Document 349-1 Shielded Power Inductor – SER2000 • Designed for high current power supply applications • Flat wire windings provide exceptionally low DCR • Isat ratings as high as 100 A Designer’s Kit C374 contains 2 each of nine parts. Core material Ferrite Core and winding loss See www.coilcraft.com/coreloss Terminations RoHS compliant tin-silver over copper. Other terminations available at additional cost. Ambient temperature –40°C to +85°C with (40°C rise) Irms current. Maximum part temperature +125°C (ambient + temp rise). Derating. Storage temperature Component: –40°C to +125°C. Tape and reel packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332 PCB washing Tested to MIL-STD-202 Method 215 plus an additional aqueous wash. See Doc787_PCB_Washing.pdf. Recommended Land Pattern 0.755 ±0.02 19,18 ±0,51 0.160 4,06 0.736 ±0.034 18,70 ±0,86 SER20xx-xxxL XXXX Y CL 0.365 ±0.02 9,27 ±0,51 2 3 3 0.470 11,94 CL 0.412 ±0.034 10,46 ±0,86 0.015 0,38 Internal code 1 0.100 ±0.003 typ 2,54 ±0,076 0.311 ±0.015 7,90 ±0,38 0.150 3,81 0.185 4,70 2 0.260 6,60 0.210 5,33 0.130* 3,30 inches mm *Width of flat area on winding Maximum height SER2009 SER2010 SER2011 SER2012 SER2013 SER2014 Packaging SER2009 200 per 13″ reel; Plastic tape: 44 mm SER2010 200 per 13″ reel; Plastic tape: 44 mm SER2011 170 per 13″ reel; Plastic tape: 44 mm SER2012 150 per 13″ reel; Plastic tape: 44 mm SER2013 150 per 13″ reel; Plastic tape: 44 mm SER2014 125 per 13″ reel; Plastic tape: 44 mm 0.004/0,102 0.125 3,18 Caution: Terminal 3 is provided for mounting stability only. This terminal is connected to the winding of the inductor and must not be connected to ground or any circuitry. 0.150 3,81 Height (See table) Dimensions are in 1 0.290 7,37 0.515±0.015 13,08 ±0,37 0.34 / 8,64 0.37 / 9,40 0.42 / 10,67 0.47 / 11,94 0.51 / 12,95 0.55 / 13,97 Weight 6.65 – 6.89 g 7.46 – 7.90 g 8.63 – 9.08 g 9.92 – 10.3 g 10.8 – 11.4 g 11.7 – 12.4 g 0.100 2,54 wide, 0.4 mm thick, 32 mm pocket spacing, 9.25 pocket depth wide, 0.4 mm thick, 32 mm pocket spacing, 10.5 pocket depth wide, 0.4 mm thick, 32 mm pocket spacing, 11.6 pocket depth wide, 0.4 mm thick, 32 mm pocket spacing, 13.0 pocket depth wide, 0.5 mm thick, 32 mm pocket spacing, 14.0 pocket depth wide, 0.5 mm thick, 32 mm pocket spacing, 15.0 pocket depth Document 349-1 Revised 09/05/12 Document 349-2 Shielded Power Inductors – SER2000 Series 1. Please specify termination and packaging codes: SER2014-202MLD Termination:L =RoHS compliant tin-silver over copper. Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or S = non-RoHS tin-lead (63/37). Packaging:D =13″ machine-ready reel. EIA-481 embossed plastic tape. B=Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter D instead. 