Document 208-1 SMT Power Inductors - LPO2506 • On-board style – 1.65 mm high • InBoard® style – only 1.19 high Designer’s Kit C332 contains 3 of all InBoard® styles Designer’s Kit C333 contains 3 of all On-board styles Core material Ferrite Core and winding loss See www.coilcraft.com/coreloss Terminations RoHS compliant silver-palladium-platinum-glass frit. Other terminations available at additional cost. Weight 240 – 260 mg Ambient temperature –40°C to +85°C with Irms current, +85°C to +125°C with derated current Storage temperature Component: –40°C to +125°C. Tape and reel packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332 Packaging 1000/13″ reel Plastic tape: 12 mm wide, 0.23 mm thick, 8 mm pocket spacing, 1.37 mm pocket depth PCB washing Tested to MIL-STD-202 Method 215 plus an additional aqueous wash. See Doc787_PCB_Washing.pdf. L ±20%2 Isat3 Irms4 InBoard style On-board style DCR max SRF typ part number1 part number1 (µH) (Ohms) (MHz) (A) (A) LPO2506I-472L_LPO2506O-472L_ 4.7 0.145 90 1.6 1.9 LPO2506I-682L_LPO2506O-682L_ 6.8 0.165 75 1.3 1.7 LPO2506I-822L_LPO2506O-822L_ 8.2 0.200 65 1.0 1.5 LPO2506I-103L_LPO2506O-103L_ 10 0.240 60 1.0 1.5 LPO2506I-153L_LPO2506O-153L_ 15 0.300 45 0.90 1.3 LPO2506I-223L_LPO2506O-223L_ 22 0.420 35 0.70 1.0 LPO2506I-333L_LPO2506O-333L_ 33 0.550 30 0.60 0.90 LPO2506I-473L_LPO2506O-473L_ 47 0.765 22 0.50 0.70 LPO2506I-683L_LPO2506O-683L_ 68 1.10 20 0.40 0.60 LPO2506I-104L_LPO2506O-104L_ 100 1.60 15 0.30 0.50 LPO2506I-154L_LPO2506O-154L_ 150 2.50 12 0.25 0.40 LPO2506I-224L_LPO2506O-224L_ 220 3.65 10 0.22 0.32 LPO2506I-334L_LPO2506O-334L_ 330 4.65 8.0 0.18 0.28 LPO2506I-474L_LPO2506O-474L_ 470 6.75 6.5 0.14 0.24 LPO2506I-684L_LPO2506O-684L_ 680 9.15 5.5 0.12 0.20 LPO2506I-105L_LPO2506O-105L_ 1000 14.20 4.5 0.10 0.16 1. When ordering, please specify termination and packaging codes: LPO2506O-105LD Termination: L = RoHS compliant silver-palladium-platinum-glass frit Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or S = non-RoHS tin-lead (63/37). Packaging:D =13″ machine-ready reel. EIA-481 embossed plastic tape (1000 parts per full reel). B=Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter D instead. 2. Inductance tested at 100 kHz, 0.1 Vrms, 0 Adc using an Agilent/HP 4263B LCR meter or equivalent. 3. DC current at which the inductance drops 10% (typ) from its value without current. 4. Current that causes a 40°C temperature rise from 25°C ambient. 5. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. Document 208-1 Revised 02/25/15 Document 208-2 SMT Power Inductors - LPO2506 Series Typical L vs Frequency Typical L vs Current 1000 µH 100 µH 100 10 µH 10 0.01 0.1 1 10 On-board Style 10 µH 1 0.01 0.1 Current (A) 1 XXXY 0.190 4,83 0.190 4,83 0.205 5,21 0.254 max 6,45 Mounting plane: through board 0.030 0,76 0.048 1,21 0.285 7,24 0.380 max 9,65 0.065 max 1,65 0.061max 1,55 0.360 max 9,14 0.285 max 7,24 Note: Parts manufactured prior to March, 2011 were marked only with the dash number 0.230 5,84 0.254 max 6,45 0.030 0,76 Recommended Land Pattern Dash number 0.205 5,21 InBoard Style 0.310 max 7,87 10 Internal code 0.360 max 9,14 0.285 max 7,24 100 µH 100 10 Frequency (MHz) 0.310 max 7,87 1000 µH 1000 Inductance (µH) Inductance (µH) 1000 1 Current Derating 10000 10000 0.047 max 1,19 Recommended Land Pattern 0.048 1,21 0.285 7,24 0.230 5,84 ∅0.284 ∅7,21 hole through board 0.380 max 9,65 Document 208-2 Revised 02/25/15