SPICE

Document 267
SPICE Model – LPS3314
This lumped-element (SPICE) model data simulates the
frequency-dependent behavior of Coilcraft power inductors within the frequency range shown in the accompanying table for each individual inductor.
The data represents de-embedded measurements, as
described below. Effects due to different customer circuit board traces, board materials, ground planes or
interactions with other components are not included and
can have a significant effect when comparing the simulation to measurements of the inductors using other
production verification instruments and fixtures.
vidual lumped element values may be erroneous.
The value of the frequency-dependent variable resistor
RVAR1 is calculated from:
RVAR1 = k1 *
• k1 is shown for each value in the accompanying table.
• f is the frequency in Hz
• RVAR1 is the resistance in Ohms
The value of the frequency-dependent variable resistor
RVAR2 is calculated from:
RVAR2 = k2 *
Lumped Element Modeling Method
Measurements were made using a 50 Ohm impedance
analyzer. Fixture compensation was performed to remove fixture effects. No DC bias current was applied in
any of the measurements. The lumped element values
were determined by optimizing the simulation model to
an average of the measurements. This method results in
a model that represents as closely as possible the typical
frequency-dependent behavior of the component within
the model frequency range.
The equivalent lumped element model schematic is
shown below. Each model should be analyzed only at
the input and output ports. Conclusions based on indi-
• k2 is shown for each value in the accompanying table.
• f is the frequency in Hz
• RVAR2 is the resistance in Ohms
The value of the frequency-dependent inductance LVAR
is calculated from:
LVAR = k3 − k4
* LOG (k5 * f)
• k3, k4, and k5 are shown in the accompanying table.
• f is the frequency in Hz
• LVAR is the inductance in µH
Disclaimer
RVAR2
VAR
C
R2
RVAR1
VAR
R1
LVAR
Coilcraft makes every attempt to provide accurate measurement data and software, representative of our components, in a usable format. Coilcraft, however, disclaims
all warrants relating to the use of its data and software,
whether expressed or implied, including without limitation any implied warranties of merchantability or fitness
for a particular purpose. Coilcraft cannot and will not be
liable for any special, incidental, consequential, indirect
or similar damages occurring with the use of the data
and/or software.
Specifications subject to change without notice.
© Coilcraft, Inc. 2006
Document 267-1 Revised 02/19/03
Document 267
SPICE Model for Coilcraft LPS3314 Power Inductors
Part number
LPS3314-102
LPS3314-222
LPS3314-332
LPS3314-472
LPS3314-562
LPS3314-682
LPS3314-822
LPS3314-103
LPS3314-153
LPS3314-183
LPS3314-223
LPS3314-333
LPS3314-473
LPS3314-563
LPS3314-683
LPS3314-823
LPS3314-104
LPS3314-124
LPS3314-154
LPS3314-184
LPS3314-224
LPS3314-334
LPS3314-474
LPS3314-564
LPS3314-684
LPS3314-824
LPS3314-105
LPS3314-155
Frequency limit
of model (MHz)
Lower Upper
0.1
100
0.1
100
0.1
100
0.1
100
0.1
100
0.1
100
0.1
100
0.1
80
0.1
80
0.1
80
0.1
70
0.1
40
0.1
30
0.1
30
0.1
20
0.1
20
0.1
20
0.1
20
0.1
10
0.1
10
0.1
10
0.1
10
0.1
10
0.1
7
0.1
7
0.1
7
0.1
5
0.1
5
LVAR Coefficients
⏲)
R1 (⏲
450
320
315
165
105
225
205
160
80
50
60
85
160
140
150
200
220
100
120
300
125
260
130
320
270
150
185
185
⏲)
R2 (⏲
0.055
0.100
0.145
0.175
0.220
0.240
0.270
0.330
0.440
0.575
0.720
0.920
1.40
1.55
1.80
2.00
2.75
3.45
4.10
4.80
6.00
9.30
12.0
14.0
18.5
24.0
31.0
44.0
C (pF)
0.860
1.01
0.918
1.01
1.19
1.10
0.975
1.18
1.33
1.35
1.40
1.48
1.49
1.47
1.69
1.56
1.39
1.99
1.84
1.77
2.04
1.90
2.06
1.87
1.89
2.09
2.54
2.30
k1
2.00E-04
1.00E-05
1.00E-05
2.00E-05
5.00E-05
1.00E-05
2.00E-05
4.00E-05
8.00E-05
5.00E-05
1.00E-05
1.00E-05
1.00E-05
1.00E-05
1.00E-05
1.00E-05
1.00E-05
1.00E-05
1.00E-05
8.00E-05
1.00E-05
1.00E-05
1.00E-05
1.00E-05
1.00E-05
1.00E-05
1.00E-05
1.00E-05
k2
k3
0.30
1.0
0.62
2.2
0.91
3.3
1.28
4.7
1.42
5.6
2.00
6.8
2.32
8.2
2.82
10
4.18
15
4.84
18
6.10
22
9.52
33
14.1
47
16.3
56
20
68
23
82
28
100
34
120
40
150
56
180
68
220
97
330
140
470
160
560
215
680
245
820
310
1000
380
1500
Specifications subject to change without notice.
© Coilcraft, Inc. 2006
k4
0.019
0.027
0.036
0.048
0.053
0.075
0.116
0.14
0.22
0.28
0.28
0.28
0.28
0.28
0.31
0.38
0.51
0.91
0.95
1.16
1.53
3.10
3.25
4.18
4.70
6.73
9.21
14.87
k5
9.50E-06
9.80E-06
9.80E-06
9.90E-06
9.90E-06
9.90E-06
9.95E-06
9.95E-06
9.95E-06
9.95E-06
9.95E-06
9.95E-06
9.98E-06
9.98E-06
1.00E-05
1.00E-05
1.00E-05
1.00E-05
1.01E-05
1.01E-05
1.02E-05
1.02E-05
1.05E-05
1.05E-05
1.07E-05
1.08E-05
1.11E-05
1.14E-05
Document 267-54 Revised 11/13/06