Model 533, 534, 535 www.vishay.com 7/ 8" Vishay Spectrol (22.2 mm) Multi Turn Wirewound Potentiometer 533: 3 Turns / 534: 10 Turns / 535: 5 Turns FEATURES • • • • • • • • QUICK REFERENCE DATA Sensor type Output type Market appliance Dimensions ROTATIONAL, multi turn wirewound Output by turrets Industrial 7/ " (22.2 mm) 8 Bushing and servo mount designs available Special resistance tolerances to 1 % Rear shaft extensions and support bearing Metric shaft available Dual gang configuration and concentric shafts High torque, center tap, slipping clutch on request Special markings and front shaft extensions Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 ELECTRICAL SPECIFICATIONS PARAMETER Resistance range - standard values Capability range Standard tolerance Linearity (independent) Noise MODEL 533 50 to 20 k 5 to 60 k ±5% ± 0.25 % 100 ENR 1080° +10° Rotation (electrical and mechanical) MODEL 534 100 to 100 k 10 to 200 k ±5% ± 0.25 % 100 ENR 3600° +10° -0° Power rating (at 70 °C) Insulation resistance Dielectric strength Absolute minimum resistance Temperature coefficient End voltage Phasing Taps MODEL 535 50 to 50 k 5 to 100 k ±5% ± 0.25 % 100 ENR 1800° +10° -0° -0° 1.0 W 2.0 W 1.5 W 1000 M minimum 500 VDC 1000 VRMS minimum 60 Hz Not to exceed linearity x total resistance or 1 , whichever is greater 20 ppm/°C (standard values, wire only) 0.25 % of total applied voltage, maximum CCW end points - section 2 phased to section 1 within ± 2° Center tap only MARKING RESISTANCE VALUES Unit identification Manufacturer’s name and model number, resistance value and tolerance, linearity specification date code and terminal identification. Example of a marking for a standard part: 534-11103 533 ( 50, 100, 200, 500, 1K, 2K, 5K, 10K, 20K 534 ( 100, 200, 500, 1K, 2K, 5K, 10K, 20K, 50K, 100K 535 ( 50, 100, 200, 500, 1K, 2K, 5K, 10K, 20K, 50K ORDERING INFORMATION 5 3 4 B 2 MODEL STYLE GANGS 533 534 535 B: Bushing S: Servo 1 2 1 0 OHMIC VALUE GANGS No 1 470 = 47 222 = 2.200 103 = 10 k For ohmic value range see electrical specification 3 2 OHMIC VALUE GANGS No 2 470 = 47 222 = 2.200 103 = 10 k For ohmic value range see electrical specification 0 3 J TOLERANCE ON OHMIC VALUE J=±5% F=±1% C 4 7 0 LINEARITY SPECIAL REQUEST C = ± 0.25 % D = ± 0.1 % L = ± 0.2 % E = ± 0.05 % Special code xxxx PART NUMBER DESCRIPTION (for information only) 534- 1 2 103 203 xxxx MODEL STYLE GANGS OHMIC VALUE GANGS No 1 OHMIC VALUE GANGS No 2 SPECIAL B: 1 S: 2 Revision: 30-Jun-15 Document Number: 57065 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Model 533, 534, 535 www.vishay.com Vishay Spectrol SINGLE SECTION DIMENSIONS in inches (millimeters) ± 0.015 ± 0.031 0.812 (20.62) 0.750 (19.05) ± 0.015 0.312 (7.92) 0.030 MAX. (0.76) 0.062 (1.57) 0.200 MIN. (5.08) BUSHING MOUNT MODEL: 534B/534-1 METRIC SHAFT: 534B...8872 2 1 3 + 0.0000 Ø 0.2497 (6.34) - 0.0003 ± 