1812FS

Document 254-1
Filter Inductors – 1812FS Series
• Magnetically shielded chip inductors
• Provides high performance in transmit and receive filters
• 29 inductance values from 1.0 – 1000 µH
Core material Ceramic/Ferrite
Terminations RoHS compliant silver-palladium-platinum-glass frit.
Weight 0.33 – 0.36 g
Ambient temperature –40°C to +85°C with Irms current
Maximum part temperature +125°C (ambient + temp rise). Derating.
Storage temperature Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 600/7″ reel; 2200/13″ reel. Plastic tape: 12 mm wide,
0.25 mm thick, 8 mm pocket spacing, 3.9 mm pocket depth
PCB washing Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
DCR5 SRF6
%3 Q4max typ Isat7 Irms8
L2
Part number1 (µH) tol min (Ohms) (MHz)(mA) (mA)
1812FS-102_L_1.0
10,530 0.070320 31002950
1812FS-122_L_1.2
10,535 0.110280 28002600
1812FS-152_L_1.5
10,520 0.105200 21002850
1812FS-222_L_2.2
10,530 0.120175 18002700
1812FS-242_L_2.4
10,525 0.175160 19002050
1812FS-272_L_2.7
10,530 0.200165 14002100
1812FS-332_L_3.3
10,533 0.185160 14001900
1812FS-392_L_3.9
10,532 0.195145 13001700
1812FS-472_L_4.7
10,528 0.15 125 10001800
1812FS-562_L_5.6
10,535 0.40 110 10001650
1812FS-682_L_6.8
10,535 0.35 110 8501450
1812FS-103_L_10 10,535 0.55 90 7101400
1812FS-153_L_15 10,540 0.75 75 6801150
1812FS-223_L_22 10,545 0.85 15 600 855
1812FS-333_L_33 10,545 1.1
10 540 820
1812FS-393_L_39 10,545 1.1
9.8 500 710
1812FS-473_L_47 10,545 1.2
8.0 390 645
1812FS-683_L_68 10,545 1.8
14.2 260 650
1812FS-104_L_100 10,545 2.5
4.5 260 520
1812FS-154_L_150 10,540 3.8
3.4 220 475
1812FS-224_L_220 10,545 5.4
3.0 180 390
1812FS-274_L_270 10,535 6.5
2.0 150 350
1812FS-334_L_330 10,545 6.8
3.0 150 310
1812FS-394_L_390 10,535 7.6
2.6 140 310
1812FS-474_L_470 10,535 8.7
2.1 130 280
1812FS-564_L_560 10,5 20 11.2
1.60110 280
1812FS-684_L_680 10,5 25 12.7
1.90100 250
1812FS-824_L_820 10,52516.8
1.45 90 210
1812FS-105_L_1000
10,53019.5
1.68 90 160
1. When ordering, please specify tolerance and packaging codes:
1812FS-105JLC
Tolerance: J =5% K = 10%
(Table shows stock tolerances in bold.)
Packaging:C
=7″ machine-ready reel. EIA-481 embossed plastic
tape (600 parts per full reel).
B=Less than full reel. On tape, but not machine ready.
To have a leader and a trailer added ($25 charge),
use code letter C instead.
D
=13″ machine-ready reel. EIA-481 embossed plastic
tape (2200 parts per full reel).
2. Inductance measured at 100 kHz, 0.1 Vrms, 0 Adc using a Coilcraft
SMD-A fixture in an Agilent/HP 4263B impedance analyzer.
3. Tolerances in bold are stocked for immediate shipment.
4. Q measured at 1 MHz on an Agilent/HP 4291A with an Agilent/
HP 16193 test fixture.
5. DCR measured on a micro-ohmmeter and a Coilcraft CCF840 test
fixture.
6. SRF measured using an Agilent/HP 8753D network analyzer and a
Coilcraft SMD‑D test fixture.
7. DC current at 25°C that causes an inductance drop of 10% (typ) from
its value without current. Click for temperature derating information.
8. Current that causes a 40°C temperature rise from 25°C ambient. This
information is for reference only and does not represent absolute maximum ratings. Click for temperature derating information.
9. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Document 254-1 Revised 10/12/15
Document 254-2
Filter Inductors – 1812FS Series
Typical L vs Frequency
Typical L vs Current
10000
10000
1000 µH
100 µH
100
10 µH
10
1 µH
1
0.1
1000
Inductance (µH)
Inductance (µH)
1000
0.01
0.1
100
100 µH
10
10 µH
1
1
10
Frequency (MHz)
B
overall
1000 µH
0.1
1 µH
0.01
0.1
1
10
Current (A)
0.120
3,05
C
0.045
1,14
0.118
3,00
A F
G
E
terminal
D
Recommended
Land Pattern
A max B max C max D ref E ref
F ref
G
0.231 0.1960.150 0.1070.1000.1780.025
inches
5,87 4,983,81 2,722,544,520,64
mm
Document 254-2 Revised 10/12/15