ENEC LICENCE
Licence No.
Page
Date of Issue
Licence Holder
Production site
Certification Mark
Certified Product
Model
Trademark
Rated Voltage / Frequency
Rated Current / Power
Insulation Class
Degree of protection (IP)
Tested acc. to
Test Report No.
ENEC-01230
1/3
2015-09-30
OSRAM SPA
VIA CASTAGNOLE 65/A
TREVISO, 31100 TV Italy
CHUNG TAK LIGHTING CONTROL SYSTEMS (GUANGZHOU)
LTD
SECOND LIGHT INDUSTRIAL ESTATE
QIAO HING RD, DONG HUAN ST
PANYU
GUANGZHOU, 511400 GUANGDONG China
See Annex 1
Built-in Programmable SELV Constant Current LED controlgear
OT 110/120-277/1A4 2DIMLT2 P
PRI: 220-240 V~, 50/60 Hz, 1060 mA max, λ > 0,95, tc 85 °C
SEC: 600-1400 mA, 35-85 Vd.c. , 110 W max
Max output voltage: 120 Vd.c.
see rated Voltage/Frequency
EN 61347-1:2008/A1:2011, EN 61347-1:2008/A2:2013, EN
61347-1:2008, EN 61347-2-13:2014, EN 62384:2006/A1:2009,
EN 62384:2006
4787022807-2 issued on 2015-09-28, 4787022807-1 issued on
2015-09-28
Additional
Certification Manager
Jan-Erik Storgaard
Certification Body
This is to certify that representative sample(s) of the Product described herein ("Certified Product")
have been investigated and found in compliance with the Standard(s) indicated on this License, in
accordance with the ENEC Requirements. The Designated License holder is entitled to use the ENEC
15 Mark (as shown in annex 1) for the Certified Product manufactured at the production site(s)
identified above in accordance with the ENEC Mark Service Agreement including without limitation
the ENEC Mark Testing and Certification Services Service Terms. Only those Products bearing the
ENEC Mark should be considered as being covered by UL's ENEC Mark Service. This License shall
remain valid unless terminated earlier in accordance with the Service Agreement including without
limitation if the Standard identified on this Certificate is amended or withdrawn prior the Date of
Withdrawal of conflicting Standard(s).
UL International Demko A/S, Borupvang 5A, DK-2750
Ballerup, Denmark, Tel. +45 44 85 65 65, [email protected]
www.ul-europe.com
ENEC LICENCE
Licence No.
Page
Date of Issue
ENEC-01230
2/3
2015-09-30
Rated Voltage Frequency:
PRI: 220-240 V~, 50/60 Hz, 1060 mA max, λ > 0,95, tc 85 °C
SEC: 600-1400 mA, 35-85 Vd.c. , 110 W max
Max output voltage: 120 Vd.c.
Additional Information:
Insulation:
Equipotential terminal (metal housing) is reinforced insulated from primary circuit (protective impedance) and may
be connected to PE for reasons other than safety. Metal housing is touch safe in class II luminaire.
1-10 V is basic insulated from primary circuit, and has supplementary insulation from secondary circuit.
Output terminals (SEC on rating label) are reinforced insulated from primary circuits.
Certification Body
This is to certify that representative sample(s) of the Product described herein ("Certified Product") have been investigated
and found in compliance with the Standard(s) indicated on this License, in accordance with the ENEC Requirements. The
Designated License holder is entitled to use the ENEC 15 Mark (as shown in annex 1) for the Certified Product
manufactured at the production site(s) identified above in accordance with the ENEC Mark Service Agreement including
without limitation the ENEC Mark Testing and Certification Services Service Terms. Only those Products bearing the
ENEC Mark should be considered as being covered by UL's ENEC Mark Service. This License shall remain valid unless
terminated earlier in accordance with the Service Agreement including without limitation if the Standard identified on this
Certificate is amended or withdrawn prior the Date of Withdrawal of conflicting Standard(s).
Annex 1 to Licence No.
ENEC-01230
Annex of the form of the Mark
A
* Identification number of the Certification Body
Size of the mark:
The size of the mark may be reduced on the condition that
it remains legible and that the ratio b/a=1,7 is kept
Certification Body
This is to certify that representative sample(s) of the Product described herein ("Certified Product") have been investigated
and found in compliance with the Standard(s) indicated on this License, in accordance with the ENEC Requirements. The
Designated License holder is entitled to use the ENEC 15 Mark (as shown in annex 1) for the Certified Product
manufactured at the production site(s) identified above in accordance with the ENEC Mark Service Agreement including
without limitation the ENEC Mark Testing and Certification Services Service Terms. Only those Products bearing the
ENEC Mark should be considered as being covered by UL's ENEC Mark Service. This License shall remain valid unless
terminated earlier in accordance with the Service Agreement including without limitation if the Standard identified on this
Certificate is amended or withdrawn prior the Date of Withdrawal of conflicting Standard(s).