2. Inductance measured at 100 kHz, 0.1 Vrms, 0 Adc on an Agilent/HP 4263B LCR meter or equivalent. 3. DCR measured on a Keithley 580 micro-ohmmeter. 4. SRF measured using an Agilent/HP 4395A network analyzer and an Agilent/HP 16092A test fixture. 5. DC current at 25°C that causes a 10% (typ) inductance drop from its value without current. Click for temperature derating information. 6. Current that causes the specified temperature rise from 25°C ambient. This information is for reference only and does not represent absolute maximum ratings. Click for temperature derating information. When Irms is greater than Isat, Isat is the more critical specification, and Irms is shown in gray type. See Temperature Rise vs Current curve below. 7. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. Temperature Rise vs Current 70 60 SE R2 014 SE R2 013 SE R2 012 SE R2 01 1 SE R2 01 0 SE R2 00 9 6 Temperature rise (from 25°C) Irms (A) Inductance DCR DCR SRF ±20%2 typ3 max3typ4 Isat5 20°C40°C Height Part number1 (µH)(m)(m)(MHz) (A) rise rise (mm) SER2009-301ML_0.30 0.6300.740 550 100 41 54 8,64 SER2010-301ML_0.30 0.900 1.00 182 100 36 45 9,40 SER2009-501ML_0.50 0.6300.740 544 60 41 54 8,64 SER2010-501ML_0.50 0.9001.00 148 81 36 45 9,40 SER2011-501ML_0.50 1.20 1.34 161 100 30 40 10,67 SER2009-601ML_0.60 0.6300.740 648 49 41 548,64 SER2010-601ML_0.60 0.900 1.00 115 70 36 459,40 SER2011-601ML_0.60 1.20 1.34 124 90 30 40 10,67 SER2012-601ML_0.60 1.44 1.60 115 97 25 35 11,94 SER2009-681ML_0.68 0.6300.740 454 45 41 548,64 SER2010-681ML_0.68 0.9001.00 136 62 36 45 9,40 SER2011-681ML_0.68 1.20 1.34 135 78 30 40 10,67 SER2012-681ML_0.68 1.44 1.60 103 85 25 35 11,94 SER2013-681ML_0.68 1.70 1.82 104 98 23 30 12,95 SER2009-801ML_0.80 0.6300.740 567 38 41 548,64 SER2010-801ML_0.80 0.900 1.00 92 53 36 45 9,40 SER2011-801ML_0.80 1.20 1.34 113 70 30 40 10,67 SER2012-801ML_0.80 1.44 1.60 91 75 25 35 11,94 SER2013-801ML_0.80 1.70 1.82 93 85 23 30 12,95 SER2014-801ML_ 0.80 1.94 2.15 104 98 21 27 13,97 SER2009-901ML_0.90 0.6300.740 557 33 41 548,64 SER2010-901ML_0.90 0.9001.00 96 48 36 45 9,40 SER2011-901ML_0.90 1.20 1.34 104 62 30 40 10,67 SER2012-901ML_0.90 1.44 1.60 85 69 25 35 11,94 SER2013-901ML_0.90 1.70 1.82 98 73 23 30 12,95 SER2014-901ML_0.90 1.94 2.15 102 87 21 27 13,97 SER2009-102ML_1.0 0.6300.740 488 29 41 548,64 SER2010-102ML_1.0 0.900 1.00 81 42 36 459,40 SER2011-102ML_1.0 1.20 1.34 97 56 30 40 10,67 SER2012-102ML_1.0 1.44 1.60 75 64 25 35 11,94 SER2013-102ML_1.0 1.70 1.82 98 68 23 30 12,95 SER2014-102ML_1.0 1.94 2.15 88 70 21 272713,97 SER2009-122ML_1.2 0.6300.740 81 28 41 548,64 SER2010-122ML_1.2 0.9001.00 69 37 36 459,40 SER2011-122ML_1.2 1.20 1.34 81 49 30 40 10,67 SER2012-122ML_1.2 1.44 1.60 73 54 25 35 11,94 