Model 132 www.vishay.com Vishay Spectrol 1 5/16" (33.3 mm) Low Cost Industrial Single Turn Wirewound, Bushing Mount Type Potentiometer FEATURES • Suitable model for all industrial applications • Center tap available • Continuous rotation and mechanical stops both standard • Large electrical angle: 352° ± 2° • Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 QUICK REFERENCE DATA Sensor type Output type Market appliance Dimensions ROTATIONAL, single turn wirewound Output by turrets Industrial 1 5/16" (33.3 mm) ELECTRICAL SPECIFICATIONS PARAMETER MIL-PRF-12934 TEST PROCEDURES APPLY STANDARD SPECIAL 5 to 20 k to 35 k ±3% ±1% ±5% ±3% STANDARD BEST PRACTICAL Total Resistance Tolerance: 50 and Above Below 50 Linearity (independent) Total Resistance 5 to 20 20 to 200 200 and above Noise Power Rating ± 1.0 % ± 1.0 % ± 0.5 % ± 0.75 % ± 0.50 % ± 0.25 % 100 ENR 40 °C ambient 2.75 W derated to zero at 125 °C Electrical Angle Continuous Rotation Stops Insulation Resistance Dielectric Strength Absolute Minimum Resistance Minimum Voltage Temperature Coefficient of Resistance 352° ± 2° 340° ± 5° 1000 M minimum at 500 VDC 1000 VRMS, 60 Hz 1.0 % of total resistance or 0.5 W whichever is greater 0.5 % maximum Refer to standard resistance element data MATERIAL SPECIFICATIONS ENVIRONMENTAL SPECIFICATIONS Housing Rear Lid Shaft Vibration Shock Salt Spray Rotational Life Shaft Revolutions Operating Temperature Range Terminals Mount Hardware Lockwasher Internal Tooth: Panel Nut: Molded glass filled thermoplastic Glass filled thermoset plastic Stainless steel, non-magnetic Brass, plated for solderability, Non-passivated Steel, nickel plated Brass, nickel plated 15 g thru 2000 Hz 50 g 48 h 500 000 - 55 °C to + 125 °C ORDERING INFORMATION/DESCRIPTION 132 0 20K BO10 OTHER OPTIONAL MODEL OHMIC VALUE PACKAGING FEATURES 0. Standard (end taps) 0. Continuous 1. Center tap (within Box of 10 pieces 2. Stops 5° of electrical center) Other characteristics will be standard as described on this specification sheet. If special characteristics are required such as special linearity tolerance, special resistance tolerance, non-linear functions, etc., please state these on your order. Revision: 12-Apr-13 B BUSHING MOUNT 0 MECHANICAL OPTIONS Document Number: 57096 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Model 132 www.vishay.com Vishay Spectrol SAP PART NUMBERING GUIDELINES 132 MODEL B STYLE 2 MECHANICAL OPTIONS 2: With stops 1 ELECTRICAL OPTIONS 1: With center tap 103 OHMIC VALUE B10 PACKAGING 103: 10K Box of 10 pieces DIMENSIONS in inches (millimeters) ± 0.031 MODEL 132B/132-... ± 0.015 60° Ø 0.500 (12.70) BC 0.187 (4.75) ± 0.015 ± 0.015 0.625 (15.88) 0.875 (22.22) + 0.0000 Ø 0.4062 - 0.0020 MTG. (10.32) ± 0.015 0.375 (9.52) ± 0.010 0.032 (0.81) 0.062 (1.57) + 0.0000 Ø 0.2497 (6.34) - 0.0003 0.030 MAX. (0.76) 0.562 (14.27) ± 0.015 Ø 1.312 (33.32) 0.032 (0.81) 3/ 8 - 32 UNEF - 2A Ø 0.125 (3.18) 2 0.062 (1.57) TOLERANCES: UNLESS OTHERWISE NOTED. DECIMALS ± 0.005 ANGLES ± 2° CW 3 1 MTG. SURFACE SCHEMATIC MECHANICAL SPECIFICATIONS PARAMETER Rotation Bearing Type 360° (continuous) or 340° ± 5° (stops) Sleeve STARTING RUNNING 1.0 oz. - in (72 g - cm) 0.7 oz.- in (50.40 g - cm) Torque (maximums) Runouts (maximums) Shaft Runout (TIR) Pilot Dia. Runout (TIR) Lateral Runout (TIR) Shaft End Play Shaft Radial Play Weight Stop Strength 0.002" (0.05 mm) 0.003" (0.08 mm) 0.005" (0.13 mm) 0.008" (0.20 mm) 0.003" (0.08 mm) 1.0 oz. maximum (28.35 g) 8.0 in - lbs (9.21 kg - cm) (stops version only) POWER RATING CHART RESISTANCE ELEMENT DATA RATED POWER IN W 6.0 RESISTANCE RESO- OHMS VALUES LUTION PER () TURN (%) 5.0 4.0 3.0 2.0 1.0 0 20 40 60 80 100 120 140 AMBIENT TEMPERATURE IN °C MARKING Unit Identification Units shall be marked with Vishay Spectrol name, model number, resistance and tolerance, linearity, terminal identification, and data code Applicable test procedures: MIL-R-12934. Example of a marking for a standard part: 132-0-0-103 Revision: 12-Apr-13 5 10 20 50 100 200 500 1K 2K 5K 10K 20K 35K 0.419 0.327 0.280 0.290 0.251 0.212 0.161 0.150 0.132 0.107 0.080 0.067 0.057 0.021 0.032 0.056 0.145 0.251 0.424 0.806 1.50 2.64 5.34 7.98 13.4 20.0 MAXIMUM CURRENT AT 40 °C AMBIENT (mA) 742 524 371 234 166 122 74.2 52.4 37.1 23.4 16.6 12.2 8.88 MAXIMUM WIRE VOLTAGE TEMP. ACROSS COEF. COIL (ppm/°C) (V) 3.71 800 5.24 800 7.42 800 11.7 20 16.6 20 24.4 20 37.1 20 52.4 20 74.2 20 117 20 166 20 244 20 311 20 Document Number: 57096 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000