Description Purpose and application The EASY RC radio receiver is used to receive wireless radio signals from EASY hybrid remote hand-held transmitters or EASY Color Drive wall operating units and transmit these to EASY control units. EASY RC The radio receiver can be installed in luminaires or, with the optional ECO CI KIT, in suspended ceilings. Function The radio receiver converts the radio signals of the hand-held transmitters and wall operating units into the corresponding telegrams and transmits them through wires to the connected EASY control units. The radio receiver is supplied directly from the EASY signal line and can be connected anywhere in the EASY signal line. Construction A B The radio receiver is made up of the following components: • LED (A) • Connections for EASY signal: Radio receiver Fitting instructions –– Modular 4p4c socket (B) –– 4-pin plug-in terminal (C) • „Connect“ button for training and untraining hand-held transmitters/wall operating units (D) D C Installation Safety instructions The radio receiver must only be installed and put into operation by a qualified electrician. The applicable safety regulations and German accident prevention regulations must be observed. CAUTION! Destruction of the radio receiver and other devices due to incorrect installation! • Adhere to the connection diagram. • Do not wire the plug-in terminals with an external voltage, especially not a mains voltage of 230 V. • Do not install the radio receiver close to sources of radio interference. • Ensure that there is a sufficient distance to ECGoperated lamps, the corresponding mains and lamp lines and shielding metal parts. EASY RC EASY Signal E 1 2 3 4 L N DALI EASY III Easy Signal L N Y-Connector F 24 V (+) CH1 (R-) EASY Signal 1 2 3 4 1 2 3 4 Connecting the radio receiver EConnection via supplied modular 4p4c cable F Connection via 4-pin cable L N DALI EASY III Easy Signal Y-Connector EASY-RC_ma0908en_we1.01.indd CH4 (W-) GND (-) Y-Connector Scew EASY RC • The radio receiver is designed for installation in luminaires and devices. It can only be installed separately (e.g. in suspended ceilings) by using the ECO CI KIT available as an accessory. (G-) OT EASY 60 II CH2 CH3 (B-) Easy signal VIII 2009 GND (-) CH4+ (W) CH3+ (B) CH2+ (G) CH1+ (R) L N GND (-) CH4+ (W) CH3+ (B) CH2+ (G) CH1+ (R) 24 V (+) CH1 (R-) (G-) OT EASY 60 II CH2 CH3 (B-) Easy signal CH4 (W-) GND (-) OSRAM GmbH Kunden Service Center Customer-Service-Center (CSC) Steinerne Furt 62 86167 Augsburg Germany Tel : +49 (0) 1803 677 - 200 (kostenpflichtig / charges apply) Fax.: +49 (0) 1803 677 - 202 www.osram.com www.osram.de EAN: 4008321421753 Page 1 of 2 Appendix Technical data Operating temperature 0 °C ... +50 °C Transmission power 10 mW Radio signal Frequency band 868.3 MHz FSK digital signal (OSRAMspecific coding) Functional range In the open air: approx. 100 m In buildings: approx. 30 m Permissible conductor crosssection when connected via terminals Single-wire conductor (AWG 26 – AWG 20): 0.13 - 0.5 mm² Fine-wire conductor (AWG 24 – AWG 20): 0.2 - 0.5 mm² Maximum number of handheld transmitters/wall operating units 8 Protection class III Protection type IP 20 Dimensions (L x W x H) 118 x 30 x 21 mm Accessories Note: The accessories are not included. Designation Description Product number Y-CONNECTOR 4050300803135 Y-connector for EASY signal connection with modular 4p4c cable Y-CONNECTOR screw Y-connector with screw terminals for EASY signal connection with 4-pin cable 4008321916686 ECO CI KIT Strain relief for the separate installation of the EASY RC receiver (e.g. ceiling installation) 4008321392091 Disposal Do not dispose of the device with household waste. Electronic devices must be disposed of at local recycling centres for waste electronic equipment in accordance with EU Directive 2002/96/EC on waste electrical and electronic equipment. Conformity with the relevant EU directives is confirmed by the CE symbol. Page 2 of 2