NSVS776 Apr. 2013 NewJRC SAW FILTER NSVS776 Application 374MHz WLAN Electrical Specification: (Table 1) The device characteristics are measured in the circuit shown in Fig.1. Table 1. Electrical Specifications Parameter Spec. Typ. Input and Output Impedance 50Ω Nominal Center Frequency (f0) 374MHz Insertion Loss 365.5~382.5MHz 12.0dB max. 8.0dB Passband Ripple 366.5~381.5MHz 1.0dB max. 0.8dB Group Delay Ripple 366.5~381.5MHz 100nsec max. 50nsec Out of Band Rejection 274~341MHz 40dB min. 45dB (Relative to Minimum 341~352MHz 40dB min. 42dB Insertion Loss) 352~357.5MHz 35dB min. 37dB 390.5~396MHz 30dB min. 37dB 396~430MHz 35dB min. 37dB 430~474MHz 40dB min. 45dB (Operating Temperature Range: -30~+80ºC) Maximum Rating: (Table 2) Table 2. Maximum Ratings Parameter Maximum Input Power Maximum DC Voltage Operating Temperature Range Storage Temperature Rating +10dBm 7.5V -30~+80ºC -30~+80ºC Mechanical Specification: (Fig.2) Package is designed as small as 5.2x4.5x1.5[mm3] for SMD (Surface Mount Device) type. Notice: This part is electrostatic discharge sensitive and may be damaged by improper handling. http://www.njr.co.jp/products/device/index.html http://www.njr.com/products/device/index.html (Japanese) (English) NSVS776 Apr. 2013 IN 50Ω∗ 27pF 1 8 2 SAW 6 4 5 3 7 22pF OUT 50Ω∗ 15nH 10nH Fig.1 Measuring Circuit 5.2±0.2 (1) (a) (b) 4 .5 ±0 .2 J51 776 (2) 1 .5 ±0 .2 (3) [5x] [2 x ] 1 5 (0 .7 5 ) (1 .2 7 ) 2 (1.27) 3 [8 x ] (1.2) 4 (0 .8 ) (1.55) 6 7 8 Fig.2 Package dimensions (in mm) 6.0 1.0 1.0 [6x] 1.27 5.3 1.27 1.6 [6x] Via-Hole(Φ 0.3) [3x] Fig.3 Desirable land area (in mm) Marking (1) Manufacture’s Mark (2) Lot Number (a) Year (b) Month *Oct.--- X Nov.--- Y Dec.--- Z (3) Part number Mark Pin no. 1 2 3 4 5 6 7 8 Connection GND IN IN GND GND OUT OUT GND NSVS776 Apr. 2013 Notice 1. Use this component within operating temperature range. It might not be satisfied with electrical specification without operating temperature range. When it is used less than -30ºC or more than +80ºC, it might be a cause of degradation or destruction of the component. Even if it endures during a short time, it causes degradation of qualification. 2. When soldering iron is used, solder with the temperature at the tip of soldering iron: 350ºC max., the time of soldering: 10 seconds max., the power of soldering iron: 30W max.. 3. Notice that the allowed time of soldering with soldering iron is accumulated time, when soldering is repeated. 4. As rapid temperature change for cleaning after reflow soldering might be a cause of destruction clean this component after confirming that temperature of this component goes down to room temperature. 5. Confirm that there are not any influence for qualification to this component in mounting on PCB when this component is cleaned. 6. As it might be a cause of degradation of destruction to apply static electricity to this component, do not apply static electricity or excessive voltage while assembling and measuring. And do not transport this component with bare hand. 7. As it might be a cause of degradation or destruction to apply D.C. voltage between each terminal, apply D.C. voltage 7.5V max. in actual circuit. Note 1. This specification specifies the quality of this component as a single unit. Make sure that this component is evaluated and confirmed against this specification when it is mounted to your products. 2. The information contained herein may be changed without prior notice. It is therefore advisable to contact New Japan Radio Company before proceeding with the design of equipment incorporating this product. 3. The products are designed to be used with ordinary electronic equipment (data and communications equipment, office equipment, audio-video equipment, measuring instruments, etc). New Japan Radio Company does not assume any liability for the case using the products with the application required high reliability or safety extremely (such as space equipment, sea-bottom equipment, medical equipment etc). When intending to use any our product please contact our sales representatives in advance. NSVS776 Apr. 2013 FREQUENCY CHARACTERISTICS Insertion Loss [dB] 0 8 10 20 12 30 16 40 20 50 60 24 340 360 380 400 Frequency [MHz] 420 340 360 380 400 Frequency [MHz] 420 Group Delay [ns] 1000 800 600 400 200 0 S11 S22