Document 106-1 Chip Inductors – 1812LS Series (4532) •Highest inductance values of all our chip inductors •Ferrite construction for high current handling •Inductance values from 12 – 1000 µH Request free evaluation samples by contacting Coilcraft or visiting www.coilcraft.com. Inductance2 SRF typ4 Percent Q Test freq DCR max5 Irms6 Part number1 (µH)tolerance min3 (MHz) (MHz) (Ohms)(mA) 1812LS-123XJL_12 5 422.5 85 2.0 310 1812LS-153XJL_15 5 422.5 70 2.5 290 1812LS-183XJL_18 5 452.5 52 2.8 270 1812LS-223XJL_22 5 452.5 58 3.2 260 1812LS-273XJL_27 5 452.5 46 3.6 240 1812LS-333XJL_33 5 452.5 40 4.0 230 1812LS-393XJL_39 5 452.5 30 4.5 210 1812LS-473XJL_47 5 422.5 24 5.0 200 1812LS-563XJL_56 5 422.5 20 5.5 190 1812LS-683XJL_68 5 402.5 16 6.0 180 1812LS-823XJL_82 5 402.5 13.5 7.0 170 1812LS-104XJL_100 5 402.5 12.0 8.0 150 1812LS-124XJL_120 5 330.7914.5 11.5 135 1812LS-154XJL_150 5 360.7911.5 13.0 125 1812LS-184XJL_180 5 360.79 9.3 14.2 120 1812LS-224XJL_220 5 380.79 7.6 16.2 115 1812LS-274XJL_270 5 380.79 8.3 20.5 105 1812LS-334XJL_330 5 380.79 7.0 22.5 100 1812LS-394XJL_390 5 380.79 5.2 24.5 90 1812LS-474XJL_470 5 380.79 4.4 26.5 85 1812LS-564XJL_560 5 330.79 2.8 28.5 75 1812LS-684XJL_680 5 330.79 2.3 38.0 60 1812LS-824XJL_820 5 300.79 2.1 41.0 55 1812LS-105XJL_1000 5 300.79 1.9 44.0 50 1. When ordering, please specify termination and packaging codes: 1812LS-105XJLC Termination:L=RoHS compliant silver-palladium-platinum-glass frit. Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or S = non-RoHS tin-lead (63/37). Packaging: C=7″ machine-ready reel. EIA-481 embossed plastic tape (600 per full reel). B =Less than full reel. In tape, but not machine-ready. To have a leader and trailer added ($25 charge), use code letter C instead. D =13″ machine-ready reel. EIA-481 embossed plastic tape. Factory order only, not stocked (2200 per full reel). 2. Inductance at 2.5 MHz measured using an Agilent/HP 4286A and a Coilcraft SMD-A fixture with Coilcraft-provided correlation pieces. Inductance at 0.79 MHz measured using an Agilent/HP 4192A and Coilcraft SMD-B test fixture. 3. Q read at test frequency directly on an Agilent/HP 4192A LF impedance analyzer and a Coilcraft SMD-B test fixture. 4. SRF measured using an Agilent/HP 8753D network analyzer and a Coilcraft SMD-D test fixture. 5. DCR measured on a Cambridge Technology micro-ohmmeter. 6. Current that causes a 15°C temperature rise from 25°C ambient. This information is for reference only and does not represent absolute maximum ratings. 7. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. Visit http://www.coilcraft.com/colrcode.cfm for part marking data. Document 106-1 Revised 10/12/15 Document 106-2 1812LS (4532) Chip Inductors Typical Q vs Frequency Typical L vs Current 10000 60 50 12 µH Q Factor 40 82 µH 18 µH 33 µH Inductance (µH) 270 µH 560 µH 1000 µH 30 20 1000 µH 1000 330 µH 100 µH 100 33 µH 2.5 MHz 10 0.79 MHz 12 µH 10 0 0.1 0.2 0.3 0.4 D F E terminal 1 Frequency (MHz) 2 3 C B overall A 0.6 4 5 6 8 10 H Pick and place material I G J F I Terminal wraparound: approx 0.015/0,38 both ends Recommended Land Pattern ABCD maxmaxmax ref E F G H IJ 0.1950.1500.1350.0700.1000.0250.1280.1200.0450.118inches 4,953,813,431,782,540,643,253,051,143,00 mm Note: Height dimension (C) is before optional solder application. For maximum height dimension including solder, add 0.006 in / 0,152 mm. 1 10 100 DC Current (mA) 1000 Designer’s Kit C314 contains 10 of each value Core material Ferrite Terminations RoHS compliant silver-palladium-platinum-glass frit. Other terminations available at additional cost. Weight 142 – 171 mg Ambient temperature –40°C to +85°C with Irms current Maximum part temperature +100°C (ambient + temp rise) Storage temperature Component: –40°C to +100°C. Tape and reel packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Temperature Coefficient of Inductance (TCL) +200 to +700 ppm/°C Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) One per billion hours / one billion hours, calculated per Telcordia SR-332 Packaging 600/7″ reel; 2200/13″ reel. Plastic tape: 12 mm wide, 0.3 mm thick, 8 mm pocket spacing, 3.7 mm pocket depth PCB washing Tested to MIL-STD-202 Method 215 plus an additional aqueous wash. See Doc787_PCB_Washing.pdf. Document 106-2 Revised 10/12/15