SPICE

Document 267
SPICE Model – MSS1048T
This lumped-element (SPICE) model data simulates the
frequency-dependent behavior of Coilcraft power inductors within the frequency range shown in the accompanying table for each individual inductor.
The data represents de-embedded measurements, as
described below. Effects due to different customer circuit board traces, board materials, ground planes or
interactions with other components are not included and
can have a significant effect when comparing the simulation to measurements of the inductors using other
production verification instruments and fixtures.
The value of the frequency-dependent variable resistor
RVAR1 is calculated from:
RVAR1 = k1 *
• k1 is shown for each value in the accompanying table.
• f is the frequency in Hz
• RVAR1 is the resistance in Ohms
The value of the frequency-dependent variable resistor
RVAR2 is calculated from:
RVAR2 = k2 *
Lumped Element Modeling Method
• k2 is shown for each value in the accompanying table.
Measurements were made using a 50 Ohm impedance
analyzer. Fixture compensation was performed to remove fixture effects. No DC bias current was applied in
any of the measurements. The lumped element values
were determined by optimizing the simulation model to
an average of the measurements. This method results in
a model that represents as closely as possible the typical
frequency-dependent behavior of the component within
the model frequency range.
• f is the frequency in Hz
The equivalent lumped element model schematic is
shown below. Each model should only be analyzed at
the input and output ports. Individual elements of the
model are not determined by parameter measurement.
The elements are determined by the overall performance of the lumped element model compared to the
measurements taken of the component.
• k3, k4, and k5 are shown in the accompanying table.
RVAR2
VAR
C
R2
RVAR1
VAR
R1
LVAR
• RVAR2 is the resistance in Ohms
Note: The log function in the following equation is the
natural logarithm, base e, not base 10.
The value of the frequency-dependent inductance LVAR
is calculated from:
LVAR = k3 − k4
• f is the frequency in Hz
• LVAR is the inductance in µH
• LOG is the natural LOG (base e)
Disclaimer
Coilcraft makes every attempt to provide accurate measurement data and software, representative of our components, in a usable format. Coilcraft, however, disclaims
all warrants relating to the use of its data and software,
whether expressed or implied, including without limitation any implied warranties of merchantability or fitness
for a particular purpose. Coilcraft cannot and will not be
liable for any special, incidental, consequential, indirect
or similar damages occurring with the use of the data
and/or software.
Specifications subject to change without notice.
© Coilcraft, Inc. 2010
* LOG (k5 * f)
Document 267-1 Revised 11/20/09
Document 267
SPICE Model for Coilcraft MSS1048T Power Inductors
Part number
MSS1048T-801
MSS1048T-152
MSS1048T-222
MSS1048T-332
MSS1048T-472
MSS1048T-682
MSS1048T-822
MSS1048T-103
MSS1048T-153
MSS1048T-223
MSS1048T-333
MSS1048T-473
MSS1048T-563
MSS1048T-683
MSS1048T-823
MSS1048T-104
MSS1048T-154
MSS1048T-184
MSS1048T-224
MSS1048T-334
Frequency limit
of model (MHz)
Lower Upper
0.1
100
0.1
100
0.1
80
0.1
80
0.1
50
0.1
40
0.1
40
0.1
30
0.1
30
0.1
20
0.1
20
0.1
20
0.1
20
0.1
20
0.1
10
0.1
10
0.1
10
0.1
10
0.1
10
0.1
8
LVAR Coefficients
⏲)
R1 (⏲
375
325
175
200
110
150
100
82
70
62
60
45
45
50
55
48
43
43
52
52
⏲)
R2 (⏲
0.0043
0.0058
0.0072
0.0104
0.0123
0.0180
0.020
0.026
0.041
0.061
0.084
0.130
0.149
0.201
0.227
0.253
0.370
0.450
0.500
0.812
C (pF)
1.60
1.85
3.20
2.76
5.08
4.20
3.90
6.60
5.29
8.60
8.24
5.17
5.51
6.50
7.09
8.07
5.60
6.78
6.46
8.43
k1
3.00E-05
7.00E-05
1.20E-04
1.50E-04
1.50E-04
2.50E-04
2.50E-04
2.50E-04
2.00E-04
2.20E-04
2.40E-04
2.40E-04
2.80E-04
3.00E-04
4.00E-04
9.00E-04
9.00E-04
1.50E-03
1.90E-03
1.70E-03
k2
0.7
1.00
1.20
1.60
1.95
2.25
2.25
3.2
3.8
5.7
8.5
12
14
16
24
32
41
49
60
122
k3
0.8
1.5
2.2
3.3
4.7
6.8
8.2
10
15
22
33
47
56
68
82
100
150
180
220
330
Specifications subject to change without notice.
© Coilcraft, Inc. 2010
k4
0.023
0.023
0.023
0.023
0.026
0.028
0.058
0.068
0.098
0.18
0.37
0.37
0.64
0.82
1.05
1.41
1.80
1.80
2.93
2.93
k5
9.70E-06
9.90E-06
9.90E-06
9.90E-06
9.80E-06
9.50E-06
9.70E-06
9.70E-06
9.80E-06
9.90E-06
6.97E-06
6.97E-06
6.99E-06
7.04E-06
7.12E-06
7.19E-06
7.25E-06
7.54E-06
7.47E-06
8.88E-06
Document 267-58 Revised 11/14/07