DO5022P

Document 172-1
SMT Power Inductors – DO5022P
• Excellent current handling – up to 28.8 Asat.
• Low dc resistance keeps power losses to a minimum
Designer’s Kit C311 contains 3 of each 20% tolerance part
Core material Ferrite
Core and winding loss See www.coilcraft.com/coreloss
Terminations RoHS compliant electroplated gold (<50 µin) over nickel
over phos bronze. Other terminations available at additional cost.
Weight 2.8 – 3.9 g
Ambient temperature –40°C to +85°C with Irms current, +85°C to
+125°C with derated current
Storage temperature Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 250 per 13″ reel Plastic tape: 32 mm wide,
0.38 mm thick, 24 mm pocket spacing, 7.8 mm pocket depth
PCB washing Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
Isat (A)5
DCR SRF L2 Percentmax typ4 10%20% Irms6
Part number1(µH) tol3 (Ohms)(MHz) dropdrop (A)
DO5022P-102ML_1.0
20 0.009
DO5022P-222ML_2.2
20 0.014
DO5022P-332ML_3.3
20 0.018
DO5022P-562ML_5.6
20 0.020
DO5022P-822ML_8.2
20 0.029
DO5022P-103ML_1020 0.031
DO5022P-153ML_1520 0.036
DO5022P-223ML_2220 0.047
DO5022P-333ML_3320 0.066
DO5022P-473ML_4720 0.086
DO5022P-683_L_6820,100.13
DO5022P-104_L_100 20,100.19
DO5022P-154_L_150 20,100.25
DO5022P-224_L_220 20,100.38
DO5022P-334_L_330 20,100.56
DO5022P-474_L_470 20,100.85
DO5022P-684_L_680 20,101.1
DO5022P-105_L_1000 20,101.8
80 27.628.88.6
80 18.519.87.1
60 14.515.56.2
40 12.513.85.3
30 10.311.54.8
30 9.410.54.3
22 7.5 8.24.0
20 6.5 7.23.5
15 5.2 6.13.0
9 4.2 4.72.6
8
3.7 4.1 2.3
7
3.0 3.4 1.8
6
2.5 2.8 1.5
5
2.0 2.3 1.2
4
1.7 1.9 1.0
3
1.5 1.7 0.82
2.5 1.2 1.3 0.72
2.0 0.95 1.1 0.56
1.Specify tolerance, termination and packaging codes:
DO5022P-105MLD
Tolerance:
M= 20%, K = 10% (Table shows stock
tolerances in bold.)
Termination:L =RoHS compliant gold over nickel over
phos bronze.
Special order:
T = RoHS tin-silver-copper (95.5/4/0.5)
or S = non-RoHS tin-lead (63/37).
Packaging:D
=13″ machine-ready reel. EIA-481
embossed plastic tape (250 parts per
full reel).
B=Less than full reel. In tape, but not
machine ready.
To have a leader and trailer added
($25 charge), use code letter D
instead.
2. Inductance tested at 100 kHz, 0.1 Vrms, 0 Adc using an
Agilent/HP 4263B LCR meter or equivalent.
3. Tolerances in bold are stocked for immediate shipment.
4. SRF >13 MHz measured using Agilent/HP 8753D
network analyzer; <13 MHz using Agilent/HP 4192A.
5. DC current at which inductance drops the specified
amount from its value without current.
6. Current that causes a 40°C temperature rise from 25°C
ambient.
7. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components”
before soldering.
Document 172-1 Revised 12/09/11
Document 172-2
SMT Power Inductors – DO5022P Series
Typical L vs Current
Typical L vs Frequency
10000
10000
1000 µH
100 µH
100
10 µH
10
1 µH
1
0.1
0.1
1000 µH
1000
Inductance (µH)
Inductance (µH)
1000
100 µH
100
10 µH
10
1 µH
1
100
10
1
Current (A)
0.1
0.01
Current Derating
1
0.1
0.710 ±0.020 *
18,03 ±0,508
an additional 0.01/0,254
* Allow
in length and 0.005/0,127 in
height for optional tin-lead and
tin-silver-copper application.
120
110
0.600
max
15,24
100
90
80
0.500
dia
12,70
70
60
0.280
max*
7,11
50
40
25°C
Percent of rated Irms
10
Frequency (MHz)
30
0.100
2,54
0.100
2,54
20
0.605
15,37
0.110
2,79
10
0
-40
-20
0
20
40
60
80
100
0.115
2,92
120 140
Ambient temperature (°C)
Recommended
Land Pattern
0.510 ±0.010
12,95 ±0,25
Internal code
XXX
X
Start
Dash number
Finish
Part Marking
Dimensions are in
inches
mm
Document 172-2 Revised 12/09/11