0.015 + 0.0000 - 0.0020 Ø 0.4062 (10.32) Ø 0.875 (22.22) + 0.000 Ø 6.00 mm - 0.0003 ± 0.010 0.032 x 0.032 (0.81) x (0.81) DP 3/ - 32UNEF - 2A SCREWDRIVER SLOT ± 0.031 0.850 (21.59) ± 0.015 0.375 (9.52) 9 mm x 0.75 P 8 0.062 (1.57) 0.057 (1.45) MIN. 2 SERVO MOUNT MODEL: 534S/534-2 Ø 0.875 (22.22) 30° TYP. 0.062 (1.57) 0.300 (7.62) MIN. 1 3 R 0.625 MAX. (15.88) + 0.0000 Ø 0.7500 (19.05) - 0.0005 Ø 0.1248 (3.17) ± 0.015 + 0.0000 - 0.0003 2 CW 1 Ø 0.875 (22.22) Ø 0.750 (19.05) MAX. 3 SCHEMATIC Mounting hardware, washer and panel nut, nickel plated MECHANICAL SPECIFICATIONS PARAMETER Bearing type Bushing: Sleeve bearing Servo: Ball bearing Torque (maximums): starting Section 1 Section 2 534 0.5 oz. - in (36 g - cm) 0.9 oz. - in (65 g - cm) 533/535 0.7 oz. - in (50 g - cm) 1.1 oz. - in (79 g - cm) Torque (maximums): running Section 1 Section 2 534 0.4 oz. - in (28.80 g - cm) 0.7 oz. - in (50.40 g - cm) 533/535 0.6 oz. - in (43.20 g - cm) 0.9 oz. - in (64.8 g - cm) Weight (maximums) Section1 Section 2 0.75 oz. (21.26 g) 1.25 oz. (35.44 g) Stop strength 75 oz. - in (static) (5.4 kg - cm) Ganging 2 sections maximum POWER RATING CHART ENVIRONMENTAL SPECIFICATIONS 4 Vibration Shock RATED POWER IN W 534 535 Rotational life (shaft revolution) 533 534 534 (servo) 535 533 Load life 3 2 Temperature range 1 15 g thru 2000 Hz 50 g 300 000 1 000 000 > 1 000 000 500 000 900 h -55 °C to +125 °C Note • Nothing stated herein shall be construed as a guarantee of quality or durability. 0 0 20 40 60 80 100 120 140 160 AMBIENT TEMPERATURE IN °C Revision: 30-Jun-15 Document Number: 57065 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Model 533, 534, 535 www.vishay.com Vishay Spectrol RESISTANCE ELEMENT DATA RESISTANCE VALUE () RESOLUTION (%) OHMS PER TURN MAXIMUM CURRENT AT 70 °C AMBIENT (mA) MAXIMUM VOLTAGE ACROSS COIL (V) 533 534 535 533 534 535 533 534 535 533 534 535 533 534 535 50 - 50 0.149 - 0.120 0.0746 - 0.0603 141.0 - 173.0 7.07 - 8.66 100 100 100 0.111 0.060 0.075 0.1114 0.0603 0.0746 100.0 141.0 122.0 10.0 14.1 12.2 200 200 200 0.097 0.037 0.061 0.1954 0.0746 0.1220 70.7 100.0 86.6 14.1 20.0 17.3 500 500 500 0.069 0.031 0.049 0.3424 0.1520 0.2459 44.7 63.2 54.7 22.4 31.6 27.4 1K 1K 1K 0.063 0.025 0.041 0.6331 0.2459 0.4113 31.6 44.7 38.7 31.6 44.7 38.7 2K 2K 2K 0.041 0.021 0.031 0.8206 0.4113 0.6331 22.4 31.6 27.4 44.7 63.2 54.8 5K 5K 5K 0.044 0.016 0.034 2.2330 0.8206 1.7230 14.1 20.0 17.3 70.7 100.0 86.6 10K 10K 10K 0.034 0.017 0.030 3.4510 1.7230 3.0160 10.0 14.1 12.2 100.0 141.0 122.0 20K 20K 20K 0.031 0.015 0.020 6.1790 3.0160 3.9910 7.07 10.0 8.66 141.0 200.0 173.0 - 50K 50K - 0.009 0.015 - 4.6690 7.4560 - 6.32 5.47 - 316.0 274.0 - 100K - - 0.007 - - 7.4560 - - 4.47 - - 447.0 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Revision: 30-Jun-15 Document Number: 57065 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000