50dB
(Operating Temperature Range: -20~+70ºC)
Maximum Rating: (Table 2)
Table 2. Maximum Ratings
Item
Maximum Input Power
Maximum DC Voltage
Operating Temperature Range
Storage Temperature
Rating
+20dBm
7.5V
-20~+70ºC
-30~+80ºC
Mechanical Specifications: (Fig.2)
Package is designed as small as 3.5x3.5x1.0[mm3] for SMD (Surface Mount Device) type.
Notice:
This part is electrostatic discharge sensitive and may be damaged by improper handling.
http://www.njr.co.jp/products/device/index.html
http://www.njr.com/products/device/index.html
(Japanese)
(English)
NSVS872 Apr. 2013
IN
50Ω
8
1
OUT
50Ω
7
2 SAW 6
3
4
5
Fig.1 Measuring circuit
(a)
3.5±0.2
(1)
(b)
3 .5 ±0 .2
J1Z
TA
(2)
1 .0 ±0 .2
(3)
3
5
[8 x ]
(0.8)
[5x]
4
(0 .6 )
(0.95)
2
6
(1 .0)
[2 x ]
(1 .2 7 )
(2 .5 4 )
(0.6)
1
7
8
Fig.2 Package dimensions (in mm)
4.3
0.8
1.27
4.3
1.27
0.8
[6x]
1.3
[6x]
Via-Hole(Φ 0.3)
Fig.3 Desirable land area (in mm)
Marking
(1) Manufacture’s Mark
(2) Lot Number
(a) Year
(b) Month
*Oct.--- X
Nov.--- Y
Dec.--- Z
(3) Part number Mark
Pin no.
1
2
3
4
5
6
7
8
Connection
GND
IN/OUT
GND
GND
GND
OUT/IN
GND
GND
NSVS872 Apr. 2013
Notice
1. Use this component within operating temperature range. It might not be
satisfied with electrical specification without operating temperature range.
When it is used less than -20ºC or more than +70ºC, it might be a cause of
degradation or destruction of the component. Even if it endures during a short
time, it causes degradation of qualification.
2. When soldering iron is used, solder with the temperature at the tip of soldering
iron: 350ºC max., the time of soldering: 10 seconds max., the power of
soldering iron: 30W max..
3. Notice that the allowed time of soldering with soldering iron is accumulated
time, when soldering is repeated.
4. As rapid temperature change for cleaning after reflow soldering might be a
cause of destruction clean this component after confirming that temperature of
this component goes down to room temperature.
5. Confirm that there are not any influence for qualification to this component in
mounting on PCB when this component is cleaned.
6. As it might be a cause of degradation of destruction to apply static electricity to
this component, do not apply static electricity or excessive voltage while
assembling and measuring. And do not transport this component with bare
hand.
7. As it might be a cause of degradation or destruction to apply D.C. voltage
between each terminal, apply D.C. voltage 7.5V max. in actual circuit.
Note
1. This specification specifies the quality of this component as a single unit. Make
sure that this component is evaluated and confirmed against this specification
when it is mounted to your products.
2. The information contained herein may be changed without prior notice. It is
therefore advisable to contact New Japan Radio Company before proceeding
with the design of equipment incorporating this product.
3.
The products are designed to be used with ordinary electronic equipment (data
and communications equipment, office equipment, audio-video equipment,
measuring instruments, etc). New Japan Radio Company does not assume any
liability for the case using the products with the application required high
reliability or safety extremely (such as space equipment, sea-bottom equipment,
medical equipment etc). When intending to use any our product please contact
our sales representatives in advance.
NS V S 872 Apr . 2013
Ins ertion Los s [dB ]
0
F R E QUE NC Y C HAR AC T E R IS T IC S
0
20
2
40
4
60
6
80
8
100
10
C H1 : center 314 s pan 100
C H2 : center 314 s pan 100
S 11
11
S 22
S 11
11
9
V S WR
V S WR
9
S 22
7
5
3
7
5
3
1
264
364
1
264
Ins ertionLos s [dB ]
F requency [MHz]
0
364
F requency [MHz]
S 21
20
40
60
80
100
0.3
3000
F requency [MHz]
Ins ertion Los s [dB ]
S 21