DT1608C

Document 178-1
Shielded Power Inductors – DT1608C
• Low temperature rise allows use at up to 150% of rated current.
• “Swinging” inductance allows use as high L inductors.
Core material Ferrite
Ambient temperature –40°C to +85°C
Storage temperature Component: –40°C to +85°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Three reflows at >217°C for 90 seconds (+260°C ±5°C for 20 – 40 seconds), allowing parts to cool to
room temperature between.
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
PCB washing Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
Coilcraft will continue to manufacture and support the
DT1608C indefinitely. For new designs, consider the
LPS4018 as an alternative to this series. The LPS4018
series is more cost effective, features a smaller footprint, lower profile and better current handling.
Specifications
Inductance2
DCR max
SRF typ
Part number1
±20% (µH)
(Ohms)
(MHz)
DT1608C-102ML_
1.0
0.065
180
DT1608C-152ML_
1.5
0.070
120
DT1608C-222ML_
2.2
0.075
100
DT1608C-332ML_
3.3
0.080
70
DT1608C-472ML_
4.7
0.085
60
DT1608C-682ML_
6.8
0.090
50
DT1608C-103ML_
10
0.125
45
DT1608C-153ML_
15
0.135
35
DT1608C-223ML_
22
0.160
25
DT1608C-333ML_
33
0.275
20
DT1608C-473ML_
47
0.300
17
DT1608C-683ML_
68
0.575
14
DT1608C-104ML_
100
1.10
12
DT1608C-154ML_
150
1.40
7.0
DT1608C-224ML_
220
2.25
7.0
DT1608C-334ML_
330
2.90
6.0
DT1608C-474ML_
470
3.60
4.0
DT1608C-684ML_
680
4.55
3.5
DT1608C-105ML_
1000
8.10
2.5
1. When ordering, please specify termination and packaging codes:
DT1608C-106MLC
Termination:L=RoHS compliant electroplated gold (<50 µin) over
nickel over moly-manganese.
Special order: T = RoHS tin-silver-copper (95.5/4/0.5)
or S = non-RoHS tin-lead (63/37).
Packaging:C
=7″ machine-ready reel. EIA-481 embossed plastic
tape (750 parts per full reel).
B=Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge), use
code letter C instead.
D
=13″ machine-ready reel. EIA-481 embossed plastic
tape (2500 parts per full reel).
Operating Parameters
Inductance Current EnergySwitching
rating3
rating4
storage max frequency
(µH)
(A)
(µJoules)
max
0.60
2.0
1.8
1 MHz
0.80
1.9
1.8
1 MHz
0.90
1.5
1.8
1 MHz
1.5
1.2
1.4
1 MHz
2.0
1.2
1.6
1 MHz
3.0
1.0
1.9
1 MHz
5.0
0.7
1.2
1 MHz
6.0
0.6
1.1
1 MHz
10
0.5
1.2
1 MHz
12
0.45
1.5
1 MHz
20
0.34
1.3
1 MHz
30
0.29
1.4
1 MHz
40
0.24
1.5
1 MHz
60
0.20
1.4
500 kHz
90
0.17
1.6
500 kHz
100
0.16
1.4
500 kHz
150
0.14
1.5
500 kHz
200
0.12
1.4
500 kHz
400
0.08
1.4
500 kHz
2. Inductance tested at 0.1 Vrms, 100 kHz, 0 Adc.
3. Measured at the rated current. Refer to L vs Current curves for details.
4. Average maximum allowable current. DT Series inductors are designed
for current spikes as high as twice the current rating.
5. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Document 178-1 Revised 05/20/10
Document 178-2
Shielded Power Inductors – DT1608C Series
Typical L vs Current
Dash number
XXX
10000
Inductance (µH)
1000
-105
0.160
dia
4,06
0.115max
2,92
-104
100
0.260 max
6,60
-103
10
0.070
1,78
0.175max
4,45
-102
1
0.1
0.1
Current (A)
1
10
Isat Derating
0.160
4,06
0.140
3,56
0.090
2,29
0.170min
4,32
0.01
0.055
1,40
0.050
1,27
Dimensions are in
inches
mm
0.040
1,02
0.270
6,86
Recommended
Land Pattern
Weight: 136 – 157 mg
Tape and reel: 750/7″ reel; 2500/13″ reel 12 mm tape wide,
0.28 mm thick, 8 mm pocket spacing, 3.0 mm pocket depth.
+20
+10
0
-10
25°C
Change in rated current (%)
+30
-20
-30
-40
-20
0
20
40
60
80
100
120 140
Ambient temperature (°C)
Document 178-2 Revised 05/20/10