SER2013-122ML_ 1.2 1.70 1.82 82 58 23 30 12,95 SER2014-122ML_1.2 1.94 2.15 78 63 21 27 13,97 SER2009-202ML_2.0 0.6300.740 40 16 41548,64 SER2010-202ML_2.0 0.900 1.00 48 27 36459,40 SER2011-202ML_2.0 1.20 1.34 56 37 30 4010,67 SER2012-202ML_2.0 1.44 1.60 51 35 25 35 11,94 SER2013-202ML_2.0 1.70 1.82 61 40 23 30 12,95 SER2014-202ML_2.0 1.94 2.15 62 45 21 27 13,97 SER2013-362ML_3.6 1.70 1.82 38 25 23 3012,95 SER2013-402ML_4.0 1.70 1.82 35 20 233012,95 SER2014-402ML_4.0 1.94 2.15 36 25 21 2713,97 SER2013-472ML_4.7 1.70 1.82 30 18 233012,95 50 40 30 20 10 0 0 10 20 30 40 50 60 70 Current (A rms) Parts shown in bold are included in Coilcraft Designer’s Kit C374. Document 349-2 Revised 09/05/12 Document 349-3 Shielded Power Inductors – SER2000 Series 10.0 8.0 6.0 10.0 8.0 6.0 4.0 4.0 2.0 2.0 µH 1.0 0.8 1.2 µH 1.0 µH 0.9 µH 0.8 µH 0.68 µH 0.6 µH 0.5 µH 0.6 0.4 Inductance (µH) Inductance (µH) L vs Frequency 2.0 µH 2.0 1.2 µH 1.0 µH 0.9 µH 0.8 µH 0.68 µH 0.6 µH 1.0 0.8 0.6 0.4 0.3 µH 0.2 0.1 0.2 SER2009 0.1 1 10 0.1 100 SER2012 0.1 1 10 100 Frequency (MHz) 10.0 8.0 6.0 10.0 8.0 6.0 4.7 µH 4.0 4.0 3.6 µH 2.0 2.0 µH 1.0 0.8 1.2 µH 1.0 µH 0.9 µH 0.8 µH 0.68 µH Inductance (µH) Inductance (µH) Frequency (MHz) 2.0 µH 2.0 1.2 µH 1.0 µH 0.9 µH 0.8 µH 0.68 µH 0.6 µH 0.5 µH 1.0 0.8 0.6 0.4 0.6 0.4 0.3 µH 0.2 0.1 0.2 SER2010 0.1 1 10 0.1 100 SER2013 0.1 1 10 100 Frequency (MHz) 10.0 8.0 6.0 10.0 8.0 6.0 4.0 4.0 4.0 µH 2.0 2.0 µH Inductance (µH) Inductance (µH) Frequency (MHz) 2.0 µH 2.0 1.2 µH 1.0 µH 0.9 µH 0.8 µH 0.68 µH 0.6 µH 0.5 µH 1.0 0.8 0.6 0.4 0.2 0.1 1.2 µH 1.0 µH 0.9 µH 0.8 µH 1.0 0.8 0.6 0.4 0.2 SER2011 0.1 1 10 Frequency (MHz) 100 0.1 SER2014 0.1 1 10 100 Frequency (MHz) Document 349-2 Revised 09/05/12 Document 349-4 Shielded Power Inductors – SER2000 Series 10.0 8.0 6.0 10.0 8.0 6.0 4.0 4.0 2.0 µH 2.0 Inductance (µH) Inductance (µH) L vs Current 1.2 µH 1.0 0.8 0.6 0.4 0.2 0.1 1.0 µH 0.90 µH 0.80 µH 0.68 µH 0.60 µH 0.50 µH 0.30 µH SER2009 0.1 10 1 2.0 µH 2.0 1.2 µH 1.0 0.8 0.6 1.0 µH 0.4 0.1 100 4.0 4.0 2.0 µH Inductance (µH) Inductance (µH) 10.0 8.0 6.0 1.2 µH 1.0 0.8 0.6 0.4 0.1 1.0 µH 0.90 µH 0.80 µH 0.68 µH 0.60 µH 0.50 µH 0.30 µH SER2010 0.1 10 1 10 1 3.6 µH 2.0 µH 1.2 µH 1.0 0.8 0.6 1.0 µH 0.4 0.1 100 2.0 µH Inductance (µH) Inductance (µH) 4.0 1.2 µH 1.0 0.8 0.6 0.2 0.1 0.68 µH 0.60 µH 10 1 Current (A) 0.68 µH SER2013 0.1 10 1 100 4.0 µH 2.0 µH 2.0 1.2 µH 1.0 0.8 0.6 1.0 µH 0.4 0.90 µH 0.80 µH 0.2 0.50 µH SER2011 0.1 0.80 µH Current (A) 4.0 0.80 µH 0.90 µH 0.2 10.0 8.0 6.0 1.0 µH 0.90 µH 100 4.7 µH 2.0 10.0 8.0 6.0 0.4 0.60 µH SER2012 0.1 Current (A) 2.0 0.68 µH Current (A) 10.0 8.0 6.0 0.2 0.80 µH 0.2 Current (A) 2.0 0.90 µH 100 0.1 SER2014 0.1 10 1 100 Current (A) Document 349-2 Revised 09/